EN 2591-409-1999 en Elements of Electrical and Optical Connection - Test Methods - Part 409 Contact Retention in Insert《航空航天系列 光电连接元件的试验方法 第409部分 插入式接触固定》.pdf
《EN 2591-409-1999 en Elements of Electrical and Optical Connection - Test Methods - Part 409 Contact Retention in Insert《航空航天系列 光电连接元件的试验方法 第409部分 插入式接触固定》.pdf》由会员分享,可在线阅读,更多相关《EN 2591-409-1999 en Elements of Electrical and Optical Connection - Test Methods - Part 409 Contact Retention in Insert《航空航天系列 光电连接元件的试验方法 第409部分 插入式接触固定》.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD AEROSPACE SERIES Elements of electrical and optical connection - Test methods - Part 409: Contact retention in insert The European Standard EN 2591-409:1999 has the status of a British standard ICs 49.060 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGH LAW BS EN 25
2、91-4091999 _- STD=BSI BS EN 2511-405-ENGL 1779 E lh24bb7 078Lb57 705 = been prepared under the direction of the Engineering Amd. No. Date Sector Committee, was published under the authority of the Standards Commi - present to the responsible inmnationaUEhropean committee any enquiries on the intepre
3、tation, or proposals for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK. A list of organizatons represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards wh
4、ich implement internalional or European publications refed to in this document may be found in the BSI Standards Catalogue under the section entitled “Intemational Standards Correspondence Index”, or by using the Find” faciiity of the BSI Standards Electronic Catalogue. A British standard does not p
5、urport to include all the necessary provisions of a conira - load to be applied and its applcation point; - allowable displacements 1) under load. 2) after removal of load, . - final measurements and requirements (if applicable). Page 4 EN 2591 -49:1999 1 to5 6 to 60 61 to 130 2 131 4 Method 1 O0 50
6、 (with a minimum of 6 specimens) 25 (with a minimum of 31 specimens) 10 (with a minimum of 34 specimens) 4.1 See table 1. Number of contacts to be tested for each size Table 1 Number to be tested 740 Number of contacts At least one contact shall be close to the insert periphery and one near the cent
7、re. 4.2 Procedure Each contact shall be submitted to the specified axial preload. The load shall be increased at a rate not exceeding 5 N/s until the specified value is reached and maintained for 10 s. The maximum contact displacement shall be measured: - while the load is applied; - after the load
8、is removed. This test shall then be repeated in the opposite direction. 4.3 The measured values shall be within the specified limits. The specimens shall be submitted to a visual examination (EN 2591-101). No damage which would impair their operation shall be observed. Final measurements and require
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- EN25914091999ENELEMENTSOFELECTRICALANDOPTICALCONNECTIONTESTMETHODSPART409CONTACTRETENTIONININSERT 航空航天
链接地址:http://www.mydoc123.com/p-710162.html