DIN EN 16564-2015 Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing milling machines included numerical control (NC CNC) ve.pdf
《DIN EN 16564-2015 Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing milling machines included numerical control (NC CNC) ve.pdf》由会员分享,可在线阅读,更多相关《DIN EN 16564-2015 Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing milling machines included numerical control (NC CNC) ve.pdf(56页珍藏版)》请在麦多课文档分享上搜索。
1、April 2015 Translation by DIN-Sprachendienst.English price group 22No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS
2、73.120; 25.080.20; 25.080.60!%B3c“2311664www.din.deDDIN EN 16564Machines and plants for mining and tooling of natural stone Safety Requirements for bridge type sawing/milling machines, includednumerical control (NC/CNC) versions;English version EN 16564:2014,English translation of DIN EN 16564:2015-
3、04Maschinen und Anlagen zur Gewinnung und Bearbeitung von Naturstein Sicherheit Anforderungen an Brcken-Sge-/Frsmaschinen einschlielich numerischerSteuerungsversionen (NC/CNC);Englische Fassung EN 16564:2014,Englische bersetzung von DIN EN 16564:2015-04Machines et quipements pour lexploitation et lu
4、sinage de pierres naturelles Scurit Prescriptions relatives aux machines scier/fraiseuses de type pont, y compris lesversions commande numrique (NC/CNC);Version anglaise EN 16564:2014,Traduction anglaise de DIN EN 16564:2015-04www.beuth.deDocument comprises 56 pagesIn case of doubt, the German-langu
5、age original shall be considered authoritative.03.15 DIN EN 16564:2015-04 2 A comma is used as the decimal marker. National foreword This standard includes safety requirements. This document (EN 16564:2014) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building mate
6、rial machines Safety”, the secretariat of which is held by DIN. The responsible German body involved in its preparation was the DIN-Normenausschuss Maschinenbau (DIN Standards Committee Mechanical Engineering), Working Committee NA 060-13-11 AA Natursteinmaschinen of Section Bau- und Baustoffmaschin
7、en. Representatives of manufacturers and users of surface finishing machines, and of the employers liability insurance associations contributed to this standard. This standard contains specifications meeting the essential requirements set out in Annex I of the “Machinery Directive”, Directive 2006/4
8、2/EC, and which apply to machines that are either first placed on the market or commissioned within the EEA. This standard serves to facilitate proof of compliance with the essential requirements of that directive. Once this standard is cited in the Official Journal of the European Union, it is deem
9、ed a “harmonized” standard and thus, a manufacturer applying this standard may assume compliance with the requirements of the Machinery Directive (“presumption of conformity”). The European Standards referred to in Clause 2 and in the Bibliography of the EN have been published as the corresponding D
10、IN EN or DIN EN ISO Standards with the same number. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16564 December 2014 ICS 25.080.20; 25.080.60; 73.120 English Version Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing/milling machines, i
11、ncluded numerical control (NC/CNC) versions Machines et quipements pour lexploitation et lusinage de pierres naturelles - Scurit - Prescriptions relatives aux machines scier/fraiseuses de type pont, y compris les versions commande numrique (NC/CNC) Maschinen und Anlagen zur Gewinnung und Bearbeitung
12、 von Naturstein - Sicherheit - Anforderungen an Brcken-Sge-/Frsmaschinen einschlielich numerischer Steuerungsversionen (NC/CNC) This European Standard was approved by CEN on 13 September 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions fo
13、r giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in thre
14、e official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bod
15、ies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, S
16、pain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldw
17、ide for CEN national Members. Ref. No. EN 16564:2014 EEN 16564:2014 (E) 2 Contents Page Foreword . 4 Introduction . 5 1 Scope 6 2 Normative references 6 3 Terms and definitions . 9 4 List of significant hazards 16 5 Safety requirements and/or protective measures 18 5.1 General . 18 5.2 Controls 18 5
18、.2.1 Safety and reliability of control systems 18 5.2.2 Position of controls . 19 5.2.3 Starting . 20 5.2.4 Normal stop 20 5.2.5 Emergency stop . 21 5.2.6 HOLD-TO-RUN Operational stop . 21 5.2.7 Mode selection . 22 5.2.8 Failure of any power supply . 23 5.2.9 Failure of the control circuits . 23 5.3
19、 Protection against mechanical hazards 23 5.3.1 Transport and installation of machine 23 5.3.2 Stability . 23 5.3.3 Tool changing 24 5.3.4 Braking tool spindle 24 5.3.5 Prevention of access to moving parts and devices to minimize the effect of ejected parts of tools or workpieces 25 5.4 Protections
20、against no mechanical hazards 29 5.4.1 Fire 29 5.4.2 Noise . 29 5.4.3 Electrical hazards 29 5.4.4 Ergonomics and handling 30 5.4.5 Lighting . 30 5.4.6 Hydraulic and pneumatic components . 31 5.4.7 Electromagnetic compatibility . 31 5.4.8 Laser radiation . 31 5.4.9 Unintended movements 31 5.4.10 Isol
21、ation 31 5.4.11 Maintenance . 32 6 Information for use 32 6.1 Signals and warning devices . 32 6.2 Marking . 32 6.3 Instruction handbook 33 6.3.1 General . 33 6.3.2 Operators manual . 33 6.3.3 Maintenance manual . 36 Annex A (normative) Test for braking function . 37 Annex B (normative) Rigid guards
22、 on machines Impact test method . 38 DIN EN 16564:2015-04 EN 16564:2014 (E) 3 Annex C (normative) Noise Test Code . 41 Annex ZA (informative) Relationship between this European standard and the essential requirements Of EU Directive 2006/42/EC 53 Bibliography 54 DIN EN 16564:2015-04 EN 16564:2014 (E
23、) 4 Foreword This document (EN 16564:2014) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines - Safety”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of
24、an identical text or by endorsement, at the latest by June 2015 and conflicting national standards shall be withdrawn at the latest by June 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DINEN165642015MACHINESANDPLANTSFORMININGANDTOOLINGOFNATURALSTONESAFETYREQUIREMENTSFORBRIDGETYPESAWINGMILLINGMACHINESINCLUDEDNUMERICALCONTROLNCCNCVEPDF

链接地址:http://www.mydoc123.com/p-672963.html