DIN EN 1603-2013 Thermal insulating products for building applications - Determination of dimensional stability under constant normal laboratory conditions (23 C 50 % relative humi.pdf

《DIN EN 1603-2013 Thermal insulating products for building applications - Determination of dimensional stability under constant normal laboratory conditions (23 C 50 % relative humi.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1603-2013 Thermal insulating products for building applications - Determination of dimensional stability under constant normal laboratory conditions (23 C 50 % relative humi.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、May 2013 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.

2、100.60!%$*X“2010753www.din.deDDIN EN 1603Thermal insulating products for building applications Determination of dimensional stability under constant normal laboratoryconditions (23 C/ 50 % relative humidity);English version EN 1603:2013,English translation of DIN EN 1603:2013-05Wrmedmmstoffe fr das

3、Bauwesen Bestimmung der Dimensionsstabilitt im Normalklima (23 C/ 50 % relative Luftfeuchte);Englische Fassung EN 1603:2013,Englische bersetzung von DIN EN 1603:2013-05Produits isolants thermiques destins aux applications du btiment Dtermination de la stabilit dimensionnelle dans des conditions de l

4、aboratoire constanteset normales (23 C/ 50 % dhumidit relative);Version anglaise EN 1603:2013,Traduction anglaise de DIN EN 1603:2013-05SupersedesDIN EN 1603:2007-06www.beuth.deDocument comprises 13 pagesIn case of doubt, the German-language original shall be considered authoritative.04.13DIN EN 160

5、3:2013-05 2 A comma is used as the decimal marker. National foreword This document (EN 1603:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products” (Secretariat: DIN, Germany) The responsible German body involved in its preparation was the Normenausschuss

6、 Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-56-60 AA Wrmedmmstoffe. The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 5725-2 DIN ISO 5725-2 Amendments This standard differs from DIN EN 1603:2007-0

7、6 as follows: a) the standard has been editorially revised. Previous editions DIN 53431: 1977-08 DIN EN 1603: 1997-01, 2007-06 National Annex NA (informative) Bibliography DIN ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination

8、of repeatability and reproducibility of a standard measurement method EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1603 March 2013 ICS 91.100.60 Supersedes EN 1603:1996English Version Thermal insulating products for building applications - Determination of dimensional stability under constan

9、t normal laboratory conditions (23 C/ 50 % relative humidity) Produits isolants thermiques destins aux applications du btiment - Dtermination de la stabilit dimensionnelle dans des conditions de laboratoire constantes et normales (23C/50% dhumidit relative) Wrmedmmstoffe fr das Bauwesen - Bestimmung

10、 der Dimensionsstabilitt im Normalklima (23C/50% relative Luftfeuchte) This European Standard was approved by CEN on 15 December 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national s

11、tandard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version i

12、n any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech

13、Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EURO

14、PEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1603:2013: EEN 1603:2013 (E)

15、 2 Contents Page Foreword . 3 1 Scope 5 2 Normative references . 5 3 Terms and definitions 5 4 Principle 6 5 Apparatus . 6 6 Test specimens 6 6.1 Dimensions of test specimens 6 6.2 Number of test specimens . 6 6.3 Preparation of test specimens . 8 6.4 Conditioning of test specimens. 8 7 Procedure .

16、8 7.1 Test conditions . 8 7.2 Test procedure . 8 8 Calculation and expression of results 9 9 Accuracy of measurement . 10 10 Test report 10 DIN EN 1603:2013-05 EN 1603:2013 (E) 3 Foreword This document (EN 1603:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials an

17、d products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by Septemb

18、er 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1603:1996. The revision of this standard contains

19、 no major changes, only minor corrections and clarifications of an editorial nature. This European Standard is one of a series of standards which specify test methods for determining dimensions and properties of thermal insulating materials and products. lt supports a series of product standards for

20、 thermal insulating materials and products which derive from the Council Directive of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products (Directive 89/106/EEC) through the consideration of the essential requ

21、irements. This European Standard has been drafted for applications in building, but it may also be used in other areas where it is relevant. This European test standard is one of the following group of interrelated standards on test methods for determining dimensions and properties of thermal insula

22、tion materials and products, all of which fall within the scope of CEN/TC 88: EN 822, Thermal insulating products for building applications Determination of length and width EN 823, Thermal insulating products for building applications Determination of thickness EN 824, Thermal insulating products f

23、or building applications Determination of squareness EN 825, Thermal insulating products for building applications Determination of flatness EN 826, Thermal insulating products for building applications Determination of compression behaviour EN 1602, Thermal insulating products for building applicat

24、ions Determination of the apparent density EN 1603, Thermal insulating products for building applications Determination of dimensional stability under constant normal laboratory conditions (23 C/50 % relative humidity) EN 1604, Thermal insulating products for building applications Determination of d

25、imensional stability under specified temperature and humidity conditions EN 1605, Thermal insulating products for building applications Determination of deformation under specified compressive load and temperature conditions EN 1606, Thermal insulating products for building applications Determinatio

26、n of compressive creep DIN EN 1603:2013-05 EN 1603:2013 (E) 4 EN 1607, Thermal insulating products for building applications Determination of tensile strength perpendicular to faces EN 1608, Thermal insulating products for building applications Determination of tensile strength parallel to faces EN

27、1609, Thermal insulating products for building applications Determination of short-term water absorption by partial immersion EN 12085, Thermal insulating products for building applications Determination of linear dimensions of test specimens EN 12086, Thermal insulating products for building applic

28、ations Determination of water vapour transmission properties EN 12087, Thermal insulating products for building applications Determination of long-term water absorption by immersion EN 12088, Thermal insulating products for building applications Determination of long-term water absorption by diffusi

29、on EN 12089, Thermal insulating products for building applications Determination of bending behaviour EN 12090, Thermal insulating products for building applications Determination of shear behaviour EN 12091, Thermal insulating products for building applications Determination of freeze-thaw resistan

30、ce EN 12429, Thermal insulating products for building applications Conditioning to moisture equilibrium under specified temperature and humidity conditions EN 12430, Thermal insulating products for building applications Determination of behaviour under point load EN 12431, Thermal insulating product

31、s for building applications Determination of thickness for floating floor insulating products EN 13793, Thermal insulating products for building applications Determination of behaviour under cyclic loading EN 13820, Thermal insulating materials for building applications Determination of organic cont

32、ent According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,

33、 Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 1603:2013-05 EN 1603:2013 (E) 5 1 Scope This European Standard specifies the

34、 equipment and procedures to evaluate irreversible dimensional changes of test specimens and full size products with time under constant normal laboratory conditions. It is applicable to thermal insulating products. 2 Normative references The following documents, in whole or in part, are normatively

35、 referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 822, Thermal insulating products for building applications Determ

36、ination of length and width EN 825, Thermal insulating products for building applications Determination of flatness ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measureme

37、nt method 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 length l long linear dimension of the major surface of the test specimen parallel to the longer linear dimension of the original product 3.2 width b short linear dimension of the major

38、 surface of the test specimen, measured at right angles to the length 3.3 deviation from flatness S maximum distance between the product placed on a flat surface with the convex side uppermost and the flat surface 3.4 normal laboratory conditions (23 2) C and (50 5) % relative humidity DIN EN 1603:2

39、013-05 EN 1603:2013 (E) 6 4 Principle Measure length, width and deviation from flatness of the test specimens at several time intervals under normal laboratory conditions until relative stability has been achieved. Dimensional stability is determined using one or more of the following methods: Metho

40、d A: determination of linear dimensions of full size products; Method B: determination of linear dimensions of products using test specimens with dimensions smaller than those of full size products; Method C: determination of deviation from flatness of full size products. 5 Apparatus Method A: Measu

41、ring equipment as defined in EN 822. Method B: A frame fixed on a flat reference surface with a dial gauge of 0,01 mm accuracy or any device (optical, electrical etc.) which has an accuracy of 0,1 mm/m (see examples in Figure 1 and Figure 2); and either Method B1: Metal plates of at least 20 mm in d

42、iameter (see Figure 1). The actual diameter is to be chosen so that the pressure exerted by the dial gauge is less than 2 kPa; or Method B2: Metal wire (see Figure 2). Method C: Measuring equipment as defined in EN 825. Any test equipment which provides the same result to at least the same accuracy

43、may be used. 6 Test specimens 6.1 Dimensions of test specimens The thickness of the test specimens shall be equal to the original product thickness. Method A: The test specimen shall be the full size product. Method B1: 500 mm 500 mm or, if less than 500 mm 500 mm, as large as possible. In every cas

44、e, it shall be greater than 250 mm 250 mm. Method B2: 250 mm 250 mm. Method C: The test specimen shall be the full size product. 6.2 Number of test specimens When testing full size products, the number of test specimens shall be as specified in the relevant product standard. If measurements are made

45、 on test specimens taken from a full size product, at least three test specimens shall be tested. DIN EN 1603:2013-05 EN 1603:2013 (E) 7 In the absence of a product standard or any other European Technical Specification, the number of test specimens may be agreed between parties. Dimensions in milli

46、metres Key 1 flat reference surface 2 metal plate 3 dial gauge 4 metal bead Figure 1 Example of suitable equipment for method B1 DIN EN 1603:2013-05 EN 1603:2013 (E) 8 Dimensions in millimetres Key 1 optical or electrical device 2 rule 3 metal wire Figure 2 Example of suitable equipment for method B

47、2 6.3 Preparation of test specimens The test specimens shall be cut by methods that do not change the structure from that of the original product. If test specimens are not the full size products, the length and width directions shall be marked on them. The method of selection of the test specimens

48、shall be as specified in the relevant product standard. In the absence of a product standard or any other European Technical Specification, the method of selection may be agreed between parties. 6.4 Conditioning of test specimens The test specimens shall be conditioned for at least 24 h at (23 2) C

49、and (50 5) % relative humidity. 7 Procedure 7.1 Test conditions Testing shall be carried out at (23 2) C and (50 5) % relative humidity. The test specimens shall be conditioned, either vertically or horizontally, with their major faces exposed to the test atmosphere (e.g. supported by a wire mesh away from the chamber walls). 7.2 Test procedure Measure dimensional stability using either method A, B or C. The c