DOD A-A-51059-1985 GRADUATE LIQUID LABORATORY (CORROSION RESISTING)《抗腐蚀实验室液体刻度瓶》.pdf

《DOD A-A-51059-1985 GRADUATE LIQUID LABORATORY (CORROSION RESISTING)《抗腐蚀实验室液体刻度瓶》.pdf》由会员分享，可在线阅读，更多相关《DOD A-A-51059-1985 GRADUATE LIQUID LABORATORY (CORROSION RESISTING)《抗腐蚀实验室液体刻度瓶》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 F= A-A-51059 bb 7799774 0010508 3 W /=- y3-92 A-A-51059 9 Uctober 1985 COMMERCIAL ITEM DESCRI PTION b .I -1 GRADUATE, LIQUID, LABORATORY, (Corrosion Resisting) The General Services Administration has authorized the. use of this commercial item description in preference to Mi 1 i tary Spec i fi cat

2、i on MIL-G -36614. This commercial item description covers one type of corrosion resisting laboratory graduate container. Salient characteristics: The Type I graduate shall be supplied without a handle, and the Type II shall be supplied with a handle. and the Size 2 graduate shall have a capacity of

3、 1000 ml. The Size 1 shall have a capacity of 500 milliliters (mi), Table I, Item Identification Specification Designation Type- Size GRADUATE, LIQUID, LABORATORY, Corrosion-Resisting Metal, 500ml. GRADUATE, LIQUID, LABORATORY, Corrosion-Resisting Metal, 1000ml , I 1 II 2 The graduates shall have a

4、minimum thickness of .O14 inches (28 Gauge) and ,013 (29 Gauge) for Type I and II respectively, fabricated from corrosion resisting steel. imperfect ions . The bottoms of the type I and II graduates shall be circular and perpendicular to the vertical axis. Graduate bottans that are concave shall be

5、acceptable. The sides of the graduates shall taper upward from the bottoms (i.e. away from the vertical axis towards the top edge). The upper edges of the graduates shall be flared outward and shall have a pour-out spout. handle shall be attached to the body at the end opposite the spout. The handle

6、 shall be attached by spot welding or resistance welainy. Welds shall be as strong as the parent material. The graduates shall be uniform in consttuction and free from surface For the type II graduate, a The nominal dimensions for the overall height and base diameter of the size 1 graduate shall be

7、4-9/16 and 2-7/8 inches respectively. The width of the top edge along the symmetrical axis shall be 3-5/8 inches. The nominal dimensions for the overall height and base diameter of the size 2 graduate shall be 5-1/2 and 3-13/16 inches respectively. be 4-13/16 inches. The width of the top edge along

8、the symmetrical axis shall All dimensions shall be 2 1/16 inch. FSC 6640 / -. THIS DOCUMENT CONTAINS y PAGES. e DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-COMMERCI

9、AL ITEM DESCRIPTION A-A-51059 Inspection. .Inspection, as used herein, is defined as both examination (such as visual or auditory investigation without the use of special laboratory appliances or procedures) and testing (determination by technical means of physical and chemical properties) of the it

10、em. The insides of the type I and type II graduates shall be graduated in a double scale with markings that are permanent and legible. One scale shall be in ounces (oz) or fluid ounces (fl oz), and the other scale shall be in milliliters (ml) or cubic centimeters (cc). Grams (gm) may be added to the

11、 metric scale. For the size 1 graduate, the oz (fl oz) scale shall be graduated from 2 to 16 ounces in increments of 2 ounces. The metric scale shall be graduated from 50 to 500 ml in increments of 50 ml, For the size 2 graduate, the oz scale shall be graduated from 4 to 32 oz in increments of 4 oz.

12、 The metric scale shall be graduated from 100 to 1000 ml (cc) in increments of 100 ml (cc) . Sampling fc“ inspection. Sampl ing for inspection shall be conducted in accordance I with MIL-STD-105. Where feasible, the same sample shall be used for the determination of two or more inspection characteri

13、stics. inspection purposes shall be conducted at nspection level S-II, AQL 2.5, and sampling for tests (when applicable) shall be conducted at inspection level S-II, APL 1.0. The unit of product for The graduation markings for the size 1 and size 2 graduates shall be accurate to within - + 5 percent

14、 for greater than 100 ml. Workmanship. The container shall be free from defects &ich detract from its appearance or impair its serviceability. - Unit. Each (EA). One graduate, of the size specified, constitutes one unit. Quality Assurance Provisions. purchase order, the contractor is responsible for

15、 the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. T

16、he Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to dssure suppl ies and services conform to prescribed requirements. shall be maintained by the contractor and made available to the Government upon the Gover

17、nments request, at any time, or from time to time, during the performance of the contract and for a period of three years after delivery of the supplies to which such records relate. Responsibility for inspection. Unless otherwise specified in the contract or Kecords. Records of examinations and tes

18、ts performed by or for the contractor 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-51059 bb m 9777974 OOLO510 I U P COMMERCIAL ITEM DESCRIPTION A-A-51059 Tests. Tests shall be conducted to determine compl iance with specification requirement

19、s. two or more test characteristics. 7 Where feasible, the sama sample shall be used for the determination of Contractor certification. The contractor shall certify that the product offered meets the salient characteristics of this description and conforms to the producers own drawings, specificatio

20、ns, standards, and quality assurance practices, The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Regulatory requirements. Federal Food, Drug and Cosmetic Act. If the pr

21、oduct covered by this document has been determined by the U. S. Food and Drug Administration to be under its jurisdiction, the offeror/contractor shall comply, and be responsible for compliance by its subcontractorssuppliers, with the requirements of the Federal Food, Drug and Cosmetic Act, as amend

22、ed, and regulations promulgated thereunder. offeror/contractor shall canply, and be responsible for canpl iance by its subcontractors/suppliers, with the requirements of all other applicable Federal, State, and local statutes, ordinances, and regulations. Recovered materials. The offeror/contractor

23、is encouraged to use recovered material in accordance with Pub1 ic Law 94-580 to the maximum extent practical In addition, the Preservation, packaging, packing, labeling, and marking. preservation, packaging, and packing shall be to a degree of protection to preclude damaae to containers and/or cont

24、ents thereof under normal shiDDinq conditions, Unless otherwise specified, handiing, etc., involving shipment from the supply source to the receiving activity, plus reshipment from receiving activity, and shall conform to applicable carriers rules and regulations. marking shall be as specified in th

25、e contract and/or order. The following National Stock Numbers are covered by this document: Intermediate and exterior package quantities and labeling and 6640-00-427-5025 GRADUATE, LIQUID, LABORATORY Type I, Size 1 6640-00-431-4520 GRADUATE, LIQUID, LABORATORY Type II, Size 2 Ordering data (Intermed

26、iate/exterior package quantities and labeling and marking must be specified Sn the contract and/or order). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-51057 66 7777774 00105LL 3 i- _ - COMMERCIAL ITEM DESCRIPTION A-A-51059 MIL I TARY INTERE

27、STS : PREPARING ACTIVITY: Cus tod i ans : DoD -MB Army-MD Navy-MS Aie Force-O3 Agent : OLA-DM CIVIL AGENCY COORDINATING ACTIVITY: VA-OSS Project No. 6640-1325 Location S3-7-8 *U.S. GOVERNMENT PRINTING OFFICE: lB86 - 605036/46Q66 . 1 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-