EN ISO 15252-3-1999 en Plastics - Epoxy Powder Moulding Compounds (EP-PMCs) - Part 3 Requirements for Selected Moulding Compounds《塑料 环氧树脂模塑化合物(EP-PMCs) 第3部分 对所选模塑化合物的要求 ISO 15252-3.pdf

《EN ISO 15252-3-1999 en Plastics - Epoxy Powder Moulding Compounds (EP-PMCs) - Part 3 Requirements for Selected Moulding Compounds《塑料 环氧树脂模塑化合物(EP-PMCs) 第3部分 对所选模塑化合物的要求 ISO 15252-3.pdf》由会员分享，可在线阅读，更多相关《EN ISO 15252-3-1999 en Plastics - Epoxy Powder Moulding Compounds (EP-PMCs) - Part 3 Requirements for Selected Moulding Compounds《塑料 环氧树脂模塑化合物(EP-PMCs) 第3部分 对所选模塑化合物的要求 ISO 15252-3.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、STD-BSI BS EN IS0 15252-3-ENGL 2000 1624667 0826732 Y23 BRITISH STANDARD Plastics - Epoxy powder moulding compounds (EP-PMCS) - Part 3: Requirements for selected moulding compounds The European Standard EN IS0 152523: 1999 has the status of a British Standard ICs 83.080.10 3s EN IS0 15252-3:ZOOO NO

2、COPYING WTHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW STDOBSI BS EN IS0 15252-3-ENGL 2000 E Lh24hh9 OB26913 3bT BS EN IS0 152523:2 National foreword This British Standard is the English language version of EN IS0 15252-31999. It is identical with IS0 1525231999. The UK participation in

3、its preparation was entsusted to Technical Committee PW42, Fibre reinforced thermosettjng plastics and prepregs, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible internationaVEuropean committee any enquiries on the interpretation, or proposals for

4、 change, and keep the UK interests informed - monitor related international and European developments and promulgate them in the UK A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC

5、Standards nody include an annex which lists nonnative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “In

6、ternational Standards Correspondence Index“, or by using the “Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with

7、a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN IS0 title page, the EN IS0 foreword page, the IS0 title page, pages ii and iii, a blank page, pages 1 to 6, an inside back cover and a b

8、ack cover. The BSI copyright notice displayed in this document indicates when the document was last issued. This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into

9、 effect on 15 January Zoo0 O BSI 01-2000 Amendments issued since publication ID - particle size; - moisture content. If this is so, these properties and test methods, as well as the test conditions to be used, shall be as agreed between the interested parties. 4.2 Filler/reinforcement type and conte

10、nt In order for an epoxy powder moulding compound to be considered as complying with this part of IS0 15252, the nature, form and content by mass of its fillerheinforcement shall be as given in the designation of the moulding compound (see IS0 15252-1 :1999, subclause 4.2). 2 STD-BSI BS EN IS0 L5252

11、-3-ENGL 2000 II Lb24bb9 082b920 5TT EN IS0 15252-3:1999 Pro- Max. inga min. Property Unit cess- or I I 4 1 2 3 Type: PMC IS0 15252-EP . MD65,X,E MD5,X,T (GFlO+MD60) (GFlO+MDO),X,E MD75,X,E MD75,X,T (GF20+MD50) (GFPO+MDSO),X,E to to to to I Rheological and processing properties . .i Stress at break,

12、uB .2 Flexural strength, qM .3 Charpy impact strength, uCu .4 Charpy notched impact strength a, _ To be agreed between the interested parties - - - - Q 2 40 40 70 70 Q 2 80 90 120 120 80 90 130 130 5,O 58 Q,O 990 , 1.5 1.5 %O 3,O MPa MPa kJlm2 a Q a 5,O 58 7,O 7,o kJlm2 Q 2 15 1,s 2,o 2,o I Mechenlc

13、al DroDerties i.1 1.2 1.3 OC Q/M 3 130 180 150 150 OC Q/M 2 90 120 1 O0 1 O0 Temperature of deflection under load, T,1,8 Temperature of deflection under load, T,8,0 Flammability (glow bar), BH - QiM G BH 2-30 BH 2-30 BH 2-10 BH 2-10 Water absorption, W34 i Q = Compression moulding M = Injection moul

14、ding NOTE 1 See IS0 15252-2:1999, Tables 3 and 4, columns 3, 4 and 7, for the methods to be used for the preparation of t6 specimens and the determination of properties. NOTE 2 In view of the differences between the propery-value limits for compression-moulding and injection-moulding materials, tl l

15、ikely variations in test results and the wide range of properties covered, it should not be assumed that materials having the sar designation are exactly equivalent. 3 STD.BSI BS EN IS0 15252-3-ENGL 2000 H 1624667 0826923 43b m EN IS0 15252-3:1999 - 70 110 120 8,O 10,o Table 2 - Property requirement

16、s for EP-PMCs containing (GF+MD) as filler - - - 70 70 80 130 130 150 140 140 160 8,O 7,o 8,O 10,o 9,o 10,o I 6 I 7 I 8 5 Type: PMC IS0 15252-EP . Charpy impact strength, %U Property kJ/m2 Q a 2.4 3 1 I Rheological and processing properties Charpy notched impact kJ/m2 Q 2 3,o 4,o 23 23 Thermal prope

17、rties strength a,* 2 40 5,O 4,5 395 1.1 I 4 4.1 4.2 4.3 4.4 5 To be aareed between the interested Darties Electrical properties Dissipation factor, tan 6 1 O0 - Q/M - 0,03 - - Volume resistivity, pe R.cm Q/M 2 1013 1 014 1013 1014 Surface resistivity, ae R WM 3 1012 1013 1012 1013 Proof tracking ind

18、ex, PTI - Q/M 2 250 600 400 250 Other properties 2 I Mechanical properties 5.1 5.2 - 2.1 I Stress at break, oB IMPaI M I $ m9 40 30 30 30 Water absorption, w,.,24 % by Q/M - - - - mass 2.2 Flexural strength, qM I 3 I “C 1 Q/M I 2 3.1 Temperature of deflection I under load, T,1,8 I “C (WMI 2 3.2 Temp

19、erature of deflection I under load, T,8,0 3.3 Flammability (glow bar), I BH I Q/M I 200 200 180 180 120 120 120 120 BH2-10 I BH2-10 I BH2-10 I BH2-10 a Q = Compression moulding M = Injection moulding NOTE 1 See IS0 15252-2:1999, Tables 3 and 4, columns 3, 4, and 7, for the methods to be used for the

20、 preparation of tes specimens and the determination of properties. NOTE 2 In view of the differences between the property-value limits for compression-moulding and injection-moulding materials, the likely variations in test results and the wide range of properties covered, it should not be assumed t

21、hat materials having the same designation are exactly equivalent. 4 STDmBSI BS EN IS0 L5252-3-ENGL 2000 1624669 0826722 372 H EN IS0 15252-3:1999 Pro- Max. inga min. Property Unit cess- or Type: PMC IS0 15252-EP . (GF25+GG25) to (GF35+GG15) - - - - 1 1.1 2 2.1 - 7 - - 2.2 2.3 - - 2.4 - 3 3.1 - - 3.2

22、 - 3.3 - 4 4.1 7 - 4.2 4.3 4.4 5 5.1 5.2 - - - - - - M = Injection moulding NOTE 1 See IS0 15252-2:1999, Tables 3 and 4, columns 3, 4, and 7, for the methods to be used for the preparation of te specimens and the determination of properties. NOTE 2 In view of the differences between the property-val

23、ue limits for compression-moulding and injection-moulding materials, tk likely variations in test results and the wide range of properties covered, it should not be assumed that materials having the san designation are exactly equivalent. Stress at break, oB MPa lexural strength, a, MPa kJ/m2 ;harpy

24、 impact strength, CU :harpy notched impact kJ/m2 jtrength uCA To be agreed between the interested parties lechanical properties - Q 2 50 2 Q 2 120 130 Q 2 6,O 6,O Q 2 2,o 2 2.0 2 2 OC Temperature of deflection under load, Tll ,8 Temperature of deflection under load, T18,0 Flammability (glow bar), BH

25、 “C - rhermal properties Q/M 2 150 Q/M 2 1 O0 WM G BH 2-1 O Dissipation factor, tan6100 Electrical properties - Q/M - Volume resistivity, pe Surface resistivity, o. R.cm Q/M 2 1013 Q QIM 2 102 Proof tracking index, PTI - Q/M 2 250 I I I mg Water absorption, W24 % by mass Other properties 30 - Q/M 5

26、STD-BSI BS EN IS0 L5252-3-ENGL 2000 Lb24hb7 O826923 209 EN IS0 15252-3:1999 National or international standard Annex A (inform at ive) 1 2 3 4 5 Type: PMC IS0 15252-EP . Comparison of designations IS0 15252-3:1999 IS0 Table A.l - Comparison of designations used for EP-PMCs in national and internatio

27、nal standards MD65,X, E MD65,X,T (GFlO+MD60) (GFlO+MDGO),X,E (GF15+MD55) MD75,X,E MD75,X,T (GF20+MD50) (GF20+MDSO),X,E (GF25+MD45) to to to to to - - - - - 6 7 8 9 10 Table A.l - Comparison of designations used for EP-PMCs in national and international standards (continued) (GF20+MDSO),X,E to (GF30+

28、MD40),X, E - National or international standard _ (GF20+MD50) (GF25+MD45) (GF25+GG25) to to to (GF30+MD40) (GF35+MD35) (GF35+GG 15) - - - - - IS0 15252-3:1999 IS0 Type: PMC IS0 15252-EP. . . 6 _ STD-BSI BS EN IS0 15252-3-ENGL 2000 m Lb24bb 082b24 145 H BS EN IS0 15252-3:2000 BSI 389 Chiswick High Ro

29、ad London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendm

30、ent or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard wou

31、ld mform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 020 8996 9O00. Fax: 020 8996 7400. BSI offers members an individuai updating service called PLUS which ensures that subscribers automatically receive the latest editions o

32、f standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have

33、 been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI elech-onic information services are also

34、available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 71 11. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of thes

35、e and other benefits contact Membeiship Administrati on Tel 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the intedonai standardization bodies. Except as permitted under the Copyright, Designs

36、and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written pennission from BSI. Tius does not preclude the free use, in the come of implementing the standard, of

37、 necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written pennission of BSI must be obtained If permission is granted, the terms may include royalty payments or a iicensing agreement. Details and advice can be obtained from the Copyright Manager. Tel 020 8996 7070.