DLA MIL-F-15733 1 J-2010 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL22 [Use DLA MIL-PRF-15733 72 C (1) DLA MIL-PRF-15733 72 C DLA MIL-PRF-15733 72B DLA MIL-PR.pdf

《DLA MIL-F-15733 1 J-2010 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL22 [Use DLA MIL-PRF-15733 72 C (1) DLA MIL-PRF-15733 72 C DLA MIL-PRF-15733 72B DLA MIL-PR.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-F-15733 1 J-2010 FILTERS RADIO FREQUENCY INTERFERENCE HERMETICALLY SEALED STYLE FL22 [Use DLA MIL-PRF-15733 72 C (1) DLA MIL-PRF-15733 72 C DLA MIL-PRF-15733 72B DLA MIL-PR.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5915 MIL-F-15733/1J 1 October 2010 SUPERSEDING MIL-F-15733/1H 27 February 2003 MILITARY SPECIFICATION SHEET FILTERS, RADIO FREQUENCY INTERFERENCE, HERMETICALLY SEALED, STYLE FL22 * This specification is approved for use by all Departments and Agencies of the Department of Defense. The r

2、equirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. FIGURE 1. Case dimensions and circuit diagram. Inactive for new design after 13 April 1983. Used for replacement purposes only. For new design use MIL-PRF-15733/72. See table II for ne

3、w design data. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-15733/1J 2 Dimensions. Dash No. A B C D E F G Min Max Min Max Min Max Min Max Min Max Min Max 0001 2.032 (51.61) 2.156 (54.76) .688 (17.48) .812 (20.62) .172 (4.37) .312

4、(7.92) .265 (6.73) .286 (7.26) .125 (3.18) .250 (6.35) .245 (6.22) .255 (6.48) .09 x .187 0002 2.313 (58.75) 2.437 (61.90) .938 (23.83) 1.062 (26.97) .141 (3.58) .312 (7.92) .359 (9.12) .380 (9.65) .125 (3.18) .312 (7.92) .435 (11.05) .445 (11.30) .06 x .125 or .09 x .187 0003 2.688 (68.28) 2.812 (7

5、1.42) .938 (23.83) 1.062 (26.97) .125 (3.18) .250 (6.35) .359 (9.12) .380 (9.65) .125 (3.18) .250 (6.35) .435 (11.05) .445 (11.30) .06 x .125 or .09 x .187 0004 2.688 (68.28) 2.812 (71.42) 1.063 (27.00) 1.187 (30.15) .187 (4.75) .312 (7.92) .370 (9.40) .380 (9.65) .187 (4.75) .312 (7.92) .365 (9.27)

6、 .375 (9.52) .09 x .187 0005 2.438 (61.93) 2.562 (65.07) 1.188 (30.18) 1.312 (33.32) .125 (3.18) .250 (6.35) .370 (9.40) .380 (9.65) .125 (3.18) .250 (6.35) .525 (13.34) .535 (13.59) .093 Dia. 0006 2.938 (74.63) 3.062 (77.77) 1.313 (33.35) 1.437 (36.50) .308 (7.82) .410 (10.41) .370 (9.40) .380 (9.6

7、5) .308 (7.82) .410 (10.41) .525 (13.34) .535 (13.59) N/A 0007 3.188 (80.98) 3.312 (84.12) 1.438 (36.53) 1.562 (39.67) .308 (7.82) .410 (10.41) .370 (9.40) .380 (9.65) .308 (7.82) .410 (10.41) .650 (16.51) .660 (16.76) N/A Dash No. H J K L M N Mounting thread Terminal thread Terminal style Min Max M

8、in Max Min Max Min Max Max Min Max 0001 .017 (.43) .027 (.69) .12 (3.0) .13 (3.3) .427 (10.85) .447 (11.35) N/A 3.00 (76.2) N/A .312-24 UNF-2A N/A 1 0002 .017 (.43) .027 (.69) .12 (3.0) .13 (3.3) .615 (15.62) .698 (17.73) N/A 3.63 (92.2) N/A .500-28 UNEF-2A N/A 1 0003 .017 (.43) .027 (.69) .12 (3.0)

9、 .13 (3.3) .615 (15.62) .698 (17.73) N/A 3.78 (96.0) N/A .500-28 UNEF-2A N/A 1 0004 .03 (.8) .04 (1.0) .12 (3.0) .13 (3.3) .615 (15.62) .635 (16.13) N/A 3.82 (97.0) N/A .437-20 UNF-2A N/A 1 0005 .017 (.43) .027 (.69) .151 (3.84) .161 (4.09) .865 (21.97) .885 (22.48) N/A 3.44 (87.4) N/A .625-24 UNEF-

10、2A N/A 1 0006 .017 (.43) .027 (.69) .151 (3.84) .161 (4.09) .865 (21.97) .885 (22.48) .12 (3.0) .13 (3.3) 4.85 (123.2) .37 (9.4) .38 (9.7) .625-24 UNEF-2A .190-32 UNF-2A 2 0007 .017 (.43) .027 (.69) .151 (3.84) .161 (4.09) 1.052 (26.72) 1.072 (27.23) .12 (3.0) .13 (3.3) 5.03 (127.8) .37 (9.4) .38 (9

11、.7) .750-20 UNEF-2A .190-32 UNF-2A 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parenthesis. 3. Metric equivalents are given for general information only. 4. Mounting hardware shall be supplied with the filter. 5. Circuit diagram is for information only. FIGURE 1. Case dimensio

12、ns and circuit diagrams - Continued. Inches mm Inches mm .06 1.5 .125 3.18 .09 2.3 .187 4.75 .093 2.36 Dash No. Max weight lbs. 0001 .12 0002 .24 0003 .26 0004 .33 0005 .39 0006 .58 0007 .78 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-15733

13、/1J 3 REQUIREMENTS: Dimensions and configuration: See figure 1. Case: Metal. * Case and mounting hardware finish: In accordance with MIL-PRF-15733. Pure tin finish is prohibited as specified in MIL-PRF-15733. Terminals: Style 1 - Solderable. Style 2 - Threaded stud. * Recommended terminal torque: Th

14、read Torque (in-lb) .190-32 UNF-2A 16 to 18 * Recommended mounting torque: Thread Torque (in-lb) Thread Torque (in-lb) .312-24 UNF-2A 25 to 30 .625-24 UNEF-2A 100 to 115 .437-20 UNF-2A 60 to 70 .750-20 UNEF-2A 120 to 140 .500-28 UNEF-2A 85 to 95 Weight: See figure I. Operating temperature range: -55

15、C to +85C. Rated voltage: See table I. Rated current: See table I. Insertion loss: In accordance with MIL-PRF-15733 and the following: (at +25C): See table I. (at -55C and +85C): Insertion loss shall be as specified in table I except that a degradation of 2 dB from the value specified in table I sha

16、ll be allowed up to 10 MHz. Seal: In accordance with MIL-PRF-15733. Temperature rise: In accordance with MIL-PRF-15733 and the following: 25C maximum for parts rated up to and including 10 amperes. 35C maximum for parts rated above 10 amperes. Provided by IHSNot for ResaleNo reproduction or networki

17、ng permitted without license from IHS-,-,-MIL-F-15733/1J 4 TABLE I. Electrical characteristics. Dash number Circuit diagram Rated voltage (V dc) Rated current (A) Minimum insertion loss (dB) in accordance with MIL-STD-220 at +25C 1/ .15 MHz .30 MHz .60 MHz 1 MHz 10 MHz 100 MHz 1,000 MHz 0001 100 1 5

18、0 60 60 60 60 60 60 0002 100 5 40 50 60 60 60 60 60 0003 100 5 50 60 60 60 60 60 60 0004 100 10 40 50 60 60 60 60 60 0005 100 10 50 60 60 60 60 60 60 0006 100 20 50 60 60 60 60 60 60 0007 100 30 50 60 60 60 60 60 60 1/ Full load insertion loss measurements shall be performed at frequencies between 1

19、50 kHz to 20 MHz inclusive; all other measurements shall be performed at no-load. Dielectric withstanding voltage: In accordance with MIL-PRF-15733 except the duration of application of voltage shall be 1 to 5 seconds. Insulation resistance: In accordance with MIL-PRF-15733. Insulation resistance me

20、asured between both terminals connected together and the case shall be at least: Dash numbers 0001, 0002, and 0004 - 1,000 megohms. 0003, 0005, 0006, and 0007 - 500 megohms. Voltage drop: .5 volt, maximum. Terminal strength: In accordance with MIL-PRF-15733 and the following: Style 2 - method 211, M

21、IL-STD-202; test condition E. Style 1 - method 211, MIL-STD-202; test conditions A (applied force: 5 pounds) and B (5 bends). Salt atmosphere (corrosion): In accordance with MIL-PRF-15733 and method 101, MIL-STD-202; test condition A. Shock (specified pulse): In accordance with MIL-PRF-15733 and met

22、hod 213, MIL-STD-202; test condition I. Mounting: Filters shall be rigidly mounted by the body. Insertion loss shall be measured and shall meet initial requirements. Vibration, high frequency: In accordance with MIL-PRF-15733 and method 204, MIL-STD-202; test condition D (20g). Life: In accordance w

23、ith MIL-PRF-15733 and method 108, MIL-STD 202; test condition B (250 hr). Part or Identifying Number (PIN): M15733/01- (dash number from figure 1 and table I). The Qualified Products List (QPL) associated with this inactive for new design specification will be maintained until acquisition of the pro

24、ducts is no longer required where upon the specification and QPL will be canceled. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-15733/1J 5 * New design data: See table II. * Table II. New design data. Inactive PIN Recommended PIN for new des

25、ign M15733/01- M15733/72- 0001 0037 0002 0042 0003 0043 0004 0045 0005 0045 0006 0048 0007 0051 NOTES: Referenced documents: In addition to MIL-PRF-15733, this specification sheet references the following documents: MIL-PRF-15733/72 MIL-STD-202 MIL-STD-220 Changes from previous issue. The margins of

26、 this specification sheet are marked with an asterisk to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the req

27、uirements of this document based on the entire content irrespective of the marginal notations. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5915-2010-005) DLA - CC Review activities: Army - AT, AV, MI Navy - AS, OS, SH Air Force - 19, 99 NOTE: The activities l

28、isted above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-