DLA DSCC-DWG-84191 REV H-2002 EXTRACTOR ELECTRICAL CARD METAL《金属电卡导出器》.pdf

《DLA DSCC-DWG-84191 REV H-2002 EXTRACTOR ELECTRICAL CARD METAL《金属电卡导出器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-84191 REV H-2002 EXTRACTOR ELECTRICAL CARD METAL《金属电卡导出器》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add black anodized parts. Added second source. 8 Jul 1986 Christopher Rauch B Added dash numbers 9 through 24. Added chemical finish option. Editorial changes throughout. 25 Feb 1988 Randy Larson C Added dash numbers 25 through 32. Added SED symbol option.

2、Changed several dimensions. Added note 4. Added dimension “L“ to figures 1, 2, 3, and 4. Revised pin types in 3.2. Deleted finish “Y“. Changed table I. Editorial changes throughout. 18 Nov 1988 Randy Larson D Added two materials. Added pin length dimension lines. Editorial changes throughout. 30 Mar

3、 1989 Randy Larson E Changed several dimensions. Editorial changes throughout. 22 May 1990 Randy Larson F Changes made in accordance with NOR 5998-R002-92 22 Jul 1992 Randy Larson G PIN structure altered for bent leg, added anodizing for colors and passivation finish, printed wiring board mounting l

4、ocation, and location of SED symbol figure. Updated drawings, document, and editorial changes throughout. Update CAGE CODE to 037Z3. 25 Sep 1995 John F. Raye H Section 2 updated to remove cancelled documents and add the superseding replacements. Added an additional source of supply. Editorial change

5、s throughout. 30 Aug 2002 Thomas M. Hess PREVIOUS CAGE CODE 14933 SUPERSEDED BY 037Z3. THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. Prepared in accordance with ASMEY14.100 Selected item drawing REV H H PAGE 17 18 REV STATUS REV H H H H H H H H H H H H H H H H H OF PAGES PAGES 1 2 3 4 5

6、 6 7 8 9 10 11 12 13 14 15 16 17 PMIC N/A PREPARED BY Christopher Rauch DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 http:/www.dscc.dla.mil/programs/milspec/docsearch.asp Original date of drawing CHECKED BY Randy Larson 17 Apr 1985 APPROVED BY Ivan Jones TITLE: EXTRACTOR, ELECTRICAL CARD,

7、 METAL SIZE A CODE IDENT. NO. 14933 DWG NO. 84191 REV H PAGE 1 OF 18 AMSC N/A 5998-E039 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS C

8、OLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84191 REV H PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of metal extractors intended to aid in removing circuit card assemblies or printed wiring assemblies from their installed positions. 1.2 Part or Identifying N

9、umber (PIN). The complete PIN shall be as shown in the following example: 84191 Drawing number 01 Dash number (see table I) B Finish (see 3.3 and table II) A Material (see 3.2.1) BL Bent leg option (see 3.1.3 and figure 6) NOTE: Select extractor configuration (dash number), finish, material, and opt

10、ions from the above paragraph as shown in the following examples: Example 1: 84191347A (DSCC drawing 84191 extractor, electrical card, metal with the following selections; angled handle without locking tab (figure 2), 5/16 (.165 mm) thick boards, mounting pin length is .312 (7.93 mm) inches long, ri

11、ght hand, has purple anodized finish, made from .063 (1.60 mm) thick aluminum alloy in accordance with AMS-QQ-A-225/7 or AMS-QQ-A-250/8, and does not have bent leg (figure 2, right hand). Example 2: 8419137ETBL (DSCC drawing 84191 extractor, electrical card, metal with the following selections; stra

12、ight handle with locking tab (figure 4), 5/16 (.165 mm) thick boards, mounting pin length is .312 (7.93 mm) inches long, left hand, has gold chemical film finish with ESD symbol, made from .063 (1.60 mm) thick aluminum alloy in accordance with AMS-QQ-A-225/8 or AMS-QQ-A-250/11, and has bent leg (fig

13、ure 6, left hand). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those

14、 listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-C-5541 - Chemical Conversion Coatings on Aluminum Alloys. MIL-A-8625 - Anodic Coating for Aluminum an

15、d Aluminum Alloys. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-130 - Identification Marking Of U.S. Military Property. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Unless otherwise indicated, copies of federal and military specifications and standards are available from the Document Autom

16、ation and Production Services (DAPS), Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84191

17、 REV H PAGE 3 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise sp

18、ecified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). ASTM INTERNATIONAL (ASTM) ASTM A666 - Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. (Application for copies should be addressed to AS

19、TM International, 100 Barr Harbor Drive, West Coshohocken, PA 19428-2959.) SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) SAE AMS-QQ-P-35 - Passivation Treatments for Corrosion-Resistant Steel. SAE AMS-QQ-A-225/7 - Aluminum Alloy 5052, Bar, Rod, and Wire; Rolled, Drawn or Cold Finished. SAE AMS-QQ-A-225/8 -

20、Aluminum Alloy 6061, Bar, Rod, Wire and Special Shapes; Rolled, Drawn or Cold Finished. SAE AMS-QQ-A-250/8 - Aluminum Alloy 5052, Plate and Sheet. SAE AMS-QQ-A-250/11 - Aluminum Alloy 6061, Plate and Sheet. (Application for copies should be addressed to the SAE World Headquarters, 400 Commonwealth D

21、rive, Warrendale, PA 15096-0001.) (Non-Government standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services. They are also distributed a

22、mong technical groups and using Federal agencies.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

23、 specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. See table I and figures 1 through 7. 3.1.1 Extractor orientation with board. See figure 1. 3.1.2 Standard straight leg configuration. Standard (straight) leg shall be as illustrated in figures 1 through 5.

24、Standard (straight) leg will be blank for the suffix digit in the PIN, see 1.2. 3.1.3 Optional bent leg configuration. Bent leg (option BL) is available for all configurations. The bent leg option shall be as illustrated in figure 6. Bent leg (option BL) shall include the suffix “BL“ in the PIN, see

25、 1.2. 3.1.4 Circuit card mounting location. Circuit card mounting location, see figure 7. 3.2 Materials. 3.2.1 Extractor. The extractor shall be fabricated from one of the materials listed below. The material shall be as specified in the PIN, see 1.2. PIN designator Material A Aluminum alloy 5052-H3

26、2, .063 inch (1.60 mm) thick in accordance with AMS QQ-A-225/7 or AMS-QQ-A-250/8. S Stainless steel, type 301 or type 304 in accordance with ASTM A666. T Aluminum alloy 6061-T6, .063 inch (1.60 mm) thick in accordance with AMS-QQ-A-225/8 or AMS-QQ-A-250/11. 3.2.2 Mounting pin. Mounting pin shall be

27、made of stainless steel (CRES 302). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84191 REV H PAGE 4 VIEW OF RIGHT HAND EXTRACTOR FROM BOTH SIDES OF BOARD VIEW OF RI

28、GHT HAND EXTRACTOR WITH TAB RELEASE NOTE: 1. Retainer must be in the unlocked position before extractor may be used. FIGURE 1. Extractor orientation with board. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS,

29、 OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84191 REV H PAGE 5 Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm .001 .003 .005 0.03 0.08 0.13 .006 .020 .050 0.15 0.51 1.27 .090 .093 .099 2.29 2.36 2.51 .108 .125 .156 2.74 3.18 3.96 .180 .250 .290 4.60 6.35 7.40 .353 .360 1.000 1.500 8.97 9.

30、14 25.40 38.10 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .010 (0.25 mm). 4. Width dimension shall be .290 .020 inch (7.37 mm 0.51 mm) when board width dimension A increases to .142 (3.61 mm) or .165 inch (4

31、.19 mm), see table I. FIGURE 2. Angled handle, without locking tab (dash numbers 01 through 08, 33 and 34). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84191 REV H

32、 PAGE 6 Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm .003 .005 .020 0.08 0.13 0.51 .050 .090 .093 1.27 2.29 2.36 .099 .100 .108 2.51 2.54 2.74 .125 .130 .156 3.18 3.30 3.96 .180 .250 .290 4.60 6.35 7.40 .353 .360 1.000 1.500 8.97 9.14 25.40 38.10 NOTES: 1. Dimensions are in inches. 2.

33、 Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .010 (0.25 mm). 4. Width dimension shall be .290 .020 inch (7.37 mm 0.51 mm) when board width dimension A increases to .142 (3.61 mm) or .165 inch (4.19 mm), see table I. FIGURE 3. Angled handle, with l

34、ocking tab (dash numbers 09 through 16, 35 and 36). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84191 REV H PAGE 7 Inches mm Inches mm Inches mm Inches mm Inches m

35、m Inches mm .003 .005 .020 0.08 0.13 0.51 .050 .090 .093 1.27 2.29 2.36 .099 .100 .108 2.51 2.54 2.74 .125 .130 .156 3.18 3.30 3.96 .250 .290 .353 6.35 7.40 8.97 .360 1.000 1.500 9.14 25.40 38.10 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless othe

36、rwise specified, tolerances are .010 (0.25 mm). 4. Width dimension shall be .290 .020 inch (7.37 mm 0.51 mm) when board width dimension A increases to .142 (3.61 mm) or .165 inch (4.19 mm), see table I. FIGURE 4. Straight handle, with locking tab (dash numbers 17 through 24, 37 and 38). Provided by

37、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84191 REV H PAGE 8 Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm .003 .005 .020 0.08 0.13 0.51 .050 .090 .093 1.27 2.

38、29 2.36 .099 .100 .108 2.51 2.54 2.74 .125 .130 .156 3.18 3.30 3.96 .250 .290 .353 6.35 7.40 8.97 .360 1.000 1.500 9.14 25.40 38.10 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .010 (0.25 mm). 4. Width dimensi

39、on shall be .290 .020 inch (7.37 mm 0.51 mm) when board width dimension A increases to .142 (3.61 mm) or .165 inch (4.19 mm), see table I. FIGURE 5. Straight handle, without locking tab (dash numbers 25 through 32, 39 and 40). Provided by IHSNot for ResaleNo reproduction or networking permitted with

40、out license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84191 REV H PAGE 9 LEFT HAND RIGHT HAND Bent leg (option BL) without tabs, figures 2 and 5. LEFT HAND RIGHT HAND Bent leg (option BL) with tabs, figures 3 and 4. Inches mm Inches mm Inches mm

41、Inches mm .005 0.13 .020 0.51 .035 0.89 .250 6.35 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .010 (0.25 mm). 4. Width dimension shall be .290 .020 inch (7.37 mm 0.51 mm) when board width dimension A increase

42、s to .142 (3.61 mm) or .165 inch (4.19 mm), see table 1. 5. Bent leg (option BL) is available for all configurations, figures 1 through 5. Bent leg option shall include a suffix “BL“ in the PIN, see 1.2, 3.1.3 and table I. FIGURE 6. Bent leg (option BL) configurations. Provided by IHSNot for ResaleN

43、o reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84191 REV H PAGE 10 VIEW OF RIGHT HAND EXTRACTOR WITH BOARD MOUNTING INFORMATION Inches mm Inches mm Inches mm Inches mm .002 .060 0.05 1.52 .094 .12

44、5 2.38 3.18 .250 .290 6.35 7.37 .370 9.40 NOTES: 1. Edge of printed board is to be flush with end of extractor and retainer or indent .12 (3.05 mm) inch from edge of retainer for more extraction and movement. 2. Dimensions are in inches. Metric equivalents are given for information only. 3. Unless o

45、therwise specified, tolerances are .02 (0.5 mm). Figure 7. Circuit card mounting location. TABLE I. Design and dimensions. PIN designation 84191- 1/ Dimension “A” 2/ Dimension “L” Configuration L = left hand R = right hand Figure Angled handle, without locking tabs 01*# 02*# 03*# 04*# 05*# 06*# 07*#

46、 08*# Inches mm .040 (1.02) .040 (1.02) .075 (1.91) .075 (1.91) .105 (2.67) .105 (2.67) .142 (3.61) .142 (3.61) Inches mm .188 (4.78) .188 (4.78) .188 (4.78) .188 (4.78) .250 (6.35) .250 (6.35) .250 (6.35) .250 (6.35) L R L R L R L R 2 2 2 2 2 2 2 2 See footnotes at end of table. Provided by IHSNot

47、for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84191 REV H PAGE 11 TABLE I. Design and dimensions. Continued. PIN designation 84191- 1/ Dimension “A” 2/ Dimension “L” Configuration L =

48、left hand R = right hand Figure Angled handle, with locking tab 09*# 10*# 11*# 12*# 13*# 14*# 15*# 16*# Inches mm .040 (1.02) .040 (1.02) .075 (1.91) .075 (1.91) .105 (2.67) .105 (2.67) .142 (3.61) .142 (3.61) Inches mm .188 (4.78) .188 (4.78) .188 (4.78) .188 (4.78) .250 (6.35) .250 (6.35) .250 (6.35) .250 (6.35) L R L R L R L R 3 3 3 3 3 3 3 3 Straight handle, with locking tab: 17*# 18*# 19*# 20*#