EN 15732-2012 en Light weight fill and thermal insulation products for civil engineering applications (CEA) - Expanded clay lightweight aggregate products (LWA)《土木工程应用(CEA)的轻量填充和隔热.pdf

《EN 15732-2012 en Light weight fill and thermal insulation products for civil engineering applications (CEA) - Expanded clay lightweight aggregate products (LWA)《土木工程应用(CEA)的轻量填充和隔热.pdf》由会员分享，可在线阅读，更多相关《EN 15732-2012 en Light weight fill and thermal insulation products for civil engineering applications (CEA) - Expanded clay lightweight aggregate products (LWA)《土木工程应用(CEA)的轻量填充和隔热.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationLight weight fill and thermal insulation products for civil engineering applications (CEA) Expanded clay lightweight aggregate products (LWA)BS EN 15732:2012BS EN 15732:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 15732:2012.The

2、UK committee voted against the approval of EN 15732 due to duplication of content covered in BS EN 13055-2. Both standards cover the requirements for all types of lightweight aggregate, including expanded clay and for all loose-fill construction applications including civil engineering applications.

3、The users attention is also drawn to several inconsistencies found by UK experts: Clause 4.3.2, the reference to EN 14063-1 for the method to determine the thermal conductivity of expanded clay lightweight aggregate is incorrect, however, users are advised to refer to EN 12664. There is also limited

4、 guidance given on how to obtain design thermal values from such measurement results. Clause 4.3.3, the direction to use EN ISO 10456 to determine specific heat capacity implies that the standard contains a test or calculation method whereas it only gives tabulated values of specific heat. Clause 4.

5、3.8, contains test requirements for loading, which are at variance with those in Annex C to which it refers. Clause 4.3.10, contains test requirements for loading, which are at variance with those in Annex B to which it refers.Annex E, the table in Annex E gives k10,dry values which are inappropriat

6、e for the application. Used below ground, the expanded clay is unlikely to be dry so the values given are too low to be used as design values and therefore, cannot be considered safe.The UK participation in its preparation was entrusted to Technical Committee B/540, Energy performance of materials c

7、omponents and buildings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013

8、. Published by BSI Standards Limited 2013ISBN 978 0 580 77384 6ICS 91.100.60Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2013.Amendments/corrigenda is

9、sued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15732 October 2012 ICS 91.100.60 English Version Light weight fill and thermal insulation products for civil engineering applications (CEA) - Expanded clay lightweight aggregate products (LWA) Matriaux de re

10、mplissage lgers et produits isolants thermiques pour les applications du gnie civil - Produits base de granulats lgers dargile expanse Leichte Schtt- und Wrmedmmstoffe fr bautechnische Anwendungen (CEA) - Produkte aus Blhton-Leichtzuschlagstoffen (LWA) This European Standard was approved by CEN on 9

11、 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may

12、 be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified t

13、o the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland,

14、 Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Av

15、enue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15732:2012: EBS EN 15732:2012EN 15732:2012 (E) 2 Contents Page Foreword 41 Scope 52 Normative references 53 Terms definitions, symbols, units and

16、abbreviated terms 63.1 Terms and definitions .63.2 Symbols, units and abbreviated terms 64 Requirements .74.1 General 74.2 For all applications 74.3 For specific applications .84.4 Other requirements. 105 Test methods . 105.1 Sampling 105.2 Conditioning 105.3 Testing . 106 Designation code 117 Evalu

17、ation of conformity 127.1 General 127.2 Initial type testing 127.3 Factory production control . 128 Marking and labelling . 12Annex A (normative) Test for mechanical and physical properties of expanded clay LWA Static Triaxial Compression Test for determination of shear strength properties . 13A.1 G

18、eneral . 13A.2 Definitions, symbols and abbreviations . 13A.3 Test principle . 14A.3.1 Triaxial apparatus . 14A.3.2 Loading device 14A.3.3 Confining pressure and vacuum-control device . 14A.3.4 Displacement transducers . 15A.3.5 Calibration . 15A.3.6 Top cap and pedestal . 16A.3.7 Porous discs . 16A

19、.4 Testing procedure. 18A.4.1 Number of test specimens . 18A.4.2 Procedures for compaction of laboratory test specimens . 18A.4.3 Compaction using vibrations 18A.4.4 Other means of compaction 18A.5 Test report . 18Annex B (normative) Test for mechanical and physical properties of expanded clay LWA D

20、etermination of the resistance to cyclic compressive loading . 19B.1 General . 19B.2 Definitions . 19B.3 Sampling 19B.4 Test method . 19B.4.1 General . 19B.4.2 Principle . 19B.4.3 Equipment . 19BS EN 15732:2012EN 15732:2012 (E) 3 B.4.4 Preparation of test specimens . 21B.4.5 Test procedure . 21B.4.6

21、 Calculations . 23B.4.7 Expression of the test results 23B.5 Report . 23Annex C (normative) Test for mechanical and physical properties of expanded clay LWA Determination of the compressive creep 25C.1 General . 25C.2 Principles 25C.3 Equipment 25C.4 Preparation of test specimens . 27C.5 Testing 27C

22、.5.1 Test procedure . 27C.5.2 Calculations . 28C.5.3 Expression of results 28C.6 Report . 28Annex D (normative) Factory production control 30Annex E (informative) Tabulated 10,dry-values of expanded clay LWA in lightweight fill applications 31Annex ZA (informative) Clauses of this European Standard

23、addressing the provisions of the EU Construction Products Directive . 32BS EN 15732:2012EN 15732:2012 (E) 4 Foreword This document (EN 15732:2012) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European St

24、andard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention is drawn to the possibility that some of the elements of th

25、is document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential req

26、uirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This standard is the harmonised part satisfying the mandate, the CPD and is the basis for the CE marking, covers the products which are placed on the market. Acc

27、ording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, German

28、y, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 15732:2012EN 15732:2012 (E) 5 1 Scope This European Standard describes the product c

29、haracteristics and includes procedures for testing, marking and labelling. This standard specifies the requirements for loose-fill expanded clay lightweight aggregate (expanded clay LWA) products for Civil Engineering Applications excluding the use as thermal insulation in and under buildings which

30、are covered by EN 14063-1. The standard covers the use of expanded clay LWA as lightweight fill and insulation materials in embankments for roads, railways and other trafficked areas and as lightweight backfill for structures. This standard does not specify the required level of a given property to

31、be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards. 2 Normative references The following documents, in whole or in part, are normatively referenced in this do

32、cument and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 932-1, Tests for general properties of aggregates Part 1: Methods for sampling EN 932-2

33、, Tests for general properties of aggregates Part 2: Method for reducing laboratory samples EN 933-1, Tests for geometrical properties of aggregates Part 1: Determination of particle size distribution Sieving method EN 1097-3, Tests for mechanical and physical properties of aggregates Part 3: Determ

34、ination of loose bulk density and voids EN 1097-5, Tests for mechanical and physical properties of aggregates Part 5: Determination of the water content by drying in a ventilated oven EN 1097-6:2000, Tests for mechanical and physical properties of aggregates Part 6: Determination of particle density

35、 and water absorption EN 13055-1:2002, Lightweight aggregates Part 1: Lightweight aggregates for concrete, mortar and grout EN 13055-2:2004, Lightweight aggregates Part 2: Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications EN 13172:2012, Ther

36、mal Insulation products Evaluation of conformity EN 13286-4, Unbound and hydraulically bound mixtures Part 4: Test methods for laboratory reference density and water content Vibrating hammer EN 13286-5, Unbound and hydraulically bound mixtures Part 5: Test methods for laboratory reference density an

37、d water content Vibrating table EN 13286-7, Unbound and hydraulically bound mixtures Part 7: Cyclic load triaxial test for unbound mixtures EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire test EN 13820, Thermal in

38、sulating materials for building applications Determination of organic content BS EN 15732:2012EN 15732:2012 (E) 6 EN 14063-1, Thermal insulation products for buildings In-situ formed expanded clay lightweight aggregate products Part 1: Specification for the loose-fill products before installation EN

39、 ISO 9229:2007, Thermal insulation Vocabulary (ISO 9229:2007) EN ISO 10456:2007, Building materials and products Hygrothermal properties Tabulated design values and procedures for determining declared and design thermal values (ISO 10456:2007) 3 Terms definitions, symbols, units and abbreviated term

40、s 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 9229:2007, and the following apply. 3.1.1 expanded clay lightweight aggregate insulation material or product composed of lightweight granular material having a cellular structure formed by expand

41、ing clay minerals by heat 3.1.2 compressibility deformation at a certain load of a vibrated specimen, given as a load-deformation curve 3.1.3 compressive strength, CS(10) the load where the deformation of a vibrated specimen is 10 % 3.1.4 stiffness modulus is given as the tangent to the load-deforma

42、tion curve and is related to the level of deformation 3.1.5 compressive creep (CC) the deformation at a constant load in a specified time 3.1.6 compaction mechanical compression (e.g. by vibrator) of the installed insulation layer, expressed as a percentage of the initial untreated layer thickness 3

43、.1.7 level given value, which is the upper or lower limit of a requirement. The level is given by the declared value of the characteristic concerned 3.1.8 class combination of two levels of the same property, between which the performance falls, where the levels are given by the declared value of th

44、e characteristic concerned 3.2 Symbols, units and abbreviated terms Symbols and units used in this standard: LD is the symbol of the declared level for loose bulk density PS is the symbol of the declared level for aggregate size (mm) BS EN 15732:2012EN 15732:2012 (E) 7 CS(10) is the symbol of the de

45、clared level for compressive strength at 10 % deformation CC is the symbol of the declared level for compressive creep Abbreviated terms used in this standard: LWA is Lightweight Aggregate ITT is Initial Type Test CEA is Civil Engineering Applications 4 Requirements 4.1 General Product properties sh

46、all be assessed in accordance with Clause 5. To conform with this standard, products shall meet the requirements of 4.2 and the requirements of 4.3 as appropriate. Sampling of expanded clay LWA shall be performed according to EN 932-1 and splitting of samples according to EN 932-2. One test result o

47、n a product property is the average of the measured values on the number of test specimens given in Table 1. 4.2 For all applications 4.2.1 Loose bulk density Loose bulk density shall be declared and determined in accordance with EN 1097-3. The dry loose bulk density shall be declared by the manufac

48、turer in steps of 5 kg/m3 up to a density of 400 kg/m3 and thereafter in steps of 10 kg/m3. It shall be in the range of 15 % of the manufacturers declared value with a maximum of 100 kg /m3 .The value shall be expressed in kg/m3. NOTE The value of the density used for design purposes will be influenced by compaction and water content. 4.2.2 Particle size distribution 4.2.2.1 General Particle size distribution shall be measured in accordance with EN 933-1, without washing, and shall be declared in % by mass. 4.2.2.2 Aggregate size The pair of sieve sizes between which the