DLA A-A-59412 A-2013 SWAGING MACHINE ROTARY FLOOR- MOUNTED.pdf

《DLA A-A-59412 A-2013 SWAGING MACHINE ROTARY FLOOR- MOUNTED.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59412 A-2013 SWAGING MACHINE ROTARY FLOOR- MOUNTED.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: STDZNMGTdla.mil Defense Logistics Agency-Aviation, ATTN: VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can change,

2、 you may want to verify the currency of this address information using assist database at https:/assist.dla.mil. FSC 3446 INCH-POUND A-A-59412A 16 December 2013 SUPERSEDING A-A-59412 26 October 1999 COMMERCIAL ITEM DESCRIPTION SWAGING MACHINE, ROTARY, FLOOR- MOUNTED The General Services Administrati

3、on has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers floor-mounted rotary swaging machines and accessories intended for use in pointing, reducing diameters, and forming shapes on tubing and solid stock and swa

4、ging fittings to cables and hoses. 2. CLASSIFICATION. The rotary swaging machines shall be of the following types and sizes. Swaging machine sizes are shown in tables I, II, and III. The type and size to be furnished shall be as specified (see 7.2(b). Type I - Rotary die swaging machine (See Table I

5、) Type II - Stationary die swaging machine (See Table II) Type III - Rotary die-closing swaging machine (See Table III) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59412A 2 TABLE I. Sizes of type I rotary die swaging machines. Size Diametral

6、capacity, inches Solids Tubing 1 1/16 2 1/8 5/16 3 3/8 4 1/2 1 5 5/8 1-3/4 6 1 2 7 1-3/8 3 8 2 4 9 3 6 TABLE II. Sizes of type II stationary die swaging machines. Size Diametral capacity, inches Solids Tubing 1 13/32 1 2 3/4 2-1/4 3 1-1/2 3-3/8 4 2 4-1/2 5 2-1/2 6 TABLE III. Sizes of type III die-cl

7、osing swaging machines. Size Diametral capacity, inches Solids Tubing Cable 1 3/16 1/2 1/16 2 3/8 3/4 3 1/2 1 5/16 4 1 2 5 1-1/2 3 1 NOTE: Machine size and capacity for each type shall not be less than the stated requirements of the size ordered nor greater than the next larger size as shown in tabl

8、e I, II, or III. 3. SALIENT CHARACTERISTICS 3.1 General requirements. The machine shall be new and one of the manufacturers current models capable of operation in accordance with the requirements herein. All parts subject to wear, breakage, or distortion shall be accessible for adjustment, replaceme

9、nt, and repair. 3.2 Components. The swaging machine shall include, as a minimum, the following components: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59412A 3 3.2.1 Base. The base shall support the other elements of the machine and shall inc

10、orporate materials, shape, and mass to minimize adverse vibration and deflection. The base shall provide a means for leveling and anchoring the machine. 3.2.2 Electric-motor drive. The rotary swaging machine flywheel shall be driven by an electric motor through a belt drive system. Unless otherwise

11、specified (see 7.2(c), motor horsepower, speed, and drive system shall be that considered by the manufacturer as standard. 3.2.3 Flywheel. The flywheel shall be a casting of iron or steel and dynamically balanced. The design and mass of the flywheel shall store and deliver energy required to perform

12、 all operations within machine capacity without imposing overload on the electric motor. On a type I or III machine, the flywheel shall be mounted directly on the spindle. On a type II machine, the roll cage shall be mounted within the flywheel. 3.2.4 Spindle. A hollow steel spindle shall be mounted

13、 in the head on antifriction bearings of a size, type, and precision suitable for the application and designed to withstand repeated axial loads. Unless otherwise specified (see 7.2(d), the spindle hole diameter shall be that considered by the manufacturer as standard and meet or exceed the machine

14、tubing diametral capacity. 3.2.5 Dies. Unless otherwise specified (see 7.2(e), the swaging machine shall be the two-die type. If required, dies shall be provided as specified (see 7.2(f). 3.2.5.1 Cable terminal dies. If required, the type III swaging machine shall include dies to swage the following

15、 standard cable terminals as specified (see 7.2(g): a. Fork end. b. Eye end. c. Single shank ball. d. Double shank ball. 3.2.6 Roll cage. A roll cage or rack assembly containing steel rollers in recesses shall be mounted in an inside or head ring. On a type I and III machine, the roll cage or rack s

16、hall remain free to impart striking force to the rotating hammers. On a type II machine, the roll cage or rack shall revolve with the rotating head to impart striking force to the stationary hammers. 3.2.7 Die-closing device. On a type III machine only, a die-closing device shall be provided. The di

17、e-closing device shall consist of hydraulically operated wedges interposed between the hammers and dies, allowing the dies to remain open while the machine is running. 3.2.8 Manual controls. Unless otherwise specified (see 7.2(h), the following manual switches, as a minimum, shall be provided: a. Po

18、wer on/off switches. b. Hydraulic system power on/off switches (type III machine only). 3.2.9 Coolant system. Unless otherwise specified (see 7.2(i), the rotary swaging machine shall be flood cooled. As a minimum, the coolant system shall consist of a reservoir, pump, strainer, and all necessary pip

19、ing. The system shall be equipped with a method to control the rate of coolant flow from the reservoir and to direct coolant flow to the grinding area. When specified (see 7.2(j), an Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59412A 4 option

20、al coolant filtration system shall be provided. 3.2.10 Hydraulic system. On a type III machine, the hydraulic system shall conform to the requirements of International Organization for Standardization (ISO) ISO-4413. The hydraulic system shall be complete and include all pumps, valves, piping, cylin

21、ders, and controls. Means shall be provided to prevent damage to the components from overpressure. A filter system shall be provided to ensure delivery of clean fluid. 3.2.11 Electrical system. Unless otherwise specified (see 7.2(k), the electrical system shall conform to the American National Stand

22、ards Institute/National Fire Prevention Association (ANSI/NFPA) 79. The machine shall have dual 230/460-volt, 3-phase, 60-hertz circuit capability and shall be wired for the voltage specified (see 7.2(l). 3.2.12 Electric motors. The rotary swaging machine drive motor shall have sealed and permanentl

23、y lubricated ball or roller bearings, shall be energy efficient, and shall conform to the National Electrical Manufacturers Association (NEMA) MG-1. The drive motor(s) shall be totally enclosed and fan cooled (TEFC) or open dripproof (ODP) as specified (see 7.2(m). 3.2.13 Optional accessories. Optio

24、nal accessories shall be provided as specified (see 7.2(n). 3.3 Performance. Unless otherwise (see 7.2(o), the rotary swaging machine shall meet the performance requirements shown in table IV when tested in accordance with section 5.3 through 5.3.5. TABLE IV. Performance requirements. Type Swaging r

25、equirements I Pointing, forming, tapering, and reducing the diameter on tubing, wire, and malleable solids. II Pointing and tapering square and rectangular entry cross sections. Forming fluted shapes, splines, blade ends, and other cross sections from round, square, or rectangular stock. III Assembl

26、ing cable terminals and other fittings to cables. Locking bands to pins or shafts. Forming center reductions between shoulders. Pointing and reducing round stock. 3.4 Machine dimensions and weight. If required, the maximum machine dimensions (length, width, and height) and machine weight shall not e

27、xceed the restrictions specified (see 7.2(p). 3.5 Safety and health requirements. The machine shall be designed and manufactured in accordance with ANSI B11.7. The manufacturer shall ensure that the machine and all equipment and accessories used on the machine shall be in compliance with Occupationa

28、l Safety and Health Administration (OSHA) 29 CFR PART 1910. If a conflict arises between the ANSI and OSHA standards, the OSHA standards shall apply. 3.6 System of units. The U.S. Customary System of Units (US) or the International System of Units (SI) shall be used to graduate measuring and indicat

29、ing devices. When only one system of graduation is acceptable, the particular graduation required shall be as specified (see 7.2(q). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59412A 5 Regardless of the measurement system used, all measuring

30、 and indicating devices on the machine shall be graduated in the same system. When specified (see 7.2(r), measuring and indicating devices shall be graduated in both the US and SI system of measurements. 3.7 Nameplate. A nameplate shall be securely attached to the machine. Unless otherwise specified

31、 (see 7.2(s), the nameplate shall contain the following information: a. Nomenclature. b. Manufacturers name. c. Serial number. d. Machine model designation. e. Power input (volts, total amperes, phase, frequency). f. Short-circuit/over-current rating. g. Contract number or order number. h. National

32、stock number. i. Date of manufacture. 3.8 Lubrication plate or chart. When specified (see 7.2(t), a lubrication plate or chart shall be attached to the machine. The information provided on the plate or chart shall include: a. Points of lubricant application. b. Servicing interval. c. Type of lubrica

33、nt(s) with SAE number or lubricant identifier. 3.9 Hydraulic fluid plate or chart. When specified (see 7.2(u), a hydraulic fluid plate or chart shall be attached to the machine. The information provided on the plate or chart shall include: a. Servicing interval. b. Type of fluid with SAE number or f

34、luid identifier. c. Type of filter. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Environmental protection. Th

35、e item shall meet all applicable Environmental Protection Agency (EPA) restrictions in effect on the date of the contract. These regulations apply to the emission of materials hazardous to the environment or the users health and shall be adhered to during the manufacturing, service, transportation,

36、storage, and operation/use of the item. 5. QUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The products shall meet the salient characteristics of this commercial item description; conform to the manufacturers own drawings, specifications, standards, and quality assurance practices; and be the

37、same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59412A 6 5.2 Inspection. The rotary swaging machine shall be inspected

38、 to determine compliance with all requirements specified in this CID. 5.3 Testing. Unless otherwise specified (see 7.2(v), the rotary swaging machine shall be tested in accordance with sections 5.3.1 through 5.3.5. 5.3.1 Test setup and conditions. Unless otherwise specified (see 7.2(w), the manufact

39、urer shall be responsible for supplying all tooling and material(s) and shall conduct all tests required by the Government. The manufacturer shall provide test instruments and equipment with calibration traceable to National Institute of Standards and Technology (NIST) and shall provide certificatio

40、n of calibration as specified (see 7.2(x). 5.3.2 Operational test. The rotary swaging machine shall be operated in accordance with the manufacturers standard operational test procedures. The rotary swaging machine shall be operated at no load for not less than one hour. Proper operation of all contr

41、ols and features shall be verified during the trial period. 5.3.3 Performance tests. No less than five tubes or solids for the type and size of machine specified, equal to the maximum capacity of the machine, shall be swaged to the shape of the dies requested by the government. The type III machine

42、shall be operated to assemble no less than five fittings to cables. Complete swaging of the assemblies shall be accomplished without distortion of the fittings. All performance tests shall be completed without making any adjustments to or performing any maintenance on the machine. 5.3.4 Noise level

43、tests. Noise level measurements shall be made in accordance with section 8.4.2 of ANSI S1.13 to ensure conformance with noise limits set by OSHA 29 CFR PART 1910.95, Occupational Noise Exposure. 5.3.5 Optional tests. Optional tests shall be conducted as specified (see 7.2(y). 5.4 Acceptance. Unless

44、otherwise specified (see 7.2(z), preliminary and final acceptance tests shall be conducted at the manufacturers site. The results of the performance tests shall be compared with the requirements shown in table IV. Failure of the machine to meet the requirements shown in table IV shall be cause for r

45、ejection. 6. PACKAGING. Unless otherwise specified (see 7.2(aa), preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES 7.1 Sources of referenced documents. 7.1.1 Government documents. Copies of Federal documents may be obtained from the Superintendent of Documen

46、ts, U.S. Government Printing Office, Washington, DC 20402. Electronic copies of may be obtained from https:/assist.dla.mil/. Occupational Safety and Health Administration (OSHA) OSHA 29 CFR Part 1910 Occupational Safety and Health Standards for General Industry Provided by IHSNot for ResaleNo reprod

47、uction or networking permitted without license from IHS-,-,-A-A-59412A 7 Applications for copies should be sent to the U.S. Department of Labor, 200 Constitution Avenue NW, Room 423, Washington, DC 20210. Electronic copies of OSHA standards may be obtained from https:/www.osha.gov/. Federal Acquisit

48、ion Regulation (FAR) FAR Paragraph 23.403 Use of Recovered Materials and Biobased Products The FAR may be obtained from the US Government Printing Office 732 North Capitol Street N.W., Washington, DC 20401. Electronic copies of OSHA standards may be obtained from http:/www.acquisition.gov/far/. 7.1.

49、2 Industry standards. Copies of industry standards referenced in this CID may be obtained from the following addresses: American National Standards Institute (ANSI) ANSI B11.7 Machine Tools - Cold Headers and Cold Formers, Safety Requirements for Construction, Care, and Use ANSI S1.13 Measurement of Sound Pressure Levels in Air Applications for copies shou