EN ISO 6412-3-1996 en Technical Drawings - Simplified Representation of Pipelines - Part 3 Terminal Features of Ventilation and Drainage Systems《技术制图 管道的简化表示法 第3部分 通风和排放系统终端部件(ISO .pdf

《EN ISO 6412-3-1996 en Technical Drawings - Simplified Representation of Pipelines - Part 3 Terminal Features of Ventilation and Drainage Systems《技术制图 管道的简化表示法 第3部分 通风和排放系统终端部件(ISO .pdf》由会员分享，可在线阅读，更多相关《EN ISO 6412-3-1996 en Technical Drawings - Simplified Representation of Pipelines - Part 3 Terminal Features of Ventilation and Drainage Systems《技术制图 管道的简化表示法 第3部分 通风和排放系统终端部件(ISO .pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、CEN EN*ISO*b412- 3 96 3404589 0134562 143 BRITISH STANDARD Technical drawings - Simplified representation of pipelines Part 3. Terminal features of ventilation and drainage systems The European Standard EN IS0 64123 : 1996 has the status of a British Standard ICs 01.100.20 23.040.90 NO COPYING WITHO

2、UT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN IS0 BS 308 : Section 4.8 : 1996 6412-3 : 1996 BS EN IS0 64123 : 1996 Amd. No. The following BSI references relate to the work on this standard Committee reference TDW4 Draft announced in BSI News August 1996 ISBN O 680 26187 6 Committees r

3、esponsible for this British Standard Date Text affected The preparation of this British Standard was entrusted to Technical Committee TDEl4, Engineering drawing practice, upon which the following bodies were represented: Atomic Weapons Establishment British Gas plc British Standards Society Drawing

4、Office Materiai Manufacturers and Dealers Association Electricity Association Gauge and Tools Makers Association WAC Association Institution of Chemical Engineers Institution of Engineering Designers Power Generation Contractors Association Society of British Aerospace Companies Lt. University of Wa

5、rwick This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes int effect on 15 August 1996 O BSI 1996 BS EN IS0 64123 : 1996 Contents Committees responsible National foreword Page Inside front

6、 cover ii Foreword Introduction Specification 1 Scope 2 Normative references 3 Design and representation 4 Simplified representation 2 2 Annex A (ionnative) Bibliography 6 ZA (normative) Normative references to international publications with their relevant European publications 7 O BSI 1996 i CEN E

7、N*ISO*b432- 3 96 3404589 0334565 952 BS EN IS0 64123 : 1996 National foreword This British Standard has been prepared by Technical Committee TDW4 and is the English ianguage version of EN IS0 64123 : 1996 Technical drawings - SirnpliJW representation of pipelines - Part 3: Tmid features of ventilati

8、on and drainage systems, published by the European Committee for Standadzation (GEN). It is identical with IS0 64123 : 1993 published by the International Organization for Standardization (ISO). Cross-references Publication referred to Corresponding British Standard EN IS0 6412-1 : 1994 BS EN IS0 64

9、12 Technical drawings. Sirnpl?d representation of pipelines BS EN IS0 6412-1 : 1995 General rules and orthogond representaticm (Is0 6412-1 : 1989) Compliance with a British Standard does not of itself confer immunity from legal obligations. O BSI 1996 EUROPEAN SIANDARD NO= EUROPENNE EXJROP- NORM EN

10、IS0 64123 April 1996 ICs 01.100.20; 23.040.90 Descriptors: Drawings, technical drawings, graphic methods, pipelines, accessories, graphic symbols English version Technical drawings - Simplined representation of pipelines - Part 3: Terminal features of ventilation and drainage systems (IS0 64123 : 19

11、93) Dessins techniques - Reprsentation simplie de tuyaux et linges de tuyauteries - Partie 3 Accessoires pour les Systemes de ventilation et de drainage Entwassermgsaniagen (IS0 64123: 1993) Technische Zeichnungen - Vereinfachte Darstellung von Rohrleitungen - Teil 3: Zubehrteile fr Lftungs- und (IS

12、0 64123 : 1993) This European Stancl-id was approved by CEN on 199643-02. CEN members are bound to comply with the CEN/CENELEC intenial Regulations which stipuiate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliogr

13、aphical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a

14、CEN member into its own language and notified to the Centrai Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, bce, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain,

15、 Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1060 Brussels O 1996 Copyright reserved to CEN members Ref. No. EN 64123 : 1996 E CEN EN*ISO*b432- 3 96 = 34045

16、89 0334567 725 Page 2 EN IS0 64123 : 1996 Foreword The text of the International Standard from Technical Committee ISOAC 10, Technical drawings, product denition and related documentation, of the international organization for Standardization OSO) has been taken over as a European standard by the Te

17、chnical Board of CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 1996, and coricting national standards shall be withdram at the latest by October 1996. According to the CENKENELEC In

18、ternal Regulations, the national standards organkhons of the following countries are bound to implement this European Stan- Austsia, Belgium, Denmark, Finkuid, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingd

19、om. NOTE. Normative references to International Standards are listed in annex ZA (normative). Introduction The principle of drawing practice is to depict an object to scale using lines. In simplified representations only essential features are shown, preferably in outline form (in order to save time

20、 and effort). The degree of simplification depends on the type of object represented, the scale of the drawing and the purpose of the documentation. Q BSI 1996 CEN EN*IS0*6412- 3 96 3404589 Ol345b8 bbl Page 3 EN IS0 6412-3 : 1996 Technical drawings - Simplified representation of pipelines - Part 3:

21、Terminal features of ventilation and drainage systems 1 Scope This part of IS0 6412 specifies simplified represen- tations used in technical drawings for terminal fea- tures of ventilation and drains in pipeline systems. 2 Normative references The following standards contain provisions which, throug

22、h reference in this text, constitute provisions of this part of IS0 6412. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 6412 are encouraged to investi- gate the possibility of applying the mos

23、t recent edi- tions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 5456-2:-), Technical drawings - Projection methods - Part 2: Orthographic representations. IS0 6412-1:1989, Technical drawings - Simplified representation o

24、f pipelines - Part I: General rules and orthogonal representation. 3 Design and representation The simplified representations shown in clause 4 may be combined with graphical symbols, e.g. for actuators or pipes. General principles and additional graphical symbols are given in IS0 6412-1. 4 Simplifi

25、ed representation See table i. The terminal features listed under numbers 1 to 9 are each shown in two orthographic projection views Cl.1, 2.1, 3.1 etc. are views from the front and 1.2, 2.2, 3.2 etc. are views from above see The terminal feature listed under number 10 applies to directional vanes i

26、n ducts. That in 10.1. shows a bent duct with two vanes and those in 10.2 show T- junction ducts with single vanes in opposing di- rections. IS0 5456-2). 1) To be published. CEN EN*ISO*6412- 3 96 m 3404589 0334569 5T8 Page 4 EN IS0 6412-3 : 1996 Table 1 No. 1 1.1 1.2 2 2.1 2.2 3 3.1 3.2 4 4.1 4.2 5

27、5.1 5.2 6 6.1 6.2 - Description Scupper Scupper with closing device Scupper with smell seal and closing device Air pipe (Goose neck) Wall ventilator cowl Mushroom ventilator NOTE - Where applicable with indication “with screen”. Simplified representation 7 e3 + I I r D /I No. 7 7.1 8 8.1 8.2 9 9.1 9

28、.2 10 10.1 10.2 CEN EN*ISO*b4L2- 3 96 3404589 O334570 2LT Page 5 EN IS0 6412-3 1996 Description Mushroom ventilator with closing device NOTE -Where applicable with indication “with screen“. Fixed ventilator cowl Turnable ventilator cowl Outlet or exhaust Inlet or supply Directional vane within a flo

29、w line (pipe or duct) NOTE - An oblique stroke indicates where the vane is lo- cated and short (parallel) lines drawn at right angles to the oblique stroke indicate the number of vanes. Simplified represetntatlon /+ I w i c r“ CEN EN*ISO*b412- 3 9b 3404589 0134571 15b m Page 6 EN IS0 6412-3 : 1996 A

30、nnex A (informative) Bibliography 13 IS0 128:1982, Technical drawings - General principles of presentation. 2 IS0 5455:1979, Technical drawings - Scales. CEN EN*ISOUb4112- 3 96 3404589 01134572 O92 W Page 7 EN IS0 6412-3 : 1996 Annex ZA (normative) Normative references to international publications

31、with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amen

32、dments to or revisions of any of these publications apply to this European Standard oniy when incorporated in it by amendment or revision, For undated references the latest edition of the publication referred to applies. Publication Yeu Kle EN Year IS0 6412-1 1989 Technical dmwings - Simplif ?-prese

33、ntation EN IS0 6412-1 1994 of pipelines- Part 1: Geneml rules and OruLogOnac .presentation CEN EN*IS0*6412- 3 96 3404589 0334573 T29 M BS EN IS0 6412-3 1996 List of references See national foreword. O BSI 1996 BS EN IS0 BS 308 : Section 4.8 : 1996 6412-3 : 1996 BSI 389ChiswickHighRoad London w4 4AL

34、CEP4 EN*ISO*b412- 3 96 3404589 0134574 9b5 BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A

35、 British standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the Mest

36、 amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone nding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the responsible technical committee, the identity of which can b

37、e found on the inside front cover. Tel 0181 996 9000; Fax: O181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the Wst editions of standards. Buying standards Orders for all BSI, international and foreign standards publica

38、tions should be addressed to Customer Services, Sales Department at Chiswick Tel 0181 996 7000; Fax: 0181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.

39、 Information on standards BSI provides a wide range of information on national, European and international standards through its Iibrary, the Standardhe Database, the BSI Information Technology Service (BrrS) and its Technical Help to Exporters Senice. Contact the Information Department at Chiswick

40、Tel 0181 996 7111; Fax: O181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membership at Chimvick Tel: 0181 996 7002; Fax: O

41、181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the intemational standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extsact may be reproduced, stored in a retrieval syste

42、m or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written pennission from BSI. This does not preclude the he use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If t

43、hese details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the tem may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL ISBN O 680 26187 6 TDw4