EN 15704-2008 en Liming materials - Determination of the breakdown of granulated calcium and calcium magnesium carbonates under the influence of water《石灰处理材料 水影响下的颗粒状钙和碳酸钙 碳酸镁断裂的测定.pdf

《EN 15704-2008 en Liming materials - Determination of the breakdown of granulated calcium and calcium magnesium carbonates under the influence of water《石灰处理材料 水影响下的颗粒状钙和碳酸钙 碳酸镁断裂的测定.pdf》由会员分享，可在线阅读，更多相关《EN 15704-2008 en Liming materials - Determination of the breakdown of granulated calcium and calcium magnesium carbonates under the influence of water《石灰处理材料 水影响下的颗粒状钙和碳酸钙 碳酸镁断裂的测定.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 15704:2008ICS 65.080NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDLiming materials Determinationof the breakdownof granulatedcalcium and calcium/magnesium carbonatesunder the influence ofwaterThis British Standardwas published under theauthority of the S

2、tandardsPolicy and StrategyCommittee on 31 January2009 BSI 2009ISBN 978 0 580 58989 8Amendments/corrigenda issued since publicationDate CommentsBS EN 15704:2008National forewordThis British Standard is the UK implementation of EN 15704:2008.The UK participation in its preparation was entrusted to Te

3、chnicalCommittee CII/37, Fertilisers and related chemicals.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compli

4、ance with a British Standard cannot confer immunityfrom legal obligations.BS EN 15704:2008EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15704December 2008ICS 65.080English VersionLiming materials - Determination of the breakdown of granulatedcalcium and calcium/magnesium carbonates under the inf

5、luenceof waterAmendements minraux basiques - Dtermination dudlitage leau de carbonates de calcium et carbonates decalcium/magnsium granulsCalcium-/Magnesium-Bodenverbesserungsmittel -Bestimmung des Zerfalls von granulierten Calcium- undCalcium-/Magnesiumcarbonaten unter WassereinwirkungThis European

6、 Standard was approved by CEN on 15 November 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concer

7、ning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own la

8、nguage and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu

9、xembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All righ

10、ts of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15704:2008: EBS EN 15704:2008EN 15704:2008 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principle 4 5 Apparatus .5 6 Reagents .5 7 Procedure .5 8 C

11、alculation 6 9 Precision .6 10 Test report 7 Bibliography 8 BS EN 15704:2008EN 15704:2008 (E) 3 Foreword This document (EN 15704:2008) has been prepared by Technical Committee CEN/TC 260 “Fertilizers and liming materials”, the secretariat of which is held by DIN. This European Standard shall be give

12、n the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2009, and conflicting national standards shall be withdrawn at the latest by June 2009. Attention is drawn to the possibility that some of the elements of this document may be the

13、 subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgiu

14、m, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 15704:2008EN 1

15、5704:2008 (E) 4 1 Scope This European Standard specifies a method for the determination of the break down of granulated calcium and calcium /magnesium carbonates under the influence of water. 2 Normative references The following referenced documents are indispensable for the application of this docu

16、ment. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1482-2, Fertilizers and liming materials Sampling and sample preparation Part 2: Sample preparation EN 12048, Solid fertilizers and

17、 liming materials Determination of moisture content Gravimetric method by drying at (105+/-2) C (ISO 8190:1992 modified) EN 12944-1:1999, Fertilizers and liming materials Vocabulary Part 1: General terms EN 12944-2:1999, Fertilizers and liming materials Vocabulary Part 2: Terms relating to fertilize

18、rs EN 12944-3:2001, Fertilizers and liming materials Vocabulary Part 3: Terms relating to liming materials EN 12948, Liming materials Determination of size distribution by dry and wet sieving EN ISO 3696:1995, Water for analytical laboratory use Specification and test methods (ISO 3696:1987) ISO 331

19、0-1, Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12944-1:1999, EN 12944-2:1999 and EN 12944-3:2001 apply. 4 Principle The sample is added to water. The mixture

20、is stirred and then screened through a series of test sieves. NOTE The method is based upon a method described in the German Methods manual II (1985) 1. BS EN 15704:2008EN 15704:2008 (E) 5 5 Apparatus 5.1 Drying oven, capable of maintaining a temperature of 105 C 5 C; 5.2 Magnetic stirrer, with adju

21、stable rotation, 600 rpm; 5.3 Magnetic stirring rod, 64 mm long ( 5 mm), with a central ring and a diameter of 8 mm ( 1 mm); 5.4 Test sieves, In accordance with ISO 3310-1 with apertures of 100 m and 315 m; NOTE Additional sieve sizes can be added to meet national regulations or the requirements of

22、the consumers. 5.5 Glass beaker, Capacity 2 000 ml and with a diameter of approximately 130 mm and a height of 200 mm. 6 Reagents 6.1 Water, conforming to EN ISO 3696:1995, grade 3. 7 Procedure 7.1 Sampling and sample preparation Sampling is not part of the method specified in this document. A recom

23、mended sampling method is given in EN 1482-1 2. Sample preparation shall be carried out in accordance with EN 1482-2. 7.2 Determination of the moisture content Determine the moisture content of the sample in accordance with EN 12048 and record the result as mass before drying (m1) and mass after dry

24、ing (m2). 7.3 Breakdown of the granules in water Weigh about 100 g of the as received test sample (m3) to the nearest 0,1 g. Measure 1 000 ml of water (6.1) into the glass beaker (5.5). Add the magnetic stirrer rod (5.3) and start the magnetic stirrer (5.2). Adjust the magnetic stirrer to 600 rpm. A

25、dd the test portion into the outside area of the stirred water, and not into the middle vortex in the beaker. Stir for 10 min, maintaining the stirrer at 600 rpm. It is important that the magnetic stirrer avoids any milling action on the test portion. Assemble the sieves (5.4) with the largest apert

26、ure size on the top. Completely wash the contents of the beaker onto the top sieve. Wash the residues on each of the sieves in accordance with the wet sieving method described in EN 12948. Dry (5.1) the residue on each sieve separately at 105 C to a constant mass, and weigh to an accuracy of 0,1 g (

27、m4) after cooling down. BS EN 15704:2008EN 15704:2008 (E) 6 8 Calculation The mass fraction passing through the respective sieve(s), wS in percent, is calculated according to the following Equation: 3241S 100100 mm mmw (1) where m1 is the mass in grams of the sample before drying, m2 is the mass in

28、grams of the dried sample, m3 is the mass in grams of the test portion, m4 is the mass in grams of the dried residue remaining on the sieve(s). The mass of the dried residues (m4) on the sieves shall be used to express the test results in accordance with the requirements of National Fertilizer Regul

29、ations for liming materials. 9 Precision 9.1 Inter-laboratory test An inter-laboratory test has been carried out in 2006 with 12 participating laboratories. Repeatability and reproducibility were calculated according to ISO 5725-1:1994 3. The values derived from this inter-laboratory test may not be

30、 applicable to materials and sample matrices other than those given in Table 1. 9.2 Repeatability The absolute difference between two independent single test results, obtained with the same method on identical test material in the same laboratory by the same operator using the same equipment within

31、a short interval of time, will not be more than 5 % of the cases exceed the values of r given in Table 1. 9.3 Reproducibility The absolute difference between two single test results, obtained with the same method on identical test material in different laboratories by different operators using diffe

32、rent equipment, will not be more than 5 % of the cases exceed the values of R given in Table 1. BS EN 15704:2008EN 15704:2008 (E) 7 Table 1 Mean values, repeatability and reproducibility limits Material and fineness before granulation Particle size x % passing r R r % relative R % relative Dolomite

33、100 m 98,118 1,1551 1,5313 1,1773 1,5607 315 m 99,550 0,3341 2,3743 0,3357 2,3850 Chalk fine 100 m 86,943 1,4084 2,3110 1,6199 2,6581 315 m 90,454 7,2218 6,4734 7,9840 7,1566 Chalk coarse 100 m 50,219 5,6911 20,7561 11,3325 41,3310 315 m 54,112 7,7781 24,6821 14,3742 45,6131 10 Test report The test

34、report shall contain at least the following information: a) all data necessary for the complete identification of the sample; b) date of the sampling and the sampling procedure (if known); c) reference to this European Standard; d) test results and the units in which the results have been expressed;

35、 e) confirmation of the sieve sizes used in the test; f) date of the completion of the test; g) all operating details not specified in this document, or regarded as optional, together with details of any incidents occurred when performing the method which might have influenced the test result(s). BS

36、 EN 15704:2008EN 15704:2008 (E) 8 Bibliography 1 Methodenbuch Band II (1995): Die Untersuchung von Dngemitteln, 4. Auflage, Verband Deutscher Landwirtschaftlicher Untersuchungs- und Forschungsanstalten (VDLUFA), Kapitel 6.6, Seiten 1-2: Bestimmung des Zerfalls von granulierten kohlensauren Kalken un

37、ter Feuchtigkeitseinfluss (Methods Manual II (1995): Analysis of Fertilizers, Association of German Agricultural Experimental and Research Stations, Chapter 6.6, Pages 1-2: Determination of the disaggregation of granulated calcium carbonates (CaCO3, granulated) under the influence of moisture) 2 EN

38、1482-1, Fertilizers and liming materials Sampling and sample preparation Part 1: Sampling 3 ISO 5725-1:1994, Accuracy (trueness and precision) of measurement methods and results Part 1: General principles and definitions BS EN 15704:2008This page has been intentionally left blank BS EN15704:2008BSI

39、GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is inc

40、orporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone f

41、inding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service calle

42、d PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directl

43、y using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of i

44、nformation on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44

45、(0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Inf

46、ormation regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the internation

47、al standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not

48、preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: