NAVY MIL-DTL-14804 B-1996 INITIATOR CARTRIDGE ACTUATED DELAY M4A1 M12A1 M45A1 AND M49A1 REMANUFACTURED METAL PARTS ASSEMBLY《 M4A1 M12A1 M45A1 和M49A1 型再造金属零件装配延迟弹筒驱动引发器》.pdf

《NAVY MIL-DTL-14804 B-1996 INITIATOR CARTRIDGE ACTUATED DELAY M4A1 M12A1 M45A1 AND M49A1 REMANUFACTURED METAL PARTS ASSEMBLY《 M4A1 M12A1 M45A1 和M49A1 型再造金属零件装配延迟弹筒驱动引发器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-14804 B-1996 INITIATOR CARTRIDGE ACTUATED DELAY M4A1 M12A1 M45A1 AND M49A1 REMANUFACTURED METAL PARTS ASSEMBLY《 M4A1 M12A1 M45A1 和M49A1 型再造金属零件装配延迟弹筒驱动引发器》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、1 TNCH-POUND I MIL-DTL- 14804B(OS) 3 Julv 1996 SUPERSEDING 14 March 1994 MIL-I- 14804A DETAIL SPECIFICATION INITIATOR, CARTRIDGE ACTUATED, DELAY M4A1, M12A1, M45A1, and M49A1 REMANUFACTURED METAL PARTS ASSEMBLY This specif cation is approved by the Naval Sea Systems Command, Department of the Navy,

2、and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for the M4A1, M 12A 1, M45A 1, and M49A 1 Delay Cartridge Actuated Initiator Remanufactured Metal Parts Assembly (see 6.1). 2. APPLICABLE DOCUMENTS 2.

3、1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the comp

4、leteness of this list, document users are cautioned that they must meet all specified requirements documents specified in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, st

5、andards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplements thereto, cited in the solicitation (

6、see 6.2). SPECIFICATIONS MILITARY MIL-A-255 O Ammunition, General Specification For Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Indian Head Division, Naval Surface Warfare Center,

7、 Standardization Branch (Code 8420), 10 1 Strauss Avenue, Indian Head, MD 20640-5035, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by sending a letter. AMSC NIA FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distr

8、ibution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL- 14804B(OS) STANDARDS MILITARY MIL-STD-4 13 Visual Inspection Guide for Elastomeric O-rings (Unless otherwise indicated, copies of militaq specifications and standards are

9、available from Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 191 11-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified he

10、rein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS Naval Surface Warfare Center. Indian Head CAGE Codes 19200 and 19203) 8595817 Initiator, Cartridge Actuated, Delay, Metal Parts Assembly 8796826 Box, Fiberboard (inner) Packing, Ammunition, for Initiator, Cart

11、ridge Actuated, Delay, M4A1, M6A1, M12A1, M26, M33, M44, M45A1, or M49A1 8796827 Box, Packing, Ammunition, for Initiator, Carridge Actuated, Delay, M4A 1, M6A1, M12A1, M26, M33, M44, M45A1, or M49A1 92 16824 Box, Fiberboard (Outer) Alternative, Packing, Ammunition, for Initiator, Cartridge Actuated,

12、 Delay, M4A1, M6A1, M12A1, M26, M33, M44, M45A1, or M49A1 (Application for copies should be addressed to: Commander, Indian Head Division, Naval Surface Warfare Center, Attn: Data Control Branch (Code 8410), Indian Head, MD 20640-5035.) 23 Non-Government publications. The following documents form a

13、part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the do

14、cuments cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR QUALITY CONTROL ASQCZ1.4 Sampling Procedures and Tables for Inspection by Attributes ASQC A8402 Quality Management and Quality Assurance-Vocabulary (Application for copies should be addressed to the American Society for Quality Contro

15、l, PO Box 3005,611 E. Wisconsin Ave., Milwaukee, WI 53201-4606.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-lt404B 906 20Lltb 068 = MIL-DTL- 14804B(OS) 2.4 Order of precedence. In the event of a conflict between the text of this docume

16、nt and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials. All materials used in the manufacture of the initiators shall co

17、nform to the specifications referred to on the respective drawings unless specific approval in writing covering a departure therefrom has been obtained from the cognizant Navy design activity prior to manufacture. When alternate materials or methods of manufacture are specified on the drawings, the

18、bidders selections shall be clearly stated in the proposal. The remanufactured metal parts assembly shall contain a new safety pin, initiator spring, O-rings, and seal. 3.2 Hydrostatic pressure. The initiator cap, chamber, and plug, simulating the firing pin housing (without a firing pin pin hole bu

19、t with an O-ring), shall withstand an internal hydrostatic pressure of 5500 to 6500 pounds per square inch (psi) for 15 seconds minimum, without deformation or mechanical failure (see 6.4.1). 33 Protective finish. Protective finish shall be in accordance with the applicable specifications and drawin

20、gs and shall apply to all surfaces of the component, regardless of configuration. Remanufactured exterior components shall have the existing protective finish stripped and the specified protective finish reapplied (see 6.4.2). 3.4 Residual magnetism. The metal parts assembly shall not deflect the in

21、dicator of the compass more than 5 degrees in either direction (see 4.5.5). 35 Firing pin release. The firing pin of the assembled initiator, less safety pin, cartridge retainer and chamber, shall release from the cocked position when the application of an axial load of 20 to 35 pounds has withdrawn

22、 the initiator pin 3/4 inches, maximum. 3.6 Initiator pin security. The initiator pin of the assembled initiator, less cartridge retainer and chamber, shall not withdraw beyond the safey pin when subjected to an axial load of 200 to 220 pounds. Application of the load shall cause no deformation of t

23、he safety pin. 3.6.1 Initiator pin. Check safey pin groove length for 0.1 18 f 0.010 inch dimension (100 percent inspection.) 3.7 Metal parts assembly. Parts shall be combined to produce an assembly that conforms to the requirements of the metal parts assembly drawing. Ali threaded joints shall be a

24、ssembled handtight. 3.7.1 Integrated plant products. When remanufacturing and loading of the assembly is performed in an integrated plant, the metal parts assembly requirement may be waived and the residual magnetism requirement performed on the loaded assembly only. 3.7.2 Threaded component parts.

25、Class 2A or 2B thread gage shall be used on component part inspection versus class 3A or 3B thread gage required on remanufactured hardware for initiators. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-LLlOLlB = 9999906 2019168 TT4 MIL-DT

26、L- 14804B(OS) 3.8 Workmanship. Assemblies shall be free of cracks, splits, or other defects which might prevent proper mating with connecting parts or proper functioning of the device. 3.8.1 Metal defects. All components shall be free from cracks, splits, cold shuts, inclusions, porosi, or any simil

27、ar defect. 3.8.2 Burr. No part shall have a burr which might interfere with the assembly or function of the item or which might be injurious to personnel handling the item. 3.8.3 Foreign matter. No part or assembly shall contain chips, dirt, grease, rust, corrosion, or other foreign matter. 4. VERIF

28、ICATION 4.1 Quality assurance terms and definitions. Reference shall be made to ASQC A8402 to define the quality assurance terms used. 4.1.1 Inspections. Inspections shall be in accordance with MIL-A-2550. 4.2 Inspection conditions. Unless otherwise specified (see 6.2), all inspections shall be perf

29、ormed under the following conditions: a. Temperature: Room ambient (68 to 77F) b. Altitude: Sea level c. Humidity: 50 percent relative, maximum d. Atmospheric pressure: 14.7 psi 4.3 Quality conformance inspection. 4.3.1 Lot. 4.3.1.1 Submission of product. Unless otherwise specified by the contractin

30、g activity, formation and identification of lots shall be in accordance with ASQC 21.4. 4.3.1.2 Size of lot. For the purpose of identification and shipment, the shipping lots of metal parts assemblies shall consist of 1200 assemblies maximum, provided the homogeneity requirement of inspection lots h

31、ave been retained. 43.2 Examination. On reprocessed parts, one hundred percent examination shall be performed for all critical defects. Examination for major and minor defects shall be performed in accordance with the classification of defects, using the sampling plan and associated criteria specifi

32、ed in the contract (see 6.2 and 6.3). Four power (4x) magnification may be used for inspection of such defects as burr and foreign matter. Inspection for rubber O-rings shall be in accordance with MIL-STD-413. When compliance with the applicable requirement is in doubt as a result of visual examinat

33、ion, the characteristic shall be measured or gaged to determine acceptability. All nonconforming material shall be rejected. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-DTL-L4804B = 999990b 20L91b9 930 MIL-DTL- 14804B(OS) 4.3.2.1 Examinati

34、on of reclaimed parts. Examination of reusable parts that require no reprocessing shall be limited to inspecting only those defects requiring visual inspection. One hundred percent examination shall be performed for all such defects. All nonconforming parts shall be reprocessed or rejected. 4.3.2.2

35、Pin, Initiator, Drawing 8595403, covering a detail of Drawing 8595817. Characteristics Defect Method of Inspection Critical None defined Major 101 Metal defective Visual 102 Protective finish inadequate or defective Visual 103 Surface finish on body and body groove improper Visual 104 BLUT Visual 10

36、5 Foreign matter Visual Minor 20 1 Surface finish improper, except as otherwise classified Visual 4.3.2.3 Cap, Drawing 8595404, covering a detail of Drawing 8595817. Critical 1 Metal defective Major 101 102 103 104 105 106 107 108 109 Pitch diameter of large thread, max Minor diameter of large threa

37、d, max Pitch diameter of small thread, max Minor diameter of small thread, max Thread damaged Metal defective, except as otherwise classified Protective finish inadequate or defective BLUT Foreign matter Visual Gage Gage Gage Gage Visual Visual Visual Visual Visual Minor None defined 4.3.2.4 Housing

38、, Firing Pin, Drawing 8595408, covering a detail of Drawing 859581 7. Critical 1 Metal defective 5 Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Major 101 102 103 104 105 106 107 108 1 o9 MIL-DTL- 14804B(OS) Pitch diameter of small thread, m

39、in Major diameter of small thread, min Pitch diameter of large thread, min Major diameter of large thread, min Thread damaged Protective finish inadequate or defective Surface finish in cavity improper Burr or sharp comer Foreign matter Minor 20 1 Surface finish improper, except as otherwise classif

40、ied 4.3.2.5 Pin, Firing, Drawing 8595407, covering a detail of Drawing 8595817. Critical None defined Major 101 Metal defective 102 103 Surface finish improper 104 Burr or sharp edge 105 Foreign matter Protective finish inadequate or defective Gage Gage Gage Gage Visual Visual Visual Visual Visual V

41、isual Visual Visual Visual Visual Visual Minor None defined 4.3.2.6 Chamber, Initiator, Drawing 8593314, covering a detail of Drawing 859581 7. Critical 1 Metal defective Major 101 102 103 104 105 106 107 108 1 o9 Pitch diameter of large thread, min Major diameter of large thread, min Pitch diameter

42、 of small thread, min Major diameter of small thread, min Thread damaged Protective finish inadequate or defective Surface finish, end of gas port, improper Burr Foreign matter Visual Gage Gage Gage Gage Visual Visual Visual Visual Visual 6 Provided by IHSNot for ResaleNo reproduction or networking

43、permitted without license from IHS-,-,-MIL-DTL- 14804B(OS) Minor 20 1 Surface finish improper, except as otherwise classified 4.3.2.7 Retainer, Cartridge, Drawing 8593313, covering a detail of Dram ig 85958 Critical 1 Metering slots in base missing Major 101 102 103 104 105 106 107 108 Pitch diamete

44、r of thread, max Minor diameter of thread, max Elongated slots missing Thread damaged Metal defective Protective finish inadequate or defective BLUT Foreign matter Visual 7. Visual Gage Gage Visual Visual Visual Visual Visual Visual Minor None defined 4.3.2.8 Assembly, Drawing 8595817, less all draw

45、ings except 8595408.8595407,8595403,8595406, MS19060 and MS28775. Critical 1 Protrusion of firing pin 2 Steel ball missing 3 O-ring missing Major None defined Minor 20 1 Lubricant missing from O-ring 4.3.2.9 Assembly, Drawing 8595817. Critical None defined Major 101 102 103 Any part missing 104 Impr

46、oper assembly Initiator pin not free to rotate Safety pin loose or deformed Gage Gage Visual Visual Manual ManualNisual Visual Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-DTL-14804B 0b 2017172 425 = 4. MIL-DTL- 14804B(OS) Minor 20 1 P

47、rotective cap missing 202 Protective finish inadequate or defective 4.3.2.10 Box, Fiberboard (Inner) Packing, Ammunition, Drawing 8796826. Critical None defined Major None defined Minor 20 1 Contents loose 202 Box damaged 203 204 Marking missing, incorrect, or illegible Cut, damaged, or improperly s

48、ealed bag Visual Visual Manual Visual Visual Visual 4.3.2.1 1 Box, Packing, Ammunition, Drawing 8796827. Critical None defined Major None defined Minor 20 1 Contents loose VisuaVManual 202 Strapping missing, loose, broken, or improperly assembled Visual/Manual 203 Contents of box exposed Visual 204

49、Box damaged Visual 205 Marking missing, incorrect, or illegible Visual 206 Number of units incorrect Visual 4.3.2.12 Box, Fiberboard (Outer) Alternative, Packing, Ammunition, Drawing 9216824. Critical None defined Major None defined Minor 20 1 202 203 Contents loose ManualVisual Hardware missing, loose, broken, or improperly engaged Strapping missing, loose, broken, or improperly engaged Visual Visual 8 Provided by IHSNot f