EN 62148-1-2002 en Fibre Optic Active Components and Devices - Package and Interface Standards Part 1 General and Guidance《光纤有源元件和器件 封装和接口标准 第1部分 总则和指南 IEC 62148-1 2002》.pdf

《EN 62148-1-2002 en Fibre Optic Active Components and Devices - Package and Interface Standards Part 1 General and Guidance《光纤有源元件和器件 封装和接口标准 第1部分 总则和指南 IEC 62148-1 2002》.pdf》由会员分享，可在线阅读，更多相关《EN 62148-1-2002 en Fibre Optic Active Components and Devices - Package and Interface Standards Part 1 General and Guidance《光纤有源元件和器件 封装和接口标准 第1部分 总则和指南 IEC 62148-1 2002》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Fibre optic active components and devices Package and interface standards Part 1: General and guidance The European Standard EN 62 148-1 :2002 has the status of a British Standard ICs 33.180.01 BS EN 62 148- 1 12002 British Standards NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMI

2、TTED BY COPYRIGHT LAW BS EN 62148-112002 National foreword This British Standard is the official English language version of EN 62148-1:2002. It is identical with IEC 62148-1:2002. The UKparticipation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/8

3、6/3, Fibre optic systems and active devices, which has the responsibility to: This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 22 July 2002

4、 - - aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of

5、organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period oftime during the change over from one numberin

6、g system to the other, publications may contain identifiers from both systems. Cros s-r e ferenc es The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standard

7、s Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard

8、does not ofitself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued

9、since publication Amd.No. I Date I Comments O BSI 22 July 2002 ISBN O 580 40076 X EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 62148-1 April 2002 ICs 33.180.01 English version Fibre optic active components and devices - Package and interface standards Part 1 : General and guidance (IEC 62148

10、-1 12002) Composants et dispositifs actifs en fibres optiques - Normes de boitier et dinterface Partie 1 : Gnralits et lignes directrices Aktive Lichtwellenleiter-Bauelemente und -Gerte - Gehuse und Schnittstellennorm Teil 1 : Allgemeines und Leitfaden (CE1 62148-1 12002) (IEC 62148-1 12002) This Eu

11、ropean Standard was approved by CENELEC on 2002-04-01. CENELEC members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical referenc

12、es concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC memb

13、er into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Neth

14、erlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels O 2002

15、 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62148-1:2002 E Page 2 EN 62148-12002 Foreword The text of document 86C/384/FDIS, future edition 1 of IEC 62148-1, prepared by SC 86C, Fibre optic systems and active devices, of IEC

16、TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62148-1 on 2002-04-01. The following dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement - late

17、st date by which the national standards conflicting with the EN have to be withdrawn (dop) 2003-01-01 (dow) 2005-04-01 This standard forms one of a series under the general title: Fibre opfic acfive coponenfs and devices - Package and inferface sfandards. This part 1 of EN 62148 covers general infor

18、mation and includes references, definitions and rules for creating an interface standard. Subsequent parts are sequentially numbered and contain standard interfaces for specific active components and devices. Each part will be added as the interfaces become standardized for international use. Endors

19、ement not i ce The text of the International Standard IEC 62148-1:2002 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60130 (Series) NOTE IEC 60191 (Series) NOTE

20、 IEC 60603 (Series) NOTE IEC 60793 (Series) NOTE IEC 61076 (Series) NOTE IEC 61300 (Series) NOTE Harmonized as EN 60130 (Series) (not modified) Harmonized as EN 60191 (Series) (not modified) Harmonized as EN 60603 (Series) (not modified) Harmonized as EN 60793 (Series) (not modified) Harmonized as E

21、N 61076 (Series) (not modified). Harmonized as EN 61300 (Series) (not modified). O BSI 22 July 2002 Page 3 EN 62148-12002 INTRODUCTION Fibre optic active components and devices are used to convert electrical signals into optical signals or vice versa. The optical performance criteria are generally w

22、ell specified for a number of internationally agreed application areas, for example consulting ITU Recommendations originating in Study Group 15, Opfical and ofher fransporf nefworks. Manufacturers using the standards are responsible for meeting the required performance and/or reliability and qualit

23、y assurance under a recognized scheme. O BSI 22 July 2002 Page 4 EN 62148-12002 FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES - PACKAGE AND INTERFACE STANDARDS - Part 1 : General and guidance 1 Scope This part of IEC 62148 aims to assure interchangeability in physical interfaces between fibre optic acti

24、ve components and devices supplied by different manufacturers, but does not guarantee operation between such devices. This interface standard defines physical interfaces only and no guarantee of performance is implied, nor should it be assumed. 2 Normative references The following referenced documen

25、ts are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 601 91-1, Mechanical sfandardizafion of semiconducfor devices - Parf 1: Prepa

26、rafion of drawings of semiconducfor devices IEC 60794 (all parts), Opfical fibre cables IEC 61754 (all parts), Fibre opfic connecfor inferfaces IS0 11 O1 : 1983, Technical drawings - Geomefrical folerancing - Tolerancing of form, orienfafion, locafion and run-ouf - Generalifies, definifions, symbols

27、, indicafions on drawings 3 Definitions For the purposes of this part of IEC 62148, the following definitions apply. 3.1 base plane plane passing through the lowest plane of the case body that is parallel with the seating plane 3.2 elect ri cal term i n al that part of the fibre optic active compone

28、nt or device primarily used for making an electrical connect ion 3.3 footprint projection of the fibre optic active component or device on the seating plane for mounting purposes NOTE This includes the mounting space on the seating plane as well as positions and sizes of counterpart electrical termi

29、nals and mechanical fixtures. O BSI 22 July 2002 Page 5 EN 62148-12002 3.4 in terchangeabi I i ty feature ensuring that mounting, mating and fixturing is possible for products from different manufacturers 3.5 mechanical fixture features for mounting and fixing the active components and devices on to

30、 the counterpart board 3.6 physical interface mechanical interface of case outline, optical interface, electrical interface, etc. NOTE This also includes assignments of electrical terminals and optical ports 3.7 seating plane reference plane contacting with the case body or electrical terminals for

31、mounting of the active components and devices 4 Classification Fibre optic transceiver modules can be classified into different forms according to the combination of mating types of electrical and optical interfaces. 0 Type 1: fibre optic connector interface with direct solderable type electrical te

32、rminals. 0 Type 2: fibre optic connector interface with plug-in type electrical terminals 0 Type 3: fibre optic pigtail interface with direct solderable type electrical terminals. 0 Type 4: fibre optic pigtail interface with plug-in type electrical terminals. 0 Type 5: module that is not classified

33、into types 1 to 4. NOTE A typical example is a module that has both electrical connectors and non-connector type terminals as an electrical interface, such as a coaxial connector for signal and lead terminals for the power supply. 5 Specifications of optical interfaces 5.1 General The optical interf

34、ace should be selected from those whose interchangeability is guaranteed by other IEC standards (for example, IEC 61754). 5.2 Optical connector interfaces (types 1, 2 and 5) Detailed drawings of the optical connector interface are not necessarily required when referenced to the appropriate IEC stand

35、ard. Where an optical connector is not standardized under the IEC system, full detail drawings of the interface shall be presented. 5.3 Pigtail interfaces (types 3, 4 and 5) As a general rule, optical fibres and cables specified in IEC 60794 shall be used for the pigtail interface. O BSI 22 July 200

36、2 Page 6 EN 62148-12002 5.4 Optical port assignments Where an optical port assignment is necess ry to differ ntiat the re eiving and tra smitting elements for the transceiver they should be identified and tabulated. 6 Specifications of electrical interfaces 6.1 General The electrical interface shoul

37、d be selected from those whose interchangeability is guaranteed by other IEC standards (for example, IEC 60130, IEC 60191, IEC 60603, IEC 60807, IEC 61076, etc.) 6.2 Electrical connector interfaces (types 2 and 4) As a general rule, electrical connectors used for the electrical interface of the fibr

38、e optic transceiver module should be those standardized in IEC 60130, IEC 60191, IEC 60603, IEC 60807 and IEC 61076. Detailed drawings of the electrical connector interface are not necessarily required when referenced to the appropriate IEC standard. However, the mechanical datum necessary to guaran

39、tee interchangeability shall be specified in the drawings. Where an electrical connector is not standardized under the IEC system, full detail drawings of the interface shall be presented. 6.3 Non-connector type interfaces (types 1 and 3) As a general rule, non-connector type interfaces used as the

40、electrical interface for the fibre optic transceiver module should be those specified in IEC 60191. In this case, detailed drawings of the electrical interface are not necessarily required when referenced to the appropriate IEC standard. However, the mechanical datum necessary to guarantee interchan

41、geability shall be specified in the drawings. Where an electrical interface is not standardized under the IEC system, the electrical interface shall be specified as complying with the requirements of IEC 60191-1. Numbering of electrical terminals Electrical terminals of the non-connector type interf

42、ace should be identified by numbers according to the system specified in IEC 60191. Electrical terminals of the connector type shall be numbered using the system appropriate to the connector and associated IEC reference. In general, this will involve the use of letters for rows and numbers for pins

43、along the rows. 6.4 Electrical terminal assignment Each electrical pin shall have its functionality (e.g. power, ground, data, etc.) assigned and tabulated in a supplementary table according to the electrical terminal number. 7 Outline and footprint of active components and devices 7.1 Drawings of c

44、ase outline The case outline of the active components and devices in subsequent parts of IEC 62148 shall be presented and interpreted as complying with the requirements described in IS0 1101. O BSI 22 July 2002 Page 7 EN 62148-12002 7.2 Drawings of footprint The footprint of the active components an

45、d devices in subsequent parts of IEC 62148 shall be presented and interpreted as complying with the drawing requirements described in IS0 1101. 7.3 Mechanical fixturing Where mechanical features associated with fixing active components and devices to the board are present on the module, their positi

46、ons and dimensions should be specified in the drawings. Their values and tolerances should be tabulated. These dimensions and tolerances must be consistent with those of the footprint. O BSI 22 July 2002 Page 8 EN 62148-12002 Bibliograph y IEC 60130 (all parts), Connecfors for frequencies below 3 MH

47、z IEC 601 91 (all parts), Mechanical sfandardizafion of semiconducfor devices IEC 60603 (all parts), Connecfors for frequencies below 3 MHz for use wifh prinfed boards IEC 60793 (all parts), Opfical fibres IEC 60807 (all parts), Recfangular connecfors for frequencies below 3 MHz IEC 60874 (all parts

48、), Connecfors for opfical fibres and cables IEC 61076 (all parts), Connecfors wifh assessed qualify, for use in d.c., low frequency analogue and in digifal high speed dafa applicafions IEC 61300 (all parts), Fibre opfic inferconnecfing devices and passive componenfs - Basic fesf and measuremenf proc

49、edures O BSI 22 July 2002 Page 9 EN 62148-12002 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated refe