EN 60079-7-2015 en Explosive atmospheres - Part 7 Equipment protection by increased safety e .pdf

《EN 60079-7-2015 en Explosive atmospheres - Part 7 Equipment protection by increased safety e .pdf》由会员分享，可在线阅读，更多相关《EN 60079-7-2015 en Explosive atmospheres - Part 7 Equipment protection by increased safety e .pdf（130页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationExplosive atmospheresPart 7: Equipment protection by increased safety “e”BS EN 60079-7:2015National forewordThis British Standard is the UK implementation of EN 60079-7:2015. It isidentical with IEC 60079-7:2015. It supersedes BS EN 60079-7:2007, which iswithdrawn. It partia

2、lly supersedes BS EN 60079-15:2010, specifically therequirements for Type of Protection “nA”.The significance of the changes between this standard (for “ec”) and BSEN 60079-15:2010 (for “nA”) are listed in a table in Annex ZY. The majortechnical changes include:- Soldered Connections- Thermal stabil

3、ity of solid insulating materials- Addition of end-of-life tests- Ex Component enclosures Where a requirement of this standard conflicts with a requirement of BS EN 60079-15:2010, the requirement of this standard takes precedence.The UK participation in its preparation was entrusted to TechnicalComm

4、ittee EXL/31, Equipment for explosive atmospheres.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British St

5、andards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 82073 1ICS 29.260.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2015

6、.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60079-7:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60079-7 December 2015 ICS 29.260.20 Supersedes EN 60079-7:2007 English Version Explosive atmospheres - Part 7: Equipment protection by increased saf

7、ety “e“ (IEC 60079-7:2015) Atmosphres explosives - Partie 7: Protection de lquipement par scurit augmente “e“ (IEC 60079-7:2015) Explosionsfhige Atmosphre - Teil 7: Gerteschutz durch erhhte Sicherheit “e“ (IEC 60079-7:2015) This European Standard was approved by CENELEC on 2015-07-31. CENELEC member

8、s are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application

9、 to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC M

10、anagement Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland,

11、 Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europische

12、s Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60079-7:2015 E BS EN 60079-7:2015EN 60079-7:2015 (E) 2 European foreword Th

13、e text of document 31/1182/FDIS, future edition 5 of IEC 60079-7, prepared by IEC/TC 31 “Equipment for explosive atmospheres“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60079-7:2015. The following dates are fixed: latest date by which the document has to be implemen

14、ted at national level by publication of an identical national standard or by endorsement (dop) 2016-06-11 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-07-31 This document supersedes EN 60079-7:2007. Attention is drawn to the possibility th

15、at some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Associ

16、ation, and supports essential requirements of EU Directive(s). For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this document. Endorsement notice The text of the International Standard IEC 60079-7:2015 was approved by CENELEC as a European Standard wit

17、hout any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC/TS 60034-17 NOTE Harmonized as CLC/TS 60034-17. IEC 60034-18-41 NOTE Harmonized as EN 60034-18-41. IEC/TS 60034-25 NOTE Harmonized as CLC/TS 60034-25. IEC 60079-14

18、NOTE Harmonized as EN 60079-14. IEC 60079-17 NOTE Harmonized as EN 60079-17. IEC 60079-18 NOTE Harmonized as EN 60079-18. IEC 60079-20-1 NOTE Harmonized as EN 60079-20-1. IEC 60079-28 NOTE Harmonized as EN 60079-28. IEC 60079-29-2 NOTE Harmonized as EN 60079-29-2. IEC 60079-30-2 NOTE Harmonized as E

19、N 60079-30-2. IEC 60079-35-1 NOTE Harmonized as EN 60079-35-1. IEC 60086-1 NOTE Harmonized as EN 60086-1. IEC 60095-1 NOTE Harmonized as EN 60095-1. IEC 60364-5-55 NOTE Harmonized in EN 60364-5-55 series. IEC 60622 NOTE Harmonized as EN 60622. IEC 60623 NOTE Harmonized as EN 60623. IEC 60664-3 NOTE

20、Harmonized as EN 60664-3. BS EN 60079-7:2015EN 60079-7:2015 (E) 3 IEC 60927 NOTE Harmonized as EN 60927. IEC 61008-1 NOTE Harmonized as EN 61008-1. IEC 61056-1 NOTE Harmonized as EN 61056-1. IEC 61347-2-1 NOTE Harmonized as EN 61347-2-1. IEC 61347-2-4 NOTE Harmonized as EN 61347-2-4. IEC 61347-2-7 N

21、OTE Harmonized as EN 61347-2-7. IEC 61347-2-8 NOTE Harmonized as EN 61347-2-8. IEC 61347-2-9 NOTE Harmonized as EN 61347-2-9. IEC 61347-2-13 NOTE Harmonized as EN 61347-2-13. IEC 61951-1 NOTE Harmonized as EN 61951-1. IEC 62013-1 NOTE Harmonized as EN 62013-1. ISO 13849-1 NOTE Harmonized as EN ISO 1

22、3849-1. BS EN 60079-7:2015EN 60079-7:2015 (E) 4 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application.

23、For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 U

24、p-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year IEC 60034-1 - Rotating electrical machines - Part 1: Rating and performance EN 60034-1 - IEC 60044-6 - Instrument transformers - Part 6: Req

25、uirements for protective current transformers for transient performance EN 60044-6 - IEC 60061-1 - Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps EN 60061-1 - IEC 60061-2 - Lamp caps and holders together with gauges for the control of

26、interchangeability and safety - Part 2: Lampholders EN 60061-2 - IEC 60064 - Tungsten filament lamps for domestic and similar general lighting purposes - Performance requirements EN 60064 - IEC 60068-2-6 - Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) EN 60068-2-6 - IEC 6

27、0068-2-27 2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock EN 60068-2-27 2009 IEC 60068-2-42 - Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections EN 60068-2-42 - IEC 60079-0 - Explosive atmospheres - Part 0: Equipment - Ge

28、neral requirements EN 60079-0 - IEC 60079-1 - Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures “d“ EN 60079-1 - IEC 60079-11 - Explosive atmospheres - Part 11: Equipment protection by intrinsic safety “i“ EN 60079-11 - IEC 60079-30-1 - Explosive atmospheres - Part 30-1:

29、Electrical resistance trace heating - General and testing requirements EN 60079-30-1 - IEC 60085 - Electrical insulation - Thermal evaluation and designation EN 60085 - IEC 60112 - Method for the determination of the proof and the comparative tracking indices of solid insulating materials EN 60112 -

30、 IEC 60216-1 - Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results EN 60216-1 - BS EN 60079-7:2015EN 60079-7:2015 (E) 5 IEC 60216-2 - Electrical insulating materials - Thermal endurance properties - Part 2: Determination of therma

31、l endurance properties of electrical insulating materials - Choice of test criteria EN 60216-2 - IEC 60228 - Conductors of insulated cables EN 60228 - IEC 60238 - Edison screw lampholders EN 60238 - IEC 60317-3 +A1 2004 2010 Specifications for particular types of winding wires - Part 3: Polyester en

32、amelled round copper wire, class 155 - - IEC 60317-8 - Specifications for particular types of winding wires - Part 8: Polyesterimide enamelled round copper wire, class 180 EN 60317-8 - IEC 60317-13 - Specifications for particular types of winding wires - Part 13: Polyester or polyesterimide overcoat

33、ed with polyamide-imide enamelled round copper wire, class 200 EN 60317-13 - IEC 60317-46 - Specifications for particular types of winding wires - Part 46: Aromatic polyimide enamelled round copper wire, class 240 EN 60317-46 - IEC 60400 - Lampholders for tubular fluorescent lamps and starterholders

34、 EN 60400 - IEC 60432-1 - Incandescent lamps - Safety specifications - Part 1: Tungsten filament lamps for domestic and similar general lighting purposes EN 60432-1 - IEC 60432-2 - Incandescent lamps - Safety specifications - Part 2: Tungsten halogen lamps for domestic and similar general lighting p

35、urposes EN 60432-2 - IEC 60432-3 - Incandescent lamps - Safety specifications - Part 3: Tungsten halogen lamps (non-vehicle) EN 60432-3 - IEC 60529 - Degrees of protection provided by enclosures (IP Code) - - IEC 60598-1 - Luminaires - Part 1: General requirements and tests EN 60598-1 - IEC 60664-1

36、- Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests EN 60664-1 - IEC 60947-1 - Low-voltage switchgear and controlgear - Part 1: General rules EN 60947-1 - IEC 60947-7-1 - Low-voltage switchgear and controlgear - Part 7-1: Ancillary equipmen

37、t - Terminal blocks for copper conductors EN 60947-7-1 - IEC 60947-7-2 - Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors EN 60947-7-2 - IEC 60947-7-4 - Low-voltage switchgear and controlgear - Part 7-4: Ancillary equ

38、ipment - PCB terminal blocks for copper conductors EN 60947-7-4 - IEC 60998-2-4 - Connecting devices for low voltage circuits for household and similar purposes - Part 2-4: Particular requirements for twist-on connecting devices EN 60998-2-4 - BS EN 60079-7:2015EN 60079-7:2015 (E) 6 IEC 60999-1 - Co

39、nnecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm up to 35 mm (included) EN 60999-1 - IEC 60999-2 - Connecting devices - Elect

40、rical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm up to 300 mm (included) EN 60999-2 - IEC 61184 - Bayonet lampholders EN 61184 - IEC 61195 - Double-capped fluorescent lamps -

41、 Safety specifications EN 61195 - IEC 61347-1 - Lamp controlgear - Part 1: General and safety requirement EN 61347-1 - IEC 61347-2-3 - Lamp controlgear - Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps EN 61347-2-3 - IEC 62035 - Discharge

42、 lamps (excluding fluorescent lamps) - Safety specifications EN 62035 - ISO 178 - Plastics - Determination of flexural properties EN ISO 178 - ISO 527-2 - Plastics - Determination of tensile properties Part 2: Test conditions for moulding and extrusion plastics EN ISO 527-2 - ISO 2859-1 - Sampling p

43、rocedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection - - BS EN 60079-7:2015EN 60079-7:2015 (E) 7 Annex ZZ (informative) Relationship between this European standard and the essential requirements of Directive 94/9/EC aim

44、ed to be covered This European standard has been prepared under a Commissions standardisation request to provide one voluntary means of conforming to essential of Directive 94/9/EC of the European Parliament and the Council of 23 March 1994 on the approximation of the laws of the Member States conce

45、rning equipment and protective systems intended for use in potentially explosive atmospheres. Once this standard is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of the s

46、cope of this standard, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. Table ZZ.1 Correspondence between this European standard and Annex II of Directive 94/9/EC Essential Requirements of Directive Clause(s) / sub-clause(s

47、) of this EN Remarks / Notes 1.0.1. All clauses This is the purpose of the Standard. 1.0.2. 4.2 / 4.4 / 4.6 / 5.2 / 5.3 / 5.4 / 5.6 / 5.8 / 5.9 / A.3 / A.5 / B.4.2 1.0.3. 5.2 / 5.3 / 5.6 1.0.4. 4.2 / 4.6 / 4.8 1.0.5. 5.2 / 5.3 / 5.7 / 5.9 / 8.1 / 8.2 / 9.4 1.0.6. 5.7 / 8.2 1.1.1. 5.6 / 4.2 1.1.2. 4.

48、6 / 4.7 / 5.2 / 5.3 / 5.6 / 6.6 1.1.3. 4.2 / 4.3 / 4.9 / 5.2 / 5.3 / 5.6 / 5.8 / 6.1 / 6.6 / 6.7 / 6.8 / 7 1.2.1. All All clauses of the standard contain up-to-date requirements 1.2.2. 5.3 / 5.6 / 5.9 1.2.3. 5.6 / 6.6 / 6.7 1.2.4. Not covered 1.2.5. 4.10 / 5.3 / B.1 1.2.6. 4.11 1.2.7. 4.8 / 5.6 / B.

49、4 BS EN 60079-7:2015EN 60079-7:2015 (E) 8 1.2.8. 5.2 / 5.3 / 5.6 / 5.8 / 5.9 1.2.9. Not covered 1.3.1. 4.2 / 4.4 / 4.6 / 5.3 / 5.6 / 6.8 1.3.2. Not covered 1.3.3. 4.4 / 5.3 / 5.6 1.3.4. 5.2 1.3.5. Not covered 1.4.1. 4.2 / 4.11 5.3 / 6.2 / 6.3 / 6.4 1.4.2. 4.2 / 4.3 / 4.6 / 4.9 / 5.2 / 5.3 / 5.6 / 5.8 / 6.2 / 6.3 / 6.8 1.5.1 5.2 / 5.8 / 6.2 1.5.2. 5.2 / 5.8 / 6.2 1.5.3. 5.2 / 5.8 / 6.2 1.5.4. 5.2 / 5.8 / 6.2 1.5.5. 5.2 / 5.8 / 6.2 1.5.6