DLA SMD-5962-11206 REV A-2011 MICROCIRCUIT HYBRID 5 VOLT POINT OF LOAD (POL) VOLTAGE REGULATOR.pdf

《DLA SMD-5962-11206 REV A-2011 MICROCIRCUIT HYBRID 5 VOLT POINT OF LOAD (POL) VOLTAGE REGULATOR.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-11206 REV A-2011 MICROCIRCUIT HYBRID 5 VOLT POINT OF LOAD (POL) VOLTAGE REGULATOR.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Make corrections to the following tests in Table I: For “Load Regulation” change max values from “-15” and “17” to “+15” and “+17”. For “output response to step load changes” change max values from “150” and “200” to “+150” and “+200”. For “outpu

2、t response to step line changes” change max value from “100” to “+100”. gc 11-09-15 Charles F. Saffle REV SHET REV SHET REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Greg Cecil DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil COLUMBUS, OHIO 4

3、3218-3990 http:/www.landandmaritime.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL APPROVED BY Charles F. Saffle MICROCIRCUIT, HYBRID, 5 VOLT, POINT OF LOAD (POL) VOLTAGE REGULATOR DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 11-08-22 AMSC N/A REVISION LEVEL SIZE A C

4、AGE CODE 67268 5962-11206 A SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E494-11Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11206 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC

5、FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation

6、 hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 11206 01 K X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.

7、2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circui

8、t function as follows: Device type Generic number Circuit function 01 SBB501S Voltage Regulator, 14 W, 1 V Output 02 SBB501R2S Voltage Regulator, 16.8 W, 1.2 V Output 03 SBB501R5S Voltag Regulator, 21 W, 1.5 V Output 04 SBB501R8S Voltage Regulator, 25.2 W, 1.8 V Output 05 SBB502R5S Voltag Regulator,

9、 30 W, 2.5 V Output 06 SBB503R3S Voltage Regulator, 30 W, 3.3 V Output 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qu

10、alification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level

11、is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flo

12、w, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the de

13、vice acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may ha

14、ve a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11206 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outlines. The ca

15、se outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 12 Straight leads with side mounting through holes 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ In

16、put voltage range -0.5 V dc to +7.0 V dc (continuous) Lead temperature (soldering, 10 seconds) +300C Storage temperature range -55C to +125C 1.4 Recommended operating conditions. Input voltage range +4.5 V dc to +5.5 V dc Output Power . 30 W Case operating temperature range (TC). -55C to +85C 2. APP

17、LICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPAR

18、TMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - L

19、ist of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order o

20、f precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the abs

21、olute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11206 D

22、LA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include

23、the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-

24、PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall b

25、e as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified her

26、ein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are

27、 defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements

28、 of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tes

29、ted, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be requ

30、ired from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate

31、of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Managem

32、ent (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11206 DLA LAND AND MARITIME COLUMBUS, OHIO 43218

33、-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC+85C VIN= 5 V dc 5%, CL= 0 unless otherwise specifiedGroup A subgroups Device type Limits Unit Min Max Output Voltage VOUTIOUT= 100% Load 1 01 0.985 1.015 V 2, 3 0.9

34、70 1.030 1 02 1.182 1.218 2,3 1.164 1.236 1 03 1.478 1.523 2, 3 1.462 1.537 1 04 1.773 1.827 2, 3 1.755 1.855 1 05 2.463 2.538 2,3 2.450 2.550 1 06 3.251 3.350 2,3 3.234 3.366 Output Current 1/ IOUTVIN= 4.5, 5.0, 5.5 V dc Each output 1,2,3 01, 02, 03, 04 0 14 A 05 0 12 06 0 9.1 Output Ripple Voltage

35、 2/ VRIP VIN= 4.5, 5.0, 5.5 V dc IOUT= 100% Load, BW = 20 Hz to 2 MHz 1, 2, 3 01, 02, 03, 04 30 mV p-p 05 25 06 20 Line Regulation VRLINE VIN= 4.5, 5.0, 5.5 V dc IOUT= 0%, 50%, 100% load 1, 2, 3 All -0.25 +0.25 % See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networki

36、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11206 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TC+85C VIN= 5 V dc 5%, CL

37、= 0 unless otherwise specifiedGroup A subgroups Device type Limits Unit Min Max Load Regulation VRLOAD VIN= 4.5, 5.0, 5.5 V dc IOUT= 0%, 50%, 100% load 1, 2, 3 01, 02, 03, 04 -15 +15 mV 05, 06 -17 +17 Input Current IINIOUT= 0 A, Pin 10 open 1, 2, 3 All 200 mA Pin 10 shorted to Pin 2 50 Switching Fre

38、quency Fs100% Load, Pin 9 open 1, 2, 3 All 360 440 kHz Input Current Ripple IRIPVIN= 4.5, 5.0,5.5 V dc IOUT= 100% Load, BW = 20 HZ to 2 MHz 1, 2, 3 All 255 mA Efficiency EFFIOUT= 100% Load 1, 2, 3 01, 02 70 % 03 73 04 76 05 82 06 86 Synchronization Frequency EFFExternal clock for Pin 9 1, 2, 3 All 3

39、60 440 kHz Maximum Capacitive Load 3/ 4/ CLIOUT= 100% Load 1 All 10000 F Isolation ISO Any Pin to Case except Pin 12 100 V dc 1 All 100 M Power Dissipation Load Fault PD Short Circuit, Overload 1, 2, 3 01, 02, 03, 04 11 W 05 9.5 W 06 8.0 Output response to step load changes 6/ VTLD50% to/from 100% L

40、oad 4, 5, 6 01, 02, 03, 04 -150 +150 mV pk 05, 06 -200 +200 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11206 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL

41、A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TC+85C VIN= 5 V dc 5%, CL= 0 unless otherwise specifiedGroup A subgroups Device type Limits Unit Min Max Overload trip point ILIMVout = 90% of nominal 1, 2, 3 01, 02, 03, 04 14.5

42、 21.5 A 05 12.5 17.9 06 9.5 13.7 Recovery time, step load changes 6/ 7/ TTLD50% to/from 100% Load 4, 5, 6 All 200 s Output response to step line changes 3/ 8/ VTLN 4.5 V to/from 5.5 V IOUT= 100% Load 4, 5, 6 All -100 +100 mV pk Recovery time, step line changes 3/ 7/ 8/ TTLN4.5 V to/from 5.5 V IOUT=

43、100% Load 4, 5, 6 All 200 s Turn-On Overshoot 9/ VOS0% Load to 100% Load 4, 5, 6 All 100 mV Turn-On Delay 9/ TDLY 0% Load to 100% Load 4, 5, 6 All 1 10 ms 1/ Parameter verified during line and load regulation tests. 2/ Guaranteed for a D.C. to 20 MHz bandwidth. Tested using a 20 KHz to 10 MHz bandwi

44、dth. 3/ Parameter is tested as part of design characterization or after design change. Thereafter, parameter shall be guaranteed to the limits specified. 4/ Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. A capacitive load in excess of the maximum li

45、mit may cause erratic behavior during turn-on. 5/ Overload power dissipation is defined as the device power dissipation with the load set such that VOUT= 90 percent of nominal. 6/ Load step transition time 1.0 s/A for 3.3 V and 2.5 V models and 0.1 s/A for 1.0 V, 1.2 V, 1.5 V, and 1.8 V models. 7/ R

46、ecovery time is measured from the initiation of the transient to where VOUThas returned to within 1 percent of its steady state value. 8/ Line step transition time 10 s. 9/ Turn-on delay time from either a step application of input power or a logic low to a logic high transition on the Enable pin (p

47、in 10) to the point where VOUT= 90 percent of nominal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11206 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Case

48、 outline X. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-11206 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 Case outline X. - Continued Symbol Millimeters Inches Min Max Min Max A 8.51 .335 D 60.83 61.09 2.395 2.405 D1 48.13