NAVISTAR MPAPS K-6904-2017 Tape Plastic Electrical Adhesive Type.pdf

《NAVISTAR MPAPS K-6904-2017 Tape Plastic Electrical Adhesive Type.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS K-6904-2017 Tape Plastic Electrical Adhesive Type.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. FEBRUARY 2017 Page 1 of 5 NAVISTAR, INC. Material, Parts, and Process Specificati

2、ons (MPAPS) NUMBER: MPAPS K-6904 Former Designation: TMS 6904 TITLE: Tape, Plastic Electrical, Adhesive Type CURRENT REV No.: 1702 DATE: Feb. 2017 WRITTEN/EDITED BY: A. Hasan APPROVED BY: R. Goluch SUPERSEDES: Rev. 0904 April 2009 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION

3、 This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory

4、 limits prior to use. 1.0 APPLICATION This specification covers four types of PVC (or copolymers) tape, with a pressure-sensitive coating. 1.1 Type IA is used for insulating electrical splices. 1.2 Type IB is used to hold wires and conduit together and is not used to insulate electrical splices. 1.3

5、 Type II is used in special applications where a heavier tape is required. 1.4 Type III is made in colors, used for color coding, and is not a suitable substitute for Types I or II. 2.0 SCOPE This specification covers general property and performance requirements, quality control and approved source

6、s, and approved sources for four (4) grades of tapes. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, th

7、e latest issue of all referenced standards shall apply. The following Specifications, Standards, and Regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 NAVISTAR MPAPS P-9543 CFR Title 29, Part 1910 ASTM B117 NAVISTAR Supplier Packing and Shipping Std. D-13

8、 ASTM D1000 NAVISTAR Engineering Design Std. A-16 ASTM D2247 NAVISTAR MPAPS B-50 ASTM D4325 4.0 REQUIREMENTS 4.1 Dimensions This tape shall be furnished on 25.4 mm (1 in) diameter cores unless otherwise specified and should be ordered in the following preferred widths: 6.4 mm (1/4 in) 15.9 mm (5/8 i

9、n) 9.5 mm (3/8 in) 19.0 mm (3/4 in) 12.7 mm (1/2 in) 25.4 mm (1 in) NUMBER: MPAPS K-6904 TITLE: Tape, Plastic Electrical, Adhesive Type REVISION: 1702 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers

10、 are required to assume all patent liability. 2017 by Navistar, Inc. FEBRUARY 2017 Page 2 of 5 Wider tapes are available. Unless otherwise specified, roll lengths will be 33.0 m (108 ft). 4.2 Property and Performance Requirements This tape is furnished in four types, having the following requirement

11、s. Unless otherwise specified, test in accordance with ASTM D1000 or ASTM D4325 as appropriate. Property or Performance Requirement Type IA Type IB Type II Type III Total Thickness, mm 0.18 0.02 0.16 0.05 0.25 0.02 0.12 min mil 7 1 6 2 10 1 4.8 min Backing Thickness, mm 0.15 0.02 0.13 0.02 0.23 0.02

12、 0.10 min mil 6 1 5 1 9 1 3.8 min Tensile Strength, kN/m width, min 3.5 1.7 5.2 2.4 lbf/in width, min 20 9.6 30 14 Adhesion, N/m width, min 219 219 274 219 oz/in width, min 20 20 25 20 Elongation at break, % min 200 200 100 125 Resistance to penetration, Degrees C 90 90 120 90 Degrees F 194 194 248

13、194 Dielectric Strength (volts RMS, 60 cycles) 10,000 10,000 11,000 NA Insulation Resistance (at 90% relative humidity, at 32C (90F), for 48 hours on samples of 25.4 x 25.4 mm (1 x 1 in) 20,000 20,000 20,000 NA Storage Stability, months, min. 10 10 10 10 Electrolytic Corrosion Factor 1.0 1.0 1.0 1.0

14、 Color Black Black Black As specified* * Color black may not be selected for this type 4.2.1 Chemical Resistance: These tapes shall have resistance to air, water, acid, alkali, gasoline and corrosive chemicals, and shall have fire retardant qualities. Test per ASTM D 1000. 4.2.2 Humidity 4.2.2.1 Met

15、hod Test prepared tape wrapped samples per ASTM D2247, for 500 hour exposure. 4.2.2.2 Required Tape should maintain sufficient holding strength. 4.2.3 Thermal Cycling 4.2.3.1 Method Test tape wrapped samples in a cyclic environment chamber. Test method is as follows: 16 hours 70C 2C (160F 3.6F) 3 ho

16、urs 25C 2C (-13F 3.6F) 3 hours 100C 2C (212F 3.6F) 2 hours stabilization at 23C 2C (73F 3.6F) Repeat 24 hour cycle 5 times 4.2.3.2 Required Tape should maintain sufficient holding strength. NUMBER: MPAPS K-6904 TITLE: Tape, Plastic Electrical, Adhesive Type REVISION: 1702 This document is restricted

17、 and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. FEBRUARY 2017 Page 3 of 5 4.2.4 Corrosion 4.2.4.1 Method Test pre-determined tape wrapped samples to ASTM B11

18、7 salt spray test. 4.2.4.2 Required Tape should maintain sufficient holding strength. 5.0 QUALITY All product supplied shall be clean and free from dirt, oils, sharp edges, or defects harmful to product performance. 6.0 QUALIFICATION Engineering qualification of sources is required in advance of pro

19、duction shipments. Samples shall be accompanied by test data certifying that all requirements of the specification have been met. Suppliers shall submit samples for approval of finish, luster, color and appearance to the Navistar Industrial Design Group. Upon approval, styling master samples denotin

20、g the minimum level of acceptable appearance quality shall be developed and retained by the supplier and the quality department of each using NAVISTAR facility. 6.1 Quality Control Plan A Quality Control Plan for products supplied to the requirements of this specification will be established by mutu

21、al agreement between NAVISTAR and the supplier. Unless specific exception is noted, the following characteristics, where applicable*, shall be included in the plan as features for management by statistical process control.* * Other characteristics for inclusion in the control plan may be specified o

22、n the engineering drawing and/or purchase order. * See NAVISTAR Engineering Design Standard A-16 7.0 SOURCE APPROVAL AND QUALITY CONTROL 7.1 Supplier Requirements All suppliers to NAVISTAR are required to be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS-16949 regis

23、tration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Corporate Buyer upon reque

24、st. 7.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in mat

25、erial, properties, NUMBER: MPAPS K-6904 TITLE: Tape, Plastic Electrical, Adhesive Type REVISION: 1702 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 201

26、7 by Navistar, Inc. FEBRUARY 2017 Page 4 of 5 processing practices, construction, color, or labeling of the product are required, the supplier shall notify NAVISTAR Materials Engineering and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requir

27、ements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 7.3 Process Control The supplier shall either, perform and report results of tests on specific lo

28、ts of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the quality control manager of the using NAVISTAR plant

29、 may determine testing and reporting requirements on specific products. 8.0 SHIPPING AND HANDLING Shipping and identification shall be in accordance with NAVISTAR Supplier Packing and Shipping Standard D-13. Parts shall be packaged so as to avoid any damage in shipment detrimental to the appearance

30、of the part. 9.0 DESIGNATION ON DRAWINGS Include both width and type when specifying or ordering these tapes. When Type III is selected, the color shall be included. Example of note to use on drawings: MPAPS K- 6904, Type IA, 19.0 mm (3.4 in) wide MPAPS K- 6904, Type III, 12.7 mm (1/2 in) wide, colo

31、r yellow 9.1 NOTE Specification on Existing Drawings: For existing drawings, which specify Type I Tape, without reference to either Type IA or Type IB, Type IA shall be supplied. 10.0 APPROVED SOURCES Type IA Type IB Type II Type III Minnesota Mining & Mfg. Co. (3M) #1700 - - #35 Dutch Brand (Nashua

32、 Corp) A-7 - A-10 A-5 Staff Company Staffco HPS-SP - - Staffco 45-Y Plymouth Rubber Company - #873 & #316 - Slipnot #44 Essex International Insulation Div. Permacel #29 - - - (Essex #290) NUMBER: MPAPS K-6904 TITLE: Tape, Plastic Electrical, Adhesive Type REVISION: 1702 This document is restricted a

33、nd may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2017 by Navistar, Inc. FEBRUARY 2017 Page 5 of 5 11.0 TECHNICAL INFORMATION For further information related to the technical content o

34、f this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Markit. Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ A.0 GENERAL INFORMATION REVISION HISTORY Revision Level Change Approved by Date Approved 1702 Converted to MPAPS R. Goluch 2/28/2017