DLA AN104301 THRU AN104400 REV 3-1986 BOLT - DRILLED HEX HEAD 6 HOLES 5625-18.pdf

《DLA AN104301 THRU AN104400 REV 3-1986 BOLT - DRILLED HEX HEAD 6 HOLES 5625-18.pdf》由会员分享，可在线阅读，更多相关《DLA AN104301 THRU AN104400 REV 3-1986 BOLT - DRILLED HEX HEAD 6 HOLES 5625-18.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、 AN304303 THRU AN304400 REV 3 53 m 7977735 0000253 2 - K TO FULL THD *O16 OR CHAMFE DRILL ,188 TO DEPTH SHOWN 6 HOLES SPACE AS SHOWN WITH WITH SHANK WITHIN .O03 FIR. , CHAMFER (OPPOSITE 30 SIDE TO OPTIONAL) .875 DIA SECTION THRU THREAD PROFILE L 1.125 1.188 1.250 1.312 1.375 1.438 1.500 1.562 1.625

2、1.688 1.750 1 .e12 1.875 - +.O00 PPAT NO. -.:60 I . AN104308 AN104311 K L +.o00 - .o6a 1.938 .56; 2.000 .625 2.062 .688 2.188 .812 2,250. .875 2.312 .g38 2.125 .750 2.375 1.000 2.500 .1.125 2.625 1.250 2.750 1.375 2.875 1.500 3.000 1.625 3.125 1.750 PART NO. L AN104319 3.250 AN104320 3.375 AN104321

3、3.500 AN104322 3.625 AN104323 3.750 AN104325 4 .OO AN104326 4.125 AN104327 4.250 AN104328 4.375 AN104329 4.500 AN104330 4.625 AN104331 4.750 AN104332 4.875 AN104324 3.875 K K +.O00 PART NO. L +.O00 - .O60 . -.o60 1.875 AN104333 5.000 3.625 2.000 AN104334 5.125 3.750 2.125 AN104335 5.250 3.875 2.250

4、AN104336 5.375 4.000 2.375 AN104337 5.500 4.125 2.500 AN104338 5.625 4.250 2.625 AN104339 5.750 4.375 2.750 AN104340 5.875 4.500 2.875 AN104341 6;OOO 4.625 3.000 AN104342 3.125 AN104343 3.250 AN104344 3.375 AN104345 3.500 AN104346 PART NO. a) THREAD PO HEAD. MAXIMUM TWO IMPERFECT THREADS. IOTE: (1)

5、SBANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMETER AND HEXAGON SHALL BE WITHIN ,026 FIR. UTERIAL: STEEL AMs6322 IARDNESS: RO

6、CKWELL C26-32 FINISH: CADMIUM PLATE AMs2400 SURFACE ROUGHNESS: AS107 4ANUFACTURING SPECIFICATION: AMs7452 NSPECTION: ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCORDANCE WITH AHS2640 3REAK SHARP EDGES ,003-.O15 UNLESS OTHERWISE SPECIFIED. IHENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERNC

7、ES; LINEAR DIMENSIONS f.010, ANGULAR DIMENSIONS 22. DO HOT USE UNASSIGNED PART NUhBERS. NAGTIVE FOR NEW DESIGN AFTER 3 MARCH 1969 NO SUPERSEDING STANDARD. HIS STANDARD WAS DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE CAE. AN104348 AN1011347 AN 104 3 49 AN104350 AN104351 AN104352 AN104353 AN104354 AN104355 n AIR FORCE-NAVY AERONAUTICAL STANDARD AN104301 P.A. Af-11 THRU o a O I AN104400 CUIT. NAVY-AS BOLT - DRILLED HEX HEAD, 6 HOLES, .5625-18 AANY-AV Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-