EN 50307-2002 en Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables《铅和铅合金 电缆的铅和铅合金护套和套管》.pdf

《EN 50307-2002 en Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables《铅和铅合金 电缆的铅和铅合金护套和套管》.pdf》由会员分享，可在线阅读，更多相关《EN 50307-2002 en Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables《铅和铅合金 电缆的铅和铅合金护套和套管》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 50307:2002 Lead and lead alloys Lead and lead alloy sheaths and sleeves of electric cables The European Standard EN 50307:2002 has the status of a British Standard ICS 77.150.60 BS EN 50307:2002 This British Standard was published under the authority of the Standards Policy an

2、d Strategy Committee on 4 April 2003 BSI 4 April 2003 ISBN 0 580 41557 0 National foreword This British Standard is the official English language version of EN 50307:2002. It supersedes BS 801:1984 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee GEL/2

3、0, Electric cables, to Subcommittee GEL/20/16, Medium/high voltage electric cables, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European

4、publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all th

5、e necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on th

6、e interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover

7、and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 50307 NORME EUROPENNE EUROPISCHE NORM December 2002 CENELEC European Committee for Electrotechnical Standard

8、ization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 50307:2002 E

9、ICS 77.150.60 English version Lead and lead alloys Lead and lead alloy sheaths and sleeves of electric cables Plomb et alliages de plomb Gaines et manchons en plomb et alliage de plomb des cbles lectriques Blei und Bleilegierungen Mntel und Metallgehuse von Kabeln aus Blei und Bleilegierungen This E

10、uropean Standard was approved by CENELEC on 2002-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refere

11、nces concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC me

12、mber into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg,

13、Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. EN 50307:2002 - 2 - Foreword This European Standard was prepared by the Technical Committee CENELEC TC 20, Electric cables. The text of the draft was submitted to the formal vote and was approved by CENELE

14、C as EN 50307 on 2002-10-01. The following dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2003-10-01 - latest date by which the national standards conflicting with the EN have to be with

15、drawn (dow) 2005-10-01 Users of this European Standard should note that it covers the chemical composition of lead and lead alloy cable sheaths or sleeves after application or forming. CEN has issued a European Standard (EN 12548) to cover lead and lead alloy ingots for use in the manufacture of cab

16、le sheaths or sleeves. The compositional requirements therein apply to the material prior to manufacture of the cable sheaths or sleeves and melting loss of some of the alloying elements may occur during processing. Annexes designated “normative“ are part of the body of the standard. Annexes designa

17、ted “informative“ are given for information only. In this standard, Annex A and Annex B are informative. _ - 3 - EN 50307:2002 Contents 1 Scope. 4 2 Normative references. 4 3 Definitions 4 4 Designation 4 5 Ordering information for sheaths and sleeves 4 6 Requirements. 5 7 Sampling 5 8 Analysis meth

18、ods . 5 9 Re-test procedure 5 10 Rounding of analysis results 6 11 Inspection documentation for electric cable sheathing and sleeves . 6 12 Marking and labelling of sheathing and sleeves . 7 Annex A (informative) Cross-references between alloy designations . 10 Annex B (informative) Use of lead and

19、lead alloys for cable applications . 11 Table 1 - Chemical composition of lead and lead alloys in electric cable sheaths and sleeves. 8 Table A.1 10 Table B.1 - End-use application - Installation type 11 Table B.2 - End-use application - Functional requirements 12 EN 50307:2002 - 4 - 1 Scope This Eu

20、ropean Standard specifies the designations, chemical compositions and other requirements for lead and lead alloy electric cable sheaths and sleeves. 2 Normative references This European Standard incorporates by dated and undated references, provisions from other publications. These normative referen

21、ces are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this CENELEC Standard only when incorporated in it by amendment or revision. For undated references the lat

22、est edition of the publication referred to applies (including amendments). EN 12548 Lead and lead alloys - Lead alloy ingots for electric cable sheathing and for sleeves 3 Definitions For the purpose of this standard the following definitions apply. 3.1 electric cable sheath uniform and continuous t

23、ubular metallic covering, generally extruded and generally of a circular cross section, encasing one or more insulated electrical conductors in order to contain an impregnant if present, mechanically protect the insulation, to prevent the ingress of moisture and to act as an electrical screen 3.2 sl

24、eeve short length of sheath which may be used in the jointing of some types of electric cables 4 Designation Lead and lead alloys to this standard are designated by an alphanumeric system, see Table 1. The first letter P signifies lead and lead alloys, the second letter K signifies cables. The three

25、 numbers indicate a specific and unique composition for cable sheaths and sleeves, the third letter S signifies sheath (or sleeve). 5 Ordering information for sheaths and sleeves In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and supplier for the

26、 supply of lead and lead alloy cable sheaths or sleeves, the purchaser shall state on the enquiry and order the following information: a) the denomination (e.g. sheath or sleeves); b) the number of this European Standard; c) the material designation (see Table 1); - 5 - EN 50307:2002 d) whether chem

27、ical analysis tests are required; e) whether a certificate of analysis tests or a declaration of conformity is required (see Clause 11); f) whether some form of identifier is required for sleeves (see Clause 11); g) in the case of sleeves, the number, length and dimensions. NOTE The tolerances on le

28、ngth, and other dimensions are to be agreed between the purchaser and the supplier at the time of enquiry or ordering. 6 Requirements 6.1 Chemical composition of sheaths and sleeves The chemical composition of the sheaths or sleeves shall conform to the requirements given in Table 1. 6.2 Freedom fro

29、m defects The sheaths and sleeves shall be free of any defects, damage or contamination liable to adversely affect their intended purpose or service life. 7 Sampling Sampling of sheaths or sleeves for chemical analysis shall be in accordance with the requirements of the product specification. 8 Anal

30、ysis methods When analysis is carried out to verify conformity of sheaths and sleeves to this standard the analytical methods used shall be at the discretion of the supplier. In cases of dispute concerning the results of analysis and pending the publication of a suitable European Standard containing

31、 analytical methods (in preparation by CEN), the methods of analysis shall be agreed between the disputing parties. For expression of the results of chemical analysis the rounding rules given in Clause 10 shall be used. 9 Re-test procedure Should any sample fail to meet the specified requirements in

32、 6.1, two further samples shall be taken from the same sheath or batch of sleeves and subjected to the same test or tests in which the original sample failed. Should both additional test samples pass the test, all the cables or sleeves in the batch from which they were taken shall be regarded as com

33、plying with the requirements of this specification. Should either of them fail, the batch from which the samples were representative shall be regarded as failing to comply. Further re-sampling and testing shall be subject to agreement between the supplier and customer. EN 50307:2002 - 6 - 10 Roundin

34、g of analysis results For the purposes of determining conformity to the compositional requirements of this standard, an observed or a calculated value obtained during analysis shall be rounded in accordance with the following procedure. It shall be rounded in one step to the same number of figures u

35、sed to express the specified limit in Table 1. The following rules shall be used for rounding: a) if the figure immediately after the last figure to be retained is less than five, the last figure to be retained shall be kept unchanged; b) if the figure immediately after the last figure to be retaine

36、d is equal to or greater than five, the last figure to be retained shall be increased by one. 11 Inspection documentation for electric cable sheathing and sleeves If requested by the purchaser at the time of ordering, the supplier shall provide inspection documents with each consignment of cables or

37、 sleeves. The documentation shall be as chosen by the purchaser and shall be in accordance with either a) or b) as follows: a) a certificate of analysis, giving the results obtained on the specific batches in the consignment. This certificate shall also include the following information: 1) name and

38、 address of supplier; 2) date of certificate of analysis; 3) name and address of purchaser; 4) purchasers contract, or order, number; 5) a description of the goods and the quantity supplied; 6) details of the specification and alloy designation of the sheathing supplied; 7) signature of suppliers au

39、thorised representative. b) a declaration of conformity of the consignment with the order requirements. This declaration shall include the following information: 1) name and address of supplier; 2) date of declaration of conformity; 3) name and address of purchaser; 4) purchasers contract, or order,

40、 number; 5) a description of the goods and the quantity supplied; 6) details of the specification and alloy designation of the sheathing supplied; and - 7 - EN 50307:2002 7) the following declaration: The goods detailed hereon have been manufactured to conform to the requirements of the purchasers o

41、rder and to the description, quantity and specification detailed thereon. Signed: (Suppliers authorised representative) 12 Marking and labelling of sheathing and sleeves 12.1 Cable sheathing The identification of electric cable sheathing is not a requirement of this specification but shall be in acc

42、ordance with the requirements of the product standard. 12.2 Sleeves If requested at the time of enquiry or order, the sleeves shall be identified in a manner agreed between the supplier and the purchaser. The identification shall provide the following minimum information: a) the manufacturers name,

43、trade or identification mark; b) the number and year of this European Standard : EN 50307:2002; c) the material designation. EN 50307:2002 - 8 -Table 1 - Chemical composition of lead and lead alloys in electric cable sheaths and sleeves Compositions in % (m/m) Alloy Element Alloying elements Impurit

44、ies designation a As Bi Ca Cd Cu Sb Sn Te Pb Ag As Bi Cd Cu Ni Sb Sn Te Zn PK900S min. max. - - - - - - - - - - - - - - - - 99,90 - - 0,008 - 0,005 - 0,06 - 0,005 - 0,005 - 0,002 - 0,003 - 0,02 - 0,002 - 0,001 PK001S min. max. - - - - - - - - - - 0,80 0,95 - - - - Rem - 0,005 - 0,005 - 0,05 - 0,001

45、- 0,003 - 0,001 - - - 0,01 - 0,002 - 0,0005 PK002S min. max. - - - - - - - - - - 0,50 0,60 - - - - Rem - 0,005 - 0,005 - 0,05 - 0,001 - 0,003 - 0,001 - - - 0,005 - 0,002 - 0,0005 PK008S * min. max. - - - - - - - - - - 0,45 0,55 - - - - Rem - 0,003 - 0,003 - 0,02 - 0,001 - 0,003 - 0,001 - - - 0,003 -

46、 0,002 - 0,001 PK009S * min. max. - - - - - - - - - - 0,5 1,0 - - - - Rem - 0,003 - 0,001 - 0,05 - - - 0,005 - - - - - 0,005 - - - 0,001 PK011S min. max. - - - - - - 0,14 0,16 - - - - 0,35 0,45 - - Rem - 0,0025 - 0,001 - 0,015 - 0,003 - 0,0005 - 0,003 - - - 0,002 - 0,0005 PK012S min. max. - - - - -

47、- 0,06 0,09 - - - - 0,17 0,23 - - Rem - 0,0025 - 0,001 - 0,015 - 0,003 - 0,0005 - 0,003 - - - 0,002 - 0,0005 PK021S min. max. - - - - - - - - - - 0,15 0,25 0,35 0,45 - - Rem - 0,005 - 0,001 - 0,03 - 0,001 - 0,003 - 0,001 - - - - - 0,002 - 0,0005 PK022S min. max - - - - - - - - - - 0,06 0,10 0,35 0,4

48、5 - - Rem - 0,005 - 0,001 - 0,03 - 0,001 - 0,003 - 0,001 - - - - - 0,002 - 0,0005 PK023S min. max. - - - - - - - - - - 0,08 0,12 0,17 0,23 - - Rem - 0,005 - 0,001 - 0,03 - 0,001 - 0,003 - 0,001 - - - - - 0,002 - 0,0005 PK031S min. max. 0,15 0,18 0,08 0,12 - - - - - - - - 0,10 0,13 - - Rem - 0,0025 -

49、 - - - - 0,0005 - 0,003 - 0,0005 - 0,003 - - - 0,002 - 0,0005 PK032S min. max. 0,07 0,09 0,04 0,06 - - - - - - - - 0,05 0,07 - - Rem - 0,0025 - - - - - 0,0005 - 0,003 - 0,0005 - 0,003 - - - 0,002 - 0,0005 PK041S min. max - - - - - - - - 0,030 0,045 - - - - 0,035 0,045 Rem - 0,005 - 0,001 - 0,03 - 0,001 - - - 0,0010 - 0,001 - 0,02 - - - 0,0005 PK042S min. max. - - - - - - - - 0,014 0,020 - - - - 0,014 0,020 Rem - 0,0025 - 0,001 - 0,015 - 0,001 - - - 0,0005 - 0,001 - 0,02 - - - 0,0