DLA SMD-5962-87645 REV E-2013 MICROCIRCUIT LINEAR REGULATING PULSE WIDTH MODULATOR MONOLITHIC SILICON.pdf

《DLA SMD-5962-87645 REV E-2013 MICROCIRCUIT LINEAR REGULATING PULSE WIDTH MODULATOR MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-87645 REV E-2013 MICROCIRCUIT LINEAR REGULATING PULSE WIDTH MODULATOR MONOLITHIC SILICON.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change vendor name of CAGE U4637. Make changes to 1.2.2, 3.3, 4.2, 4.3.1, 4.3.2. Editorial changes throughout. Make changes to table I. 89-06-15 M. A. FRYE B Sheet 6: Table I, Oscillator section, Sawtooth valley voltage, device type 02, under the

2、 min limit column, delete “0.6 V” and substitute “0.5 V”. Changes in accordance with N.O.R. 5962-R145-95. 95-06-29 M. A. FRYE C Drawing updated to reflect current requirements. - ro 02-08-27 R. MONNIN D Five year review requirement. - ro 07-08-16 R. HEBER E Update boilerplate paragraphs to current M

3、IL-PRF-38535 requirements. - ro 13-02-11 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:

4、/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAY MONNIN APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, REGULATING PULSE WIDTH MODULATOR, MONOLITHIC SILICON DRAWING APPROVAL DATE

5、 87-11-24 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-87645 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E238-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87645 DLA LAND AND MARITIME COLUMBUS, OHI

6、O 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown i

7、n the following example: 5962-87645 01 E A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 1524B Regulating pulse width modulator

8、02 1524A Regulating pulse width modulator 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-

9、38535, appendix A. 1.3 Absolute maximum ratings. Input voltage (+VIN) +42 V dc Collector voltage . +60 V dc Logic input range: Device type 01 -0.3 V dc to +5.5 V dc Device type 02 -0.3 V dc to +5.3 V dc Current limit sense inputs . -0.3 V dc to +VINOutput current (each transistor): Device type 01 20

10、0 mA Device type 02 250 mA Reference load current . 50 mA Oscillator charging current . 5 mA Maximum power dissipation (PD) . 1,000 mW 1/ Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) +150C Thermal resistance, junction-to-case (JC) . 60C/W Thermal resistance, junction-to

11、-ambient (JA) 100C/W _ 1/ Must withstand the added PDdue to short circuit test; e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87645 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL

12、E SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Input voltage range (+VIN): Device type 01 +7 V dc to +40 V dc Device type 02 +8.5 V dc to +40 V dc Collector voltage 0 V dc to +60 V dc Error amp common mode range: Device type 01 +2.3 V dc to VREFDevice type 02 +1.5 V dc to +5.5

13、 V dc Current limit sense common mode range 0 V dc to VIN-2.5 V dc Output current range (each transistor): Device type 01 0 mA to 100 mA Device type 02 0 mA to 200 mA Reference load current range . 0 mA to 20 mA Oscillator charging current range . 25 A to 1.8 mA Oscillator frequency range: Device ty

14、pe 01 100 Hz to 400 Hz Device type 02 140 Hz to 480 kHz Oscillator timing resistor range (RT) . 2 k to 150 k Oscillator timing capacitor range (CT): Device type 01 1 nF to 0.1 F Device type 02 470 pF to 0.1 F Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Govern

15、ment specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATI

16、ON MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Mi

17、crocircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the ev

18、ent of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or

19、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87645 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF

20、-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be proces

21、sed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect for

22、m, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, constructio

23、n, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics.

24、 Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrica

25、l tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number i

26、s not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” sha

27、ll be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103

28、(see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certif

29、icate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime-VA shall be required for any change that affects this drawing. 3.9 Verification and re

30、view. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo re

31、production or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87645 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ -55C TA +125C u

32、nless otherwise specified Group A subgroups Device type Limits Unit Min Max Power consumption Standby current ICCVIN= 40 V, VSHUTDOWN= 2.0 V 1,2,3 01 3 12 mA VIN= 8.5 V to 40 V, VSHUTDOWN= 2.0 V 02 3 10 VIN= 6 V 4 Reference section Reference voltage out VREF1 All 4.95 5.05 V 2,3 4.90 5.10 Line regul

33、ation VRLINEVIN= 7 V to 40 V 1,2,3 01 20 mV VIN= 8.5 V to 40 V 02 20 Load regulation VLOADIL= 0 mA to 20 mA 1,2,3 01 30 mV 02 25 Short-circuit current IOSVREF= 0 V 1,2,3 01 25 120 mA 02 150 Temperature stability VREF/ T IL= 0 mA 3/ 1,2,3 01 50 mV Ripple rejection VIN/ VREFf = 120 Hz 4 01 45 dB 02 50

34、 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87645 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical perform

35、ance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Oscillator section Initial accuracy FOSCOSCILLATOR OUTPUT pin is open 4 01 42 48 kHz 02 41 45 Temperature stability Ftemp OSCILLATOR OUTPUT pin is o

36、pen 5,6 01 41.2 48.8 kHz 02 40 46 Voltage stability Vstb VIN= 7 V to 40 V 4,5,6 01 1 % VIN= 8.5 V to 40 V 02 1 Clock pulse amplitude VOSC4,5,6 All 3 V Clock pulse width tPW4,5,6 01 0.2 1.2 s 02 0.25 1.0 Maximum oscillator frequency Fmax RT= 2 k, CT= 470 pF, OSCILLATOR OUTPUT pin load at 2 k and 10 p

37、F 4,5,6 01 400 kHz RT= 2 k, CT= 470 pF 02 480 Minimum oscillator frequency Fmin RT= 150 k, CT= 0.1 F 1,2,3 02 140 Hz Sawtooth peak voltage Vsp VIN= 40 V 4,5,6 01 3.3 3.9 V 02 3.3 3.9 Sawtooth valley voltage Vsv VIN= 40 V 4,5,6 01 0.6 1.2 V 02 0.5 1.0 See footnotes at end of table. Provided by IHSNot

38、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87645 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Condit

39、ions 1/ 2/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Current limit comparator Sense voltage VSENSEVCM= 0 V 1,2,3 01 180 220 mV 1 02 188 212 2,3 180 220 Input bias current ISENSE1,2,3 All 10 A Pulse width modulator comparator Minimum duty cycle outputs

40、 A, B ton/ tOSCVcomp = 0.5 V 4,5,6 All 0 % Maximum duty cycle outputs A, B ton/ tOSCVcomp = 3.9 V 4,5,6 All 45 % Error amplifier section Input offset voltage VIORS 2 k 1,2,3 All 5 mV Input bias current IIB1,2,3 All 5 A Input offset current IIO1,2,3 All 1 A DC open loop gain Avol RL 10 M 1,2,3 01 60

41、dB RL 10 M, VOUT= 1 V to 4 V 02 68 Output low level VLOIsink = 100 A, INV. INPUT NONINV. INPUT 150 mV 1,2,3 01 0.5 V Isink = 70 A, INV. INPUT NONINV. INPUT 150 mV 02 0.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-S

42、TANDARD MICROCIRCUIT DRAWING SIZE A 5962-87645 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA +125C unless otherwise specified Group A subgroups Device type

43、 Limits Unit Min Max Error amplifier section Output high level VHIIsource = 100 A, INV. INPUT NONINV. INPUT 150 mV 1,2,3 01 3.8 V Isource = 70 A, INV. INPUT NONINV. INPUT 150 mV 02 5.0 Common mode rejection CMRR VCM= 2.3 V to VREF1,2,3 01 70 dB VCM= 1.5 V to 5.5 V 02 70 Supply voltage rejection PSRR

44、 VIN= 7 V to 40 V 1,2,3 01 76 dB VIN= 8.5 V to 40 V 02 70 Shutdown input High input voltage VIH1,2,3 01 2 V 02 1.2 High input current IIHVSHUTDOWN= +5.0 V 1,2,3 01 1 mA VSHUTDOWN= +2.5 V 02 3 Low input voltage VIL1,2,3 01 0.6 V 02 0.4 Under voltage lockout Threshold voltage VTVIN= VREF1,2,3 01 4.3 4

45、.7 V Measured at VINat VCCpin with VINrising and RREFopen 02 6.5 8.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87645 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISI

46、ON LEVEL E SHEET 9 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ 2/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output section Collector leakage current ICEXVCE= 60 V 1,2,3 All 50 A Collector

47、saturation voltage VCE(sat) IC= 10 mA 1,2,3 01 0.4 V IC= 100 mA 2.0 IC= 20 mA 02 0.4 IC= 200 mA 2.2 Emitter output voltage VEOIE= 10 mA 1,2,3 All 17.5 V IE= 100 mA 17 Emitter voltage rise time trRE= 2 k 4,5,6 All 400 ns Collector voltage fall time tfRC= 2 k 4,5,6 All 200 ns 1/ For device 01: VIN= 20

48、 V, FOSC= 45 kHz, RT= 2700 1 percent, CT= 0.01 F 1 percent and over operation temperature, unless otherwise specified. 2/ For device 02: VIN= 20 V, FOSC= 43 kHz, RT= 2700 0.1 percent, CT= 0.01 F 0.1 percent and over operation temperature, unless otherwise specified. 3/ Guaranteed, if not tested to the limits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT