FORD FLTM BN 110-01-2017 RESISTANCE TO DENIM DYE TRANSFER FOR SEAT TRIM MATERIAL.pdf

《FORD FLTM BN 110-01-2017 RESISTANCE TO DENIM DYE TRANSFER FOR SEAT TRIM MATERIAL.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BN 110-01-2017 RESISTANCE TO DENIM DYE TRANSFER FOR SEAT TRIM MATERIAL.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHOD BN 110-01 Date Action Revisions Rev. 00 2017 06 14 Released Z. Jatkowski, NA Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 2 RESISTANCE TO DENIM DYE TRANSFER FOR SEAT TRIM MATERIAL Application This procedure is used to determine

2、the resistance of leather and vinyl to denim dye transfer. Apparatus and Materials Required Martindale abrasion machine with specimen holder weights Rotational speed of outer pegs = 47.5 2.5 rev/min Ratio of speeds outer pegs : inner pegs = 32:30 or 16:15 Total stroke of outer pegs = 60.5 mm 0.5 mm

3、Total stroke of inner pegs = 60.5 mm 0.5 mm Working area of specimen holder = 645 mm2 Nominal pressure on test specimen = 12 kPa Lissajous figure stroke = 60 1 mm Available from: SDL Atlas, LLC James H. Heal & Co. LTD 3934 Airway Dr OR Richmond Works Rock Hill, SC 29732-9200 USA Lakeview Tel: 1 (803

4、) 329-2110 Halifax Fax: 1 (803) 329-2133 United Kingdom www.james-heal.co.uk/ Test Fabric Denim 2550Y Available from: Test Fabrics, Inc. 415 Delaware Ave West Pittston, PA 18643 USA Tel: 1 (570) 603-0432 Fax: 1 (570) 603-0433 Email: http:/ Syringe 10 mL volume minimum Backing for specimen and test

5、 fabric denim Woven wool felt mass 750 50 g/m2 and approximately 2.5 0.5mm thick SDL Atlas USA material code is M235 E or M235 E1 Available from: SDL Atlas, LLC Schsisches Textilforschungsinstitut E.V 3934 Airway Dr OR STFI Rock Hill, SC 29732-9200 Annaberger Str. 240 USA Postfach 13 25 Tel: 1 (803)

6、 329-2110 09072 Chemnitz Fax: 1.803.329.2133 Germany FORD LABORATORY TEST METHOD BN 110-01 Copyright 2017, Ford Global Technologies, LLC Page 2 of 2 Recommended Cleaning Agents See FLTM BN 112-08 Chemicals, materials, parts, and equipment referenced in this document must be used and handled properl

7、y. Each party is responsible for determining proper use and handling in its facilities. Sample and Test Conditioning Sample Conditioning All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 2 C and 50 5% relative humidity for not less than 24 h prior to

8、 testing and tested as soon as possible after removing from the specified conditions. Materials to be conditioned are the submitted material for evaluation and the 2550Y test denim. Sample Size Cut two circular specimens 140 mm in diameter from the provided sample and 2550Y test denim. Procedure 1.

9、Mount the conditioned specimens over the backing felt on the machine tables with the A surface facing up. 2. Lay the conditioned denim specimens in a flat, non-absorbable container/dish. Wet each of the 140 mm denim specimens with 10 mL of room temperature (23 +- 2 C) deionized water using a syringe

10、, swirling outwards from the center to insure even water distribution, over a time period of approximately 30 seconds. Do not wring out the denim. 3. Mount the wetted denim in the pilling holders with a 90 mm diameter piece of dry felt backing so that the blue dyed yarns are interfacing with the sam

11、ple to be tested. 4. Clamp the denim holders on the moving plate and load the holders to achieve the specified pressure of the denim of 12 kPa on the specimens. 5. Turn on the Martindale apparatus and run for 1000 cycles. 6. Place tested specimen in a cabinet or drawer that will shield it from light

12、 until the specimen is dry. 7. Evaluate one test specimen per evaluation procedure (below) within 24 hours of completing step 6. Report AATCC rating as “stain before cleaning” value. 8. Clean half of the second specimen using a recommended cleaning agent and procedure outlined in FLTM BN 112-08. Aft

13、er cleaning, store specimen in a cabinet or drawer that will shield it from light for 24 hours 9. After 24 hours, evaluate the cleaned section of specimen per evaluation procedure. Report AATCC rating as “stain level after cleaning” value. 10. Once evaluation is completed, store tested specimens in

14、a cabinet, drawer, or envelope that will shield the specimens from light. Specimen can be stored at ambient temperature. These specimens may only be used as reference for 30 days. Evaluation Visually assess the color difference between the test specimen subjected to dye transfer and the control specimen using the appropriate change in color scale in accordance with AATCC Evaluation Procedure 2. Evaluation should be made in the center of the specimen and avoiding the darker edge of the tested area.