DIN EN 13523-3-2014 Coil coated metals - Test methods - Part 3 Colour difference - Instrumental comparison German version EN 13523-3 2014《涂覆金属卷材 试验方法 第3部分 色差 仪器比较 EN 13523-3 2014的德.pdf

《DIN EN 13523-3-2014 Coil coated metals - Test methods - Part 3 Colour difference - Instrumental comparison German version EN 13523-3 2014《涂覆金属卷材 试验方法 第3部分 色差 仪器比较 EN 13523-3 2014的德.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13523-3-2014 Coil coated metals - Test methods - Part 3 Colour difference - Instrumental comparison German version EN 13523-3 2014《涂覆金属卷材 试验方法 第3部分 色差 仪器比较 EN 13523-3 2014的德.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、August 2014 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、25.220.60!%:;5“2232418www.din.deDDIN EN 13523-3Coil coated metals Test methods Part 3: Colour difference Instrumental comparison;English version EN 13523-3:2014,English translation of DIN EN 13523-3:2014-08Bandbeschichtete Metalle Prfverfahren Teil 3: Farbabstand Farbmetrischer Vergleich;Englische F

3、assung EN 13523-3:2014,Englische bersetzung von DIN EN 13523-3:2014-08Tles prlaques Mthodes dessai Partie 3: Diffrence de couleur Comparaison au moyen dinstruments;Version anglaise EN 13523-3:2014,Traduction anglaise de DIN EN 13523-3:2014-08SupersedesDIN EN 13523-3:2001-12www.beuth.deDocument compr

4、ises 11 pagesIn case of doubt, the German-language original shall be considered authoritative.07.14DIN EN 13523-3:2014-08 2 A comma is used as the decimal marker. National foreword This document (EN 13523-3:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, (Secretaria

5、t: DIN, Germany), Working Group WG 9 “Testing of coil coated metals” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Beschichtungsstoffe und Beschichtungen (DIN Standards Committee Coatings and Coating Materials), Working Committee NA 002-

6、00-07 AA Allgemeine Prfverfahren fr Beschichtungsstoffe und Beschichtungen. Amendments This standard differs from DIN EN 13523-3:2001-12 as follows: a) terms and definitions have been aligned with EN ISO 4618; b) Clause 1 “Scope” and Clause 8 “Procedure” have been revised. Previous editions DIN EN 1

7、3523-3: 2001-12 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13523-3 June 2014 ICS 25.220.60 Supersedes EN 13523-3:2001English Version Coil coated metals - Test methods - Part 3: Colour difference - Instrumental comparison Tles prlaques - Mthodes dessai - Partie 3: Diffrence de couleur - Com

8、paraison au moyen dinstruments Bandbeschichtete Metalle - Prfverfahren - Teil 3: Farbabstand - Farbmetrischer Vergleich This European Standard was approved by CEN on 7 May 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this E

9、uropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official vers

10、ions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria,

11、 Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, S

12、witzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nat

13、ional Members. Ref. No. EN 13523-3:2014 EEN 13523-3:2014 (E) 2 Contents Page Foreword 3 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Principle 6 5 Apparatus .6 6 Sampling .6 7 Specimens 6 8 Procedure .7 8.1 Calibration 7 8.2 Measurement 7 9 Expression of results 7 10 Accuracy .8 1

14、1 Test report 8 Bibliography 9 DIN EN 13523-3:2014-08 EN 13523-3:2014 (E) 3 Foreword This document (EN 13523-3:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national sta

15、ndard, either by publication of an identical text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn at the latest by December 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rig

16、hts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13523-3:2001. The main technical changes are: a) the definitions were aligned with those in EN ISO 4618; b) the scope and procedure were amended. EN 13523, Coil coated met

17、als Test methods, consists of the following parts: Part 0: General introduction Part 1: Film thickness Part 2: Gloss Part 3: Colour difference Instrumental comparison Part 4: Pencil hardness Part 5: Resistance to rapid deformation (impact test) Part 6: Adhesion after indentation (cupping test) Part

18、7: Resistance to cracking on bending (T-bend test) Part 8: Resistance to salt spray (fog) Part 9: Resistance to water immersion Part 10: Resistance to fluorescent UV radiation and water condensation Part 11: Resistance to solvents (rubbing test) Part 12: Resistance to scratching Part 13: Resistance

19、to accelerated ageing by the use of heat Part 14: Chalking (Helmen method) Part 15: Metamerism Part 16: Resistance to abrasion DIN EN 13523-3:2014-08 EN 13523-3:2014 (E) 4 Part 17: Adhesion of strippable films Part 18: Resistance to staining Part 19: Panel design and method of atmospheric exposure t

20、esting Part 20: Foam adhesion Part 21: Evaluation of outdoor exposed panels Part 22: Colour difference Visual comparison Part 23: Resistance to humid atmospheres containing sulfur dioxide Part 24: Resistance to blocking and pressure marking Part 25: Resistance to humidity Part 26: Resistance to cond

21、ensation of water Part 27: Resistance to humid poultice (Cataplasm test) Part 29: Resistance to environmental soiling (Dirt pick-up and striping) According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European St

22、andard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

23、Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 13523-3:2014-08 EN 13523-3:2014 (E) 5 1 Scope This part of EN 13523 specifies procedures for determining the instrumental colour difference (CIELAB) of an organic coating on a metallic substrate. Establishing a standard as well as the

24、 magnitude of an acceptable colour difference are not covered by this method. Two methods are given in this part of EN 13523: a) instrumental colour difference measurement using a tristimulus colorimeter; b) instrumental colour difference measurement using a spectrophotometer or equivalent. Care sho

25、uld be taken when measuring e.g. textured surfaces; fluorescent coatings; metameric coatings; multi-coloured, pearlescent, metallic or special colour effect coatings. In order to determine whether metamerism is present, the metamerism index is determined (see EN 13523-15) and/or a visual examination

26、 (see EN 13523-22) is performed with different artificial light sources. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated refer

27、ences, the latest edition of the referenced document (including any amendments) applies. EN 13523-0:2014, Coil coated metals Test methods Part 0: General introduction EN 23270, Paints and varnishes and their raw materials Temperatures and humidities for conditioning and testing (ISO 3270) EN ISO 116

28、64-4, Colorimetry Part 4: CIE 1976 L*a*b* Colour space (ISO 11664-4) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13523-0:2014 and the following apply. 3.1 colour sensation resulting from the perception of light of a given spectral composition by t

29、he human eye Note 1 to entry: The use of the German word “Farbe” alone, i.e. not in combinations of words, for coating materials is deprecated. DIN EN 13523-3:2014-08 EN 13523-3:2014 (E) 6 Note 2 to entry: A colour is characterized by hue, chroma, and lightness. SOURCE: FprEN ISO 4618:2014, 2.58 3.2

30、 embossed coating coating which, when dried, has been mechanically impressed with a pattern 3.3 metamerism phenomenon perceived when two specimens have the same colour under the lighting of an illuminant, but different spectral reflection and transmission curves SOURCE: FprEN ISO 4618:2014, 2.157 3.

31、4 textured coating coating which, after drying, is characterized by a regularly structured surface SOURCE: FprEN ISO 4618:2014, 2.255 4 Principle The tristimulus values X, Y and Z (see EN ISO 11664-3) of both standard colour reference panel (called “standard” through the text) and specimen are measu

32、red. Colour differences between the two measurements are calculated from these tristimulus values. 5 Apparatus Ordinary laboratory apparatus, together with the following: 5.1 Tristimulus colorimeter. 5.2 Recording spectrophotometer or equivalent. The instrument shall provide the possibility of obtai

33、ning the tristimulus values either for the 2-standard colorimetric observer and source C or for the 10-supplementary standard colorimetric observer and source D65. The latter conditions of 10 observer and D65 source are preferred. Preferably the measured area shall have a minimum diameter of 10 mm.

34、If a smaller diameter is used, this shall be stated in the test report. 6 Sampling See EN 13523-0. 7 Specimens See EN 13523-0. The surfaces to be measured shall be at least as large as the area of the measuring aperture and shall be flat against the measuring aperture. DIN EN 13523-3:2014-08 EN 1352

35、3-3:2014 (E) 7 8 Procedure 8.1 Calibration Use the apparatus in accordance with the manufacturers instructions, particularly with regard to warm-up time and calibration. 8.2 Measurement Measure the colour at ambient temperature. In cases of dispute, the test temperature shall be defined as (23 2) C

36、and the relative humidity as (50 5) %, in accordance with EN 23270. Conditioning is carried out in accordance with EN 13523-0:2014, Clause 6. Measure in the wavelength range of at least 400 nm to 700 nm in intervals not greater than 20 nm with a half-intensity width of the monochromator less than 20

37、 nm. In special cases, such as highly chromatic paint films with steep spectral reflectance curves measurements in 10 nm or 5 nm intervals using a monochromator with 10 nm or 5 nm half-intensity width are more accurate. The illumination/viewing geometry shall be one of the following: a) 45:0 or 0:45

38、; b) integrating sphere (d:8 or 8:d). The inclusion or exclusion of specular reflection shall be stated in the test report. Determine first the tristimulus values of the standard or recall them from a data file. Thereafter determine the tristimulus values of the specimen to be measured. Using these

39、tristimulus values, calculate the colour difference and its components, using the CIELAB formula given in EN ISO 11664-4. Usually the software associated with the spectrophotometer shall give the absolute Lab values and the colour difference on each colour dimension. If a different colour equation i

40、s used, this shall be stated in the test report. Colour differences shall not be compared when they are obtained by different colour scale system equations. In case of dispute the test shall be carried out on the same equipment. Textured and embossed coatings should be measured with an integrating s

41、phere or with 45-annular/circumferential illumination. An average result can be obtained by turning the specimens three times through 90 to obtain four measurements. 9 Expression of results Express the value of the instrumental colour difference in terms of the relevant colour coordinates L* a* b* o

42、r L* *abC *abH in addition to the total colour difference *abE . L* positive = lighter than standard L* negative = darker than standard a* positive = Redder/less green than standard a* negative = Greener/less red than standard b* positive = Yellower/less blue than standard DIN EN 13523-3:2014-08 EN

43、13523-3:2014 (E) 8 b* negative = Bluer/less yellow than standard *abC positive = specimen has more chroma (colour saturation) relative to the standard *abC negative = specimen has less chroma (colour saturation) relative to the standard *abH positive = In the CIELAB system *abH positive indicates th

44、at the hue angle (arctan b*/a*) deviates from the standard in an anticlock-wise direction, i.e. in the sequence red to yellow to green to blue. *abH negative = The hue angle deviates from the standard in a clockwise direction, i.e. in the sequence blue to green to yellow to red. The total colour dif

45、ference *abE is a mathematical combination of the above colour difference components. Calculate the total colour difference *abE , of textured coatings as the mean of the individual *abE measurements. 10 Accuracy For dark colours (e.g. blues, browns, blacks) or for bright colours of high chroma (e.g

46、. reds, yellows), the error in reflectance measurement at certain wavelengths might be sufficient to give misleading results. In these cases visual comparison is essential (see EN 13523-22). 11 Test report The test report shall contain at least the following information: a) all details necessary to

47、identify the product tested; b) a reference to this part of EN 13523 (EN 13523-3); c) the instrument used; d) the source and observer used; e) the geometry used; f) the colour difference equation; g) inclusion or exclusion of specular reflection; h) the colour difference value (see Clause 9); i) com

48、ponents of the colour difference, if required; j) any deviation from the test method specified; k) any unusual features (anomalies) observed during the test; l) the date of the test. DIN EN 13523-3:2014-08 EN 13523-3:2014 (E) 9 Bibliography 1 EN 1396, Aluminium and aluminium alloys Coil coated sheet

49、 and strip for general applications Specifications 2 EN 10169:2010+A1:2012, Continuously organic coated (coil coated) steel flat products Technical delivery conditions 3 EN 13523-15, Coil coated metals Test methods Part 15: Metamerism 4 EN 13523-22, Coil coated metals Test methods Part 22: Colour difference Visual comparison 5 FprEN ISO 4618:2014, Paints and varnishes Terms and definitions (ISO/FDIS 4