EN ISO 12209-2013 en Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air (Incorporates Amendment A1 2016)《气瓶 压缩可呼吸空气用气瓶阀的出口接头》.pdf

《EN ISO 12209-2013 en Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air (Incorporates Amendment A1 2016)《气瓶 压缩可呼吸空气用气瓶阀的出口接头》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 12209-2013 en Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air (Incorporates Amendment A1 2016)《气瓶 压缩可呼吸空气用气瓶阀的出口接头》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 12209:2013Gas cylinders Outletconnections for gas cylindervalves for compressedbreathable airBS EN ISO 12209:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 12209:2013. It supersedes BS EN ISO 12209-1:2001, BS EN ISO 1

2、2209-2:2001 and BS EN ISO 12209-3:2001 which are withdrawn.The UK participation in its preparation was entrusted to Technical Committee PVE/3/1, Gas containers - Valve fittings for gas containers.A list of organizations represented on this committee can be obtained on request to its secretary.This p

3、ublication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013ISBN 978 0 580 74404 4 ICS 23.020.30Compliance with a British Standard cannot confer imm

4、unity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2013.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 12209 September

5、2013 ICS 23.020.30 Supersedes EN ISO 12209-1:2000, EN ISO 12209-2:2000, EN ISO 12209-3:2000English Version Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air (ISO 12209:2013) Bouteilles gaz - Raccords de sortie pour robinets de bouteilles gaz pour air comprim re

6、spirable (ISO 12209:2013) Gasflaschen - Ausgangsanschlsse fr Gasflaschenventile fr verdichtete Atemluft (ISO 12209:2013) This European Standard was approved by CEN on 17 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t

7、his European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official

8、 versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Aus

9、tria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swed

10、en, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CE

11、N national Members. Ref. No. EN ISO 12209:2013: EBS EN ISO 12209:2013EN ISO 12209:2013 (E) 3 Foreword This document (EN ISO 12209:2013) has been prepared by Technical Committee ISO/TC 58 “Gas cylinders“ in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat

12、 of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2014, and conflicting national standards shall be withdrawn at the latest by March 2014. Attention is drawn to the p

13、ossibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 12209-1:2000, EN ISO 12209-2:2000, EN ISO 12209-3:2000. According to the CEN-CENE

14、LEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Ic

15、eland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 12209:2013 has been approved by CEN as EN ISO 12209:2013 without any modifica

16、tion. BS EN ISO 12209:2013ISO 12209:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Yoke type outlet connection for SCUBA use up to a maximum cylinder working pressure of 232 bar 25 Threaded type outlet connections up to

17、 a maximum cylinder working pressure of 232 bar and 300 bar 45.1 General requirements . 45.2 232 bar threaded outlet connection . 45.3 300 bar threaded outlet connection . 86 Threaded type valve outlet connection for SCUBA use up to a maximum cylinder working pressure of 232 bar including adaptor fo

18、r users to convert into a yoke type outlet 117 Marking .15Annex A (normative) Outlet connection type test procedures .16Bibliography .18BS EN ISO 12209:2013ISO 12209:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO me

19、mber bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governme

20、ntal and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Direc

21、tives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodie

22、s casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 12209 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee

23、SC 2, Cylinder fittings, in collaboration with Technical Committee CEN/TC 23, Transportable gas cylinders.This first edition of ISO 12209 cancels and replaces the first editions of the ISO 12209 series (ISO 12209-1:2000, ISO 12209-2:2000, ISO 12209-3:2000), which have been technically revised.The ma

24、in changes are: combination of former three parts of ISO 12209 into a single ISO 12209; modification of valve outlet, adaptor and o-ring dimensions; and addition of an outlet connection type test procedure in Annex A.iv ISO 2013 All rights reservedBS EN ISO 12209:2013INTERNATIONAL STANDARD ISO 12209

25、:2013(E)Gas cylinders Outlet connections for gas cylinder valves for compressed breathable air1 ScopeThis International Standard specifies the characteristics of outlet connections for gas cylinder valves for compressed breathable air gas cylinders. It states the fundamental requirements for both; t

26、he connection and its components and includes basic dimensions. Included in this International Standard are the following connections: yoke type outlet connection for SCUBA use up to a maximum cylinder working pressure of 232 bar; threaded type outlet connections up to a maximum cylinder working pre

27、ssure of 232 bar and 300 bar; and threaded type outlet connection for SCUBA use up to a maximum cylinder working pressure of 232 bar including adaptor for users to convert into a yoke type outlet.Annex A gives the outlet connection type test procedures.Requirements for cylinder valves (see ISO 10297

28、) are not covered by this International Standard.Requirements for material specifications and gas/material compatibility (see ISO 11114-1 and ISO 11114-2) are not covered by this International Standard.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in

29、this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions

30、without individual tolerance indications3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1working pressuresettled pressure of a compressed gas at a uniform reference temperature of 15 C in a full gas cylinderSOURCE: ISO 10286:2007, definition A.2.

31、83.2SCUBAself-contained underwater breathing apparatus3.3compressed breathable airgas which has the nominal composition of atmospheric air and is subject to purity level controls ISO 2013 All rights reserved 1BS EN ISO 12209:2013ISO 12209:2013(E)4 Yoke type outlet connection for SCUBA use up to a ma

32、ximum cylinder working pressure of 232 barFigure 1 shows an example of the yoke type outlet connection in the assembled state.The valve outlet and o-ring dimensions including minimum shore hardness (HS) are shown in Figure 2 and given in Table 1 and Table 2.The exact form of the o-ring groove is the

33、 responsibility of the manufacturer providing the connection passes the outlet connection type test according to Annex A using an o-ring specified in Table 2.In order to ensure that the yoke does fit over the valve, minimum dimensions are given for the yoke (see Figure 3 and Table 3).No outer dimens

34、ions are given for the yoke. However, the dimensions shall be chosen such that the yoke can resist a torque applied via the screw of 20 Nm without visible permanent deformation of the thread and/or the yoke. In addition, the tests described in Annex A shall be carried out.Unless otherwise specified,

35、 the general tolerances for linear and angular dimensions shall be in accordance with class m of ISO 2768-1.Key1 yoke2 valve outlet3 o-ring4 screwFigure 1 Yoke type connection Assembly drawingFigure 2 Valve outlet dimensions2 ISO 2013 All rights reservedBS EN ISO 12209:2013ISO 12209:2013(E)Table 1 V

36、alve outlet dimensionsSymbol Dimension mmTolerance mmConcentricity mmd1to be specified by the manufacturerd212,67 max. 0,1d317,45 max. 0,1d418,16 0,08 0,1d56,3 0,08 0,3l125,5 max. not applicablel21,0 max. not applicablel31,98 0,35 not applicablel428,58 max. not applicablel522,5 max. not applicable 1

37、20 not applicableTable 2 O-ring dimensions and propertiesSymbol/Property“Small type” “Large type”Dimension mmTolerance mmDimension mmTolerance mmd612,42 0,13 12,37 0,13d71,78 0,08 2,62 0,08HS (90 5) Shore ANOTE 1 The o-ring dimensions are taken from ISO 3601-1 (same as ASTM D2240) and the hardness i

38、s defined in ASTM D2240.NOTE 2 The “small type” o-ring is commonly referred to as “-014” by most o-ring manufacturers. The “large type” o-ring is commonly referred to as “-112” by most o-ring manufacturers.Figure 3 Yoke dimensions ISO 2013 All rights reserved 3BS EN ISO 12209:2013ISO 12209:2013(E)Ta

39、ble 3 Yoke dimensionsSymbolDimension mmTolerance mmSymbolDimension mmTolerance mml126 min. d110 min l22,8 min. d223 min l318,8 min. d331 min l41,52 min. d412,8+020005, 110 5 d517,9 0,055 Threaded type outlet connections up to a maximum cylinder working pressure of 232 bar and 300 bar5.1 General requ

40、irementsThe two outlet connections specified in this clause consist each of a valve outlet, a filling connector and a gas withdrawal connector. Use of the specified filling connectors is essential to ensure the safe use of each connection at its intended working pressure.Basic dimensions for the val

41、ve outlet, connectors and its components are shown on Figures 4, 6, 8, 9, 11 and 13 and are specified in Tables 4, 5, 6, 7, 8 and 9 respectively.Unless otherwise specified, the general tolerances for linear and angular dimensions shall be in accordance with class m of ISO 2768-1.5.2 232 bar threaded

42、 outlet connection5.2.1 GeneralThe outlet connection specified here is intended for use at cylinder working pressures not exceeding 232 bar.5.2.2 232 bar valve outletFigure 4 shows the valve outlet to be used for cylinders with a maximum working pressure of 232 bar and Table 4 specifies its dimensio

43、ns.4 ISO 2013 All rights reservedBS EN ISO 12209:2013ISO 12209:2013(E)Figure 4 232 bar valve outletTable 4 Dimensions of 232 bar valve outletSymbol Dimension mmTolerance mmSymbol Dimension mmTolerance mml110 min. d213+030,l215005 ,d3G 5/8al319+0502,d430 min. l512 d55 max. d120,5 min. d62+10aFor dime

44、nsions of pipe threads, see ISO 228-1.5.2.3 232 bar filling connectionFigure 5 is an assembly drawing of the filling connection to be used for filling cylinders up to a maximum working pressure of 232 bar. ISO 2013 All rights reserved 5BS EN ISO 12209:2013ISO 12209:2013(E)Figure 5 232 bar filling co

45、nnection Assembly drawingFigure 6 shows the individual parts of the filling connector and Table 5 specifies their basic dimensions. The valve outlet is shown in Figure 4.Figure 6 232 bar filling connector ComponentsTable 5 Dimensions of 232 bar filling connectorSymbol Dimension mmTolerance mmSymbol

46、Dimension mmTolerance mml21,9001 ,d317 l3702d412 l420 d616005016,b 15 d720 max. d111,2 d8G 5/8ad22,65 d916+025015,cNOTE The o-ring dimensions are taken from ISO 3601-1 (same as ASTM D2240).aFor dimensions of pipe threads, see ISO 228-1.bThe tolerance is taken from ISO 286 where it is defined as “d11

47、”.cThe tolerance is taken from ISO 286 where it is defined as “B11”.6 ISO 2013 All rights reservedBS EN ISO 12209:2013ISO 12209:2013(E)5.2.4 232 bar gas withdrawal connectionFigure 7 is an assembly drawing of the gas withdrawal connection for valves for use with cylinders with a maximum working pres

48、sure of 232 bar.Figure 7 232 bar gas withdrawal connection Assembly drawingFigure 8 shows the individual components of the gas withdrawal connector and Table 6 specifies their basic dimensions. Figure 4 shows the valve outlet.Table 6 Basic dimensions of 232 bar gas withdrawal connectorSymbol Dimensi

49、on mmTolerance mmSymbol Dimension mmTolerance mml13 d317 l21,9001 ,d412+010,l3702d616005016,bl412 0,3 d720 max. a 15 d8G 5/8ad111,2 d916+025015,cd22,65 NOTE The o-ring dimensions are taken from ISO 3601-1 (same as ASTM D2240).aFor dimensions of pipe threads, see ISO 228-1.bThe tolerance is taken from ISO 286 where it is defined as “d11”.cThe tolerance is taken from ISO 286 where it is defi