EN 3567-004-2001 en Aerospace Series - In-Line Couplers for Use in Multiplex Data Bus Systems in Accordance with MIL-STD-1553B - Part 004 Double In-Line Couplers - Product Standard.pdf

《EN 3567-004-2001 en Aerospace Series - In-Line Couplers for Use in Multiplex Data Bus Systems in Accordance with MIL-STD-1553B - Part 004 Double In-Line Couplers - Product Standard.pdf》由会员分享，可在线阅读，更多相关《EN 3567-004-2001 en Aerospace Series - In-Line Couplers for Use in Multiplex Data Bus Systems in Accordance with MIL-STD-1553B - Part 004 Double In-Line Couplers - Product Standard.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES In-line couplers for use in multiplex data bus systems in accordance with MIL-STD-1553B Part 004: Double in-line couplers - Pro duct standard The European Standard EN 3567-004:2001 has the status ofa British Standard ICs 49.060 BS EN 3567-004: 2001 NO COPYING WITHOU

2、T BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 3567-004:2001 Amd. No. National foreword Date Comments This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and St

3、rategy Committee on 14 December 2001 This British Standard is the official English language version of The UKparticipation in its preparation was entrusted to Technical Committee ACE/6/3, Aerospace - Connectors, which has the responsibility to: EN 3567-004:200 1. - - aid enquirers to understand the

4、text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be

5、obtained on request to its secretary. Cr oss-r e fer enc e s The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using th

6、e “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from

7、 legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 14 December 2001 ISBN O 580

8、38039 4 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3567-004 November 2001 ICs 49.060 English version Aerospace series - In-line couplers for use in multiplex data bus systems in accordance with MIL-STD-1553B - Part 004: Double in-line couplers - Product standard Srie arospatiale - Coupleur

9、s en ligne utiliss dans les systmes multiplexs de bus de donnes suivant MIL-STD- 15538 - Partie 004: Coupleurs en ligne doubles - Norme de prod ui t Luft- und Raumfahrt - Leitungskoppler fr die Anwendung in Multiplex-Datenbussystemen nach MIL-STD-1553B - Teil 004: Doppel-Leitungskoppler - Produktnor

10、m This European Standard was approved by CEN on 4 June 2001. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refere

11、nces concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into

12、its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain

13、, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national

14、 Members. Ref. No. EN 3567-004:2001 E EN 3567-004:2001 (E) Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA) . After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approva

15、l of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2002, and conflicti

16、ng national standards shall be withdrawn at the latest by May 2002. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Gr

17、eece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 2 EN 3567-004:2001 (E) 1 Scope This standard specifies the required characteristics and performance requirements for double in-line couplers for use in multiplex data bus syst

18、ems in accordance with MIL-STD-1553B. It shall be used together with EN 3567-001. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publicatio

19、ns are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2591-100 EN 25

20、91-205 EN 3375-003 EN 3375-004 EN 3375-005 EN 3567-001 MIL-HDBK-217 MIL-STD-1553B Aerospace series - Elements of electrical and optical connection - Test methods - Part 100: General 1) Aerospace series - Elements of electrical and optical connection - Test methods - Part 205: Housing (shell) electri

21、cal continuity Aerospace series - Cables, electrical, for digital data transmissions - Part 003: Single braid - Product standard 2) Aerospace series - Cables, electrical, for digital data transmissions - Part 004: Double braid - Product standard 2) Aerospace series - Cables, electrical, for digital

22、data transmissions - Part 005: Double braid and metallic layer - Product standard 2) Aerospace series - In-line couplers for use in multiplex data bus systems in accordance with MIL-STD-1553B - Part 001: Technical specification Reliability prediction of electronic equipment 3) Digital time division

23、command/Response multiplex data 3) 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 2591-100 apply. 4 Description Double in-line couplers are composed of the following: - two coupling transformers and four isolation resistors; - a screened, environment

24、ally sealed and corrosion resistant enclosure protected with an outer insulation; - cables according to EN 3375-003, EN 3375-004 and EN 3375-005 installed during manufacture. 1) Published as AECMA Prestandard at the date of publication of this standard 2) In preparation at the date of publication of

25、 this standard 3) Published by: Department of Defense (DOD), the Pentagon, Washington D.C. 20301 USA. 3 EN 3567-004:2001 (E) 5 Required characteristics See EN 3567-001. 6 Dimensions, electrical diagram and mass 6.1 Dimensions Dimensions are in millimetres. See figure 1. 85 max. -u 10 max. Key 1 JI -

26、 BUS 2 Marking 3 J2 - BUS 4 J4 - Stub 5 Enclosure with outer insulation 6 J3 - Stub Figure 1 6.2 Electrical diagram See figure 2. Key 1 JI - BUS 2 Screening 4 Blue 3 J2 - BUS 5 White 6 J4 -Stub 7 J3 - Stub Figure 2 4 EN 3567-004:2001 (E) Coupler frequency Direct current 1 MHz 10 MHz 30 MHz 100 MHz 6

27、.3 Mass 15 g including all components (sealing sleeves, etc.) but excluding cable. EN 3567-004 RA EN 3567-004 RB EN 3567-004 RC 4510- 1 5x 1 O -3 IxIO- 4510- xIO- 2,5x10 -3 4510- xIO- 2,5x10 -3 10010 -3 1010 -3 10 Not applicable 7 Performance requirements Operating temperature range: - 65 “C to 150

28、“C or - 65 “C to 200 “C Screening continuity according to EN 2591-205 at ambient temperature: 10 ma max. Insulation resistance: - outer jacket: 100 Ma min.; - between screening and conductors: 100 Ma min Voltage proof test: - outer jacket: 500 V r.m.s.; - between screening and conductors: 500 V r.m.

29、s Surface transfer impedance: see table I. Table 1 I Maximal surface transfer impedance: Z, in ohms per metre I I NOTE Values not defined for couplers of code S. I Salt mist: 500 h Immersion at low air pressure: 1 ,I kPa (30 O00 m) Fluid resistance: EN 3567-001, table 1 Shock: method A, severity 300

30、 Vibrations: - random, level J (1 to 41,7); - gunfire. Tensile strength: 1 O0 N Mean Time Between Failure (MTBF): according to MIL-HDBK-217 5 EN 3567-004:2001 (E) Type of cable EN 3375-003 8 Quality assurance See EN 3567-001. Code A 9 Designation EXAMPLE: 150 200 Description block Identity block COU

31、PLER Number of this standard Temperature class code (see table 2) Code for the types of cable (see table 3) R S Length of cable in decimetres (for ordering and packaging only) EN 3375-005 NOTE If necessary the code I9005 shall be placed between the description block and the identity block. Table 3 T

32、able 2 C I Temper:tye class Code I EN 3375-004 1 B I 10 Marking See EN 3567-001. If the product is too small for the marking to be easily read, a sleeve with appropriate marking shall be used on the cable. 11 Delivery conditions See EN 3567-001. 12 Packaging See EN 3567-001. 13 Storage See EN 3567-0

33、01. 6 BS EN 3567-004:2001 BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si ons British Standards are

34、 updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Br

35、itish Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatical

36、ly receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders&-. Standards are also available from the BSI website at http:

37、/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and internationa

38、l standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscr

39、ibing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipbsi-. Information

40、 regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, ofthe publications

41、 of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise -without prior written permissi

42、on from BSI. This does not preclude the free use, in the course of implementing the standard, ofnecessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission ofBSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyright&-.