DLA MIL-PRF-15160 2 H-2008 FUSES INSTRUMENT POWER AND TELEPHONE (NONINDICATING) STYLE F02.pdf

《DLA MIL-PRF-15160 2 H-2008 FUSES INSTRUMENT POWER AND TELEPHONE (NONINDICATING) STYLE F02.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-15160 2 H-2008 FUSES INSTRUMENT POWER AND TELEPHONE (NONINDICATING) STYLE F02.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5920 INCH-POUND MIL-PRF-15160/2H 15 October 2008 SUPERSEDING MIL-PRF-15160/2G 7 July 2006 PERFORMANCE SPECIFICATION SHEET FUSES, INSTRUMENT, POWER, AND TELEPHONE (NONINDICATING), STYLE F02 This specification is approved for use by all Departments and Agencies of the Department of Defens

2、e. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-15160. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 1. Style F02, fuse. Inches mm 0.004 0.10 0.010 0.25 0.031 0.79 0.230 5.

3、84 0.250 6.35 1.250 31.75 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/2H 2 REQUIREMENTS: Interface and physical dimensions: See figure 1. Terminals: Ferrule type. Material: Brass, copper, phosphor bronze, or copper alloy. Finish: Ni

4、ckel, or silver plated when specified. Strength: Method 211 of MIL-STD-202, test condition E, 10 inch-ounce torque between ferrules and fuse body. Body: Glass tube. Electrical: Current rating: See table I. Voltage rating: See table I. Characteristic: See table I. Overload interrupt: See table I (at

5、all temperatures between minus 55C and plus 85C). Short circuit interrupt: See table I. Shock: F02A 1/100A through 3/4A MIL-STD-202, method 213, test condition I F02A 1A through 30A MIL-STD-202, method 207, (HI shock) F02B 1/100A through 8/10A MIL-STD-202, method 213, test condition I F02B 1A throug

6、h 30A MIL-STD-202, method 207, (HI shock) Vibration: F02A 1/100A through 30A MIL-STD-202, method 204, test condition A (except 5g peak) F02B 1/100A through 8/10A MIL-STD-202, method 201 F02B 1A through 30A MIL-STD-202, method 204, test condition A (except 5g peak) Type designation: Type designation

7、shall be as specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I Type designations and electrical rating. See footnotes at end of table. MIL-PRF-15160/2H Type designation Overload interrupt time 2/ Style Characteristic Maximu

8、m Current 135% of rating Max. 1 hour AC short circuit interrupt. voltage rating 3/ (amperes) 200% of rating (seconds) 300% of rating (seconds) 32 volts 125 volts 250 volts F02 A 250V 1/100A 0.0003 1.0 0.0001 0.003 10,000A 10,000A 35A F02 A 250V 1/32A 0.0008 1.0 0.0002 0.003 10,000A 10,000A 35A F02 A

9、 250V 1/16A 0.009 2.0 0.001 0.030 10,000A 10,000A 35A F02 A 250V 1/8A 0.010 2.0 0.003 0.15 10,000A 10,000A 35A F02 1/ A 250V 15/100A 0.010 2.0 0.008 0.15 10,000A 10,000A 35A F02 1/ A 250V 175/100A 0.010 2.0 0.008 0.15 10,000A 10,000A 35A F02 1/ A 250V 3/16A 0.010 2.0 0.008 0.15 10,000A 10,000A 35A F

10、02 1/ A 250V 2/10A 0.010 2.0 0.008 0.15 10,000A 10,000A 35A F02 A 250V 1/4A 0.020 2.0 0.008 0.20 10,000A 10,000A 35A F02 1/ A 250V 3/10A 0.030 2.5 0.008 0.20 10,000A 10,000A 35A F02 A 250V 3/8A 0.030 2.5 0.008 0.30 10,000A 10,000A 35A F02 A 250V 1/2A 0.030 3.0 0.015 0.40 10,000A 10,000A 35A F02 1/ A

11、 250V 6/10A 0.030 3.0 0.015 0.40 10,000A 10,000A 35A F02 A 250V 3/4A 0.030 3.0 0.015 0.40 10,000A 10,000A 35A F02 A 250V 1A 0.050 3.0 0.015 0.40 10,000A 10,000A 35A F02 1/ A 250V 1 1/4A 0.050 3.0 0.02 0.40 10,000A 10,000A 35A F02 A 250V 1 1/2A 0.050 3.0 0.02 0.40 10,000A 10,000A 35A F02 1/ A 250V 1

12、6/10A 0.050 3.0 0.02 0.40 10,000A 10,000A 35A F02 A 250V 2A 0.080 3.0 0.04 0.40 10,000A 10,000A 35A F02 1/ A 250V 2 1/2A 0.15 3.0 0.04 0.70 10,000A 10,000A 35A F02 A 250V 3A 0.15 5.0 0.04 1.0 10,000A 10,000A 35A F02 A 250V 4A 0.15 5.0 0.04 1.0 10,000A 10,000A 35A F02 A 250V 5A 0.15 5.0 0.04 1.0 10,0

13、00A 10,000A 100A F02 A 250V 6A 0.15 5.0 0.04 1.0 10,000A 10,000A 100A F02 1/ A 125V 8A 0.20 10.0 0.10 2.0 10,000A 10,000A Not rated F02 A 125V 10A 0.20 10.0 0.10 2.0 10,000A 10,000A Not rated F02 A 32V 15A 0.30 10.0 0.10 2.0 10,000A Not rated Not rated 3 Provided by IHSNot for ResaleNo reproduction

14、or networking permitted without license from IHS-,-,-TABLE I Type designations and electrical rating - Continued. See footnotes at end of table. Type designation Overload interrupt time 2/ Style Characteristic Maximum Current 135% of rating Max. 1 hour AC short circuit interrupt. voltage rating 3/ (

15、amperes) 200% of rating (seconds) 300% of rating (seconds) 32 volts 125 volts 250 volts F02 A 32V 20A 0.40 10.0 0.15 2.0 10,000A Not rated Not rated F02 1/ A 32V 25A 0.50 10.0 0.15 2.0 10,000A Not rated Not rated F02 1/ A 32V 30A 0.50 10.0 0.15 2.0 10,000A Not rated Not rated F02 B 250V 1/100A 4.0 1

16、20.0 3.0 40.0 10,000A 10,000A 35A F02 B 250V 1/32A 4.0 120.0 3.0 40.0 10,000A 10,000A 35A F02 B 250V 1/16A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 1/ B 250V 1/10A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 B 250V 1/8A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 1/ B 250V 15/100A 4.0 60.0 1.5 20.0 10,

17、000A 10,000A 35A F02 1/ B 250V 3/16A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 1/ B 250V 2/10A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 B 250V 1/4A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 1/ B 250V 3/10A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 B 250V 3/8A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F

18、02 1/ B 250V 4/10A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 B 250V 1 2A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 1/ B 250V 6/10A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 1/ B 250V 7/10A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 B 250V 3/4A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 1/ B 250V 8/10A

19、 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 B 250V 1A 4.0 60.0 1.5 20.0 10,000A 10,000A 35A F02 1/ B 250V 1 1/4A 4.0 90.0 1.5 30.0 10,000A 10,000A 35A F02 B 250V 1 1/2A 4.0 90.0 1.5 30.0 10,000A 10,000A 35A F02 1/ B 250V 1 6/10A 4.0 90.0 1.5 30.0 10,000A 10,000A 35A F02 B 250V 2A 4.0 90.0 1.5 30.0 10

20、,000A 10,000A 35A F02 B 250V 2 1/2A 4.0 90.0 1.5 30.0 10,000A 10,000A 35A F02 B 250V 2 8/10A 4.0 90.0 1.5 30.0 10,000A 10,000A 35A 4 MIL-PRF-15160/2H Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I Type designations and electrical rating Cont

21、inued. 1/ INACTIVE FOR NEW DESIGN AFTER 30 JANUARY 1970. 2/ The overload interrupt time ranges, as shown, cover the temperature range from minus 55C to plus 85C. For characteristic B, the overload interrupt time at room ambient temperature shall be not less than 12 seconds at 200 percent rating. 3/

22、For silver plated terminals the designator “S” is added after the current rating. MIL-PRF-15160/2H Type designation Overload interrupt time 2/ Style Characteristic Maximum Current 135% of rating Max. 1 hour AC short circuit interrupt. voltage rating 3/ (amperes) 200% of rating (seconds) 300% of rati

23、ng (seconds) 32 volts 125 volts 250 volts F02 B 250V 3A 4.0 90.0 1.5 30.0 10,000A 10,000A 35A F02 B 250V 3 2/10A 4.0 90.0 1.5 30.0 10,000A 10,000A 35A F02 1/ B 125V 4A 4.0 90.0 1.5 30.0 10,000A 10,000A Not rated F02 B 125V 5A 4.0 90.0 1.5 30.0 10,000A 10,000A Not rated F02 1/ B 125V 6 1/4A 4.0 90.0

24、1.5 30.0 10,000A 10,000A Not rated F02 1/ B 125V 7A 4.0 90.0 1.5 30.0 10,000A 10,000A Not rated F02 B 32V 8A 4.0 700.0 1.0 30.0 10,000A Not rated Not rated F02 B 32V 10A 4.0 700.0 1.0 30.0 10,000A Not rated Not rated F02 1/ B 32V 12A 4.0 700.0 1.0 30.0 10,000A Not rated Not rated F02 B 32V 15A 4.0 7

25、00.0 1.0 30.0 10,000A Not rated Not rated F02 B 32V 20A 4.0 700.0 1.0 30.0 10,000A Not rated Not rated F02 1/ B 32V 25A 4.0 700.0 1.0 30.0 10,000A Not rated Not rated F02 1/ B 32V 30A 4.0 700.0 1.0 30.0 10,000A Not rated Not rated 5 Provided by IHSNot for ResaleNo reproduction or networking permitte

26、d without license from IHS-,-,-MIL-PRF-15160/2H 6 VERIFICATION: Qualification inspection is not applicable for the 1/100A thru 3/8A characteristic A fuses, the 1/100A thru 1/8A and 20A thru 30A characteristic B fuses of this specification sheet (see table l) and shall be replaced by acceptance testi

27、ng consisting of Group A and Group B inspections per MIL-PRF-15160, prior to delivery. INSPECTION ROUTINE: Overload tests (group II): Fuses for the overload interrupt test shall be selected and tested as specified in table II for qualification test. TABLE II. Overload tests. Examination of test Numb

28、er of sample fuses Group II Terminal strength Overload interrupt 1/ 135% at room ambient 200% at 55C 200% at +85C 300% at 55C 300% at +85C 20 12 4 4 4 4 4 1/ For characteristic B fuses, only, four additional fuses shall be tested at 200 percent of rating at room ambient temperature. Low voltage over

29、load interrupt (group V for qualification; group III for group C inspection): Four sample characteristic B fuses of each current rating shown in table III shall be subjected to 135 percent current at the voltage specified in the table. The fuses shall interrupt the circuit within 1 hour. The test sh

30、all be conducted at room ambient. TABLE III. Low voltage overload interrupt. (Characteristic B fuses only). Ampere rating Test voltage 1/100A 36V 1/4A 15V 1/2A 10V 7/10A 8V 8/10A 6V 1A 5V Note for low voltage applications, see 6.1.5.1 for caution regarding low voltage applications. Short circuit tes

31、t: The number of group III samples for qualification and qualification retention (group C) testing shall consist of 4 sample fuses of each of the types and of the current ratings as shown in table IV. Short circuit interrupt tests shall be conducted at the ac voltage indicated, and the fuses shall w

32、ithstand a minimum short circuit current as shown in table IV. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/2H 7 TABLE IV. Short circuit tests. Fuse type Current rating Short circuit current AC test voltage F02A 4A 35A 250V F02A 6A 1

33、00A 250V F02A 10A 10,000A 125V F02A 30A 10,000A 32V F02B 3 2/10A 35A 250V F02B 7A 10,000A 125V F02B 30A 10,000A 32V Cross-reference: For applicable cross-reference see table V. The existing stocks of superseded items may be used. When exhausted, the superseding parts shall be used. Provided by IHSNo

34、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE V. Cross reference. 1/ See notes at end of table. Superseding number Superseded numbers for CAGE 81349 81349 96906 71400 71400 75915 75915 75915 98997 F02A250V1/100A 1/ F02GR010A 1/ F02CR010 1/ MS90078-1 2/ AGC1/1

35、00 311.010 312.010 392.010 3AG1/100 F02A250V1/32A F02GR031A F02CR031 MS90078-2 AGC1/32 311.031 312.031 392.031 3AG1/32 F02A250V1/16A F02GR062A F02CR062 MS90078-3 AGC1/16 MGB1/16 311.062 312.062 392.062 3AG1/16 F02A250V1/8A F02GR125A F02CR125 MS90078-4 AGC1/8 MGB1/8 311.125 312.125 392.125 3AG1/8 F02

36、A250V15/100A AGC15/100 311.150 312.150 392.150 3AG15/100 F02A250V175/1000A AGC175/1000 311.175 312.175 392.175 3AG175/100 F02A250V3/16A AGC3/16 311.187 312.187 392.187 3AG3/16 F02A250V2/10 AGC2/10 311.200 312.200 392.200 3AG2/10 F02A250V1/4A F02G2R250A F02CR250 MS90078-5 AGC1/4 311.250 312.250 392.2

37、50 3AG1/4 F02A250V3/10A AGC3/10 311.300 312.300 392.300 3AG3/100 F02A250V3/8A F02GR375A F02CR375 MS90078-6 AGC3/8 311.375 312.375 392.375 3AG3/8 F02A250V1/2A F02GR500A F02CA500 MS90078-7 AGC1/2 311.500 312.500 392.500 3AG1/2 F02A250V6/10A AGC6/10 311.600 312.600 392.600 3AG6/10 F02A250V3/4A F02GR750

38、A F02CR750 MS90078-8 AGC3/4 311.750 312.750 392.750 3AG3/4 F02A250V1A F02G1R00A F02C1R00 MS90078-9 AGC1 311001 312001 392001 3AG1 F02A250V1 1/4A AGC1 1/4 3111.25 3121.25 3921.25 3AG1 1/4 F02A250V1 1/2A F02G1R50A F02C1R50 MS90078-10 AGC1 1/2 3111.50 3121.50 3921.50 3AG1 1/2 F02A250V1 6/10A AGC1 6/10

39、3111.60 3121.60 3921.60 3AG1 6/10 F02A250V2A F02G2R00A F02C2R00 MS90078-11 AGC2 311002 312002 392002 3AG2 F02A250V2 1/2A AGC2 1/2 31102.5 31202.5 39202.5 3AG2 1/2 F02A250V3A F02G3R00A F02C3R00 MS90078-12 AGC3 311003 312003 392003 3AG3 F02A250V4A F02G4R00A F02C4R00 MS90078-13 AGC4 MTH4 311004 312004

40、392004 3AG4 F02A250V5A F02G5R00A F02C5R00 MS90078-14 AGC5 MTH5 311005 312005 392005 3AG5 F02A250V6A F02G6R00A F02C6R00 MS90078-15 AGC6 MTH6 311006 312006 392006 3AG6 F02A125V8A F02A32V8A F02D8R00 AGC8 GLH8 F02A250V10A F02A32V10A F02D10R0 AGC10 GLH10 F02A32V15A F02A15R0 AGC15 F02A32V20A F02A20R0 AGC2

41、0 F02A32V25A F02A25R0 AGC25 F02A32V30A F02A30R0 AGC30 8 MIL-PRF-15160/2HProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15160/2H 9 TABLE V. Cross reference Continued. Superseding number Superseded numbers for CAGE 81349 96906 71400 75915 7591

42、5 98997 F02B250V1/100A 1/ F02GR010B 1/ MS90078-16 2/ MDL1/100 393.010 313.010 3AGTL1/100A-250V F02B250V1/32A F02GR031B MS90078-17 MDL1/32 393.031 313.031 3AGTL1/32A-250V F02B250V1/16A F02GR062B MS90078-18 MDL1/16 393.062 313.062 3AGTL1/16A-250V F02B250V1/10 MDL1/10 313.100 3AGTL1/10A-250F02B250V1/8A

43、 F02GR0125B MS90078-19 MDL1/8 393.125 313.125 3AGTL1/8A-250V F02B250V15/100A MDL15/100 313.150 3AGTL15/100A-250V F02B250V3/16A MDL3/16 313.187 3AGTL3/16A-250V F02B250V2/10 MDL2/10 313.200 3AGTL2/10A-250F02B250V1/4A F02GR250B MS90078-20 MDL1/4 393.250 313.250 3AGTL1/4A-250V F02B250V3/10A MDL3/10 313.

44、300 3AGTL3/10A-250V F02B250V3/8A F02GR0375B MS90078-21 MDL3/8 393.375 313.375 3AGTL3/8A-250V F02B250V4/10A MDL4/10 313.400 3AGTL4/10A-250V F02B250V1/2A F02GR500B MS90078-22 MDL1/2 393.500 313.500 3AGTL1/2A-250V F02B250V6/10A MDL6/10 313.600 3AGTL6/10A-250V F02B250V7/10 MDL7/10 313.700 3AGTL7/10A-250

45、F02B250V3/4A F02GR750B MS90078-23 MDL3/4 393.750 313.750 3AGTL3/4A-250V F02B250V8/10A MDL8/10 313.800 3AGTL8/10A-250V F02B250V1A F02G1R00B MS90078-24 MDL1 393.001 313001 3AGTL1A-250V F02B250V1 1/4A MDL1 1/4 3131.25 3AGTL11/4A-250V F02B250V1 1/2A F02D1R50B MS90078-25 MDL1 1/2 31301.5 3AGTL11/2A-250V

46、F02B250V1 6/10A MDL1 6/10 31301.6 3AGTL16/10A-250V F02B250V2A F02D2R00B MS90078-26 MDL2 313002 3AGTL2A-250V F02B250V2 1/2A MDL2 1/2 31302.5 3AGTL21/2A-250V F02B250V2 8/10A 8/10 31302.8 3AGTL28/10A-250V F02B250V3A F02D3R00B MS90078-27 MDL3 313003 3AGTL3A-250V F02B250V3 2/10A MDL3 2/10 31303.2 3AGTL3

47、2/10A-250V F02B250V4A MDL4 313004 3AGTL4A-250V F02B250V5A MDL5 313005 3AGTL5A-250V F02B250V6 1/4A MDL6 1/4 3136.25 F02B32V7A MDL7 313007 F02B32V8A F02D8R00B MDL8 313008 3AGTL8A32V F02B32V10A MDL10 313010 3AGTL10A32V F02B32V12A MDL12 313012 3AGTL12A32V F02B32V15A MDL15 313015 F02B32V20A MDL20 313020 3AGTL20A32V F02B32V25A MDL25 313025 F02B32V30A MDL30 313030 1/ A letter “S” following the part number signifies silver plating. 2/ A second dash number (-1) signifies silver plating. Referenced documents. In addition to MIL-PRF-15160, this document references the following: MIL-STD-202 The margi