BS ISO 5892-2013 Rubber building gaskets Materials for preformed solid vulcanized structural gaskets Specification《建筑橡胶衬垫 预成型密实的硫化结构衬垫材料 规格》.pdf

《BS ISO 5892-2013 Rubber building gaskets Materials for preformed solid vulcanized structural gaskets Specification《建筑橡胶衬垫 预成型密实的硫化结构衬垫材料 规格》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 5892-2013 Rubber building gaskets Materials for preformed solid vulcanized structural gaskets Specification《建筑橡胶衬垫 预成型密实的硫化结构衬垫材料 规格》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 5892:2013Rubber building gaskets Materials for preformed solidvulcanized structural gaskets SpecificationBS ISO 5892:2013 BRITISH STANDARDNational forewordThis British Sta

2、ndard is the UK implementation of ISO 5892:2013.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/70, Elastomeric seals for joints in pipework andpipelines.A list of organizations represented on this committee can beobtained on request to its secretary.This publication

3、does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 72968 3ICS 83.140.50; 91.100.50Compliance with a British Standard cannot confer immuni

4、ty fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2013.Amendments issued since publicationDate Text affectedBS ISO 5892:2013 ISO 2013Rubber building gaskets Materials for preformed solid vulcanized structural gas

5、kets SpecificationProfils en caoutchouc pour le btiment Matriaux pour profils de structure compacts prforms vulcaniss SpcificationsINTERNATIONAL STANDARDISO5892Second edition2013-06-15Reference numberISO 5892:2013(E)BS ISO 5892:2013ISO 5892:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED D

6、OCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission

7、can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5892:2013ISO 5892:2013(E) ISO

8、 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Types of material . 25 Working temperature range. 26 Material and workmanship . 27 Dimensions and tolerances . 28 General requirements . 28.1 Test pieces . 28.2 Hardness . 38.3 Tensil

9、e strength and elongation at break . 38.4 Compression set . 38.5 Accelerated ageing . 38.6 Ozone resistance 39 Specific requirements . 49.1 General . 49.2 High-density ozone resistance 49.3 Holding force 49.4 Watertightness 49.5 Flammability . 49.6 Contact and migration staining 49.7 Low-temperature

10、 brittleness . 49.8 Low-temperature compression set . 4Annex A (informative) Holding force test 6Bibliography 9BS ISO 5892:2013ISO 5892:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of prep

11、aring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in

12、liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC

13、Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some

14、 of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarat

15、ions received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement. The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 4, Products (other than hoses).This s

16、econd edition cancels and replaces the first edition (ISO 5892:1981), which has been technically revised.iv ISO 2013 All rights reservedBS ISO 5892:2013INTERNATIONAL STANDARD ISO 5892:2013(E)Rubber building gaskets Materials for preformed solid vulcanized structural gaskets Specification1 ScopeThis

17、International Standard specifies material requirements for preformed, solid vulcanized rubber structural gaskets in sealing and supporting applications for buildings.NOTE Specifications for non-supporting gaskets are given in ISO 3934.2 Normative referencesThe following documents, in whole or in par

18、t, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 37, Rubber, vulcanized or thermoplastic Determi

19、nation of tensile stress-strain propertiesISO 188, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance testsISO 812:2011, Rubber, vulcanized or thermoplastic Determination of low-temperature brittlenessISO 815-1, Rubber, vulcanized or thermoplastic Determination of compression

20、 set Part 1: At ambient or elevated temperaturesISO 815-2, Rubber, vulcanized or thermoplastic Determination of compression set Part 2: At low temperaturesISO 1382, Rubber VocabularyISO 1431-1, Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing

21、ISO 3302-1, Rubber Tolerances for products Part 1: Dimensional tolerancesISO 3865, Rubber, vulcanized or thermoplastic Methods of test for staining in contact with organic materialISO 7619-1, Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 1: Durometer method (Shore ha

22、rdness)ISO 15821, Doorsets and windows Water-tightness test under dynamic pressure Cyclonic aspects3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 1382 and the following apply.3.1structural gasketbuilding gasket that directly supports glasses, etc. an

23、d makes components watertight and airtightNote 1 to entry: It consists of gaskets and lock strips. ISO 2013 All rights reserved 1BS ISO 5892:2013ISO 5892:2013(E)3.2gasketcomponent with channels which support both glasses and support framesNote 1 to entry: Gaskets having two channels are called doubl

24、e-channel gaskets and those having one channel are called single-channel gaskets.3.3lock stripcomponent that is inserted into the lock-strip cavities for ensuring the required watertightness and airtightness4 Types of materialTwo types of materials are specified. Type E, with a nominal hardness of 7

25、5 Shore A, is intended for the gaskets and for the lock strip. Type F, with a nominal hardness of 85 Shore A, is intended only for the lock strip.5 Working temperature rangeThe working temperature ranges of gaskets are divided into the following categories:a) P1: temperature of gasket: 20 C to +55 C

26、;b) P2: temperature of gasket: 20 C to +85 C;c) P3: temperature of gasket: 40 C to +70 C;d) P4: temperature of gasket: 40 C to +100 C.6 Material and workmanship6.1 All materials and workmanship shall be in accordance with good commercial practice.6.2 Gaskets shall be made from ozone-resistant rubber

27、 and shall not depend for ozone resistance solely on surface protection which can be removed by abrasion, detergents, or other means.6.3 Gaskets shall be free from porosity, significant surface defects, and dimensional irregularities, particularly on the sealing faces.7 Dimensions and tolerancesDime

28、nsions shall be the subject of agreement between the interested parties. Tolerances shall be in accordance with the specifications of ISO 3302-1.8 General requirements8.1 Test piecesTest pieces shall be cut from the finished product. If they cannot be so prepared, they shall be taken from moulded te

29、st slabs of suitable dimensions made from the same batch of material used for the gaskets and vulcanized under conditions which are comparable with the conditions used in production.2 ISO 2013 All rights reservedBS ISO 5892:2013ISO 5892:2013(E)8.2 HardnessWhen tested in accordance with the method sp

30、ecified in ISO 7619-1, the hardness shall comply with the requirements of Table 1.8.3 Tensile strength and elongation at breakWhen tested in accordance with the method specified in ISO 37 using a dumbbell test piece, the tensile strength and elongation at break shall comply with the requirements of

31、Table 1.8.4 Compression setWhen tested in accordance with the method specified in ISO 815-1, the compression set shall comply with the requirements of Table 1 after 24 h at 100 C.8.5 Accelerated ageingAfter the test pieces have been aged in accordance with the method specified in ISO 188 and the con

32、ditions specified in Table 2, the change in hardness, tensile strength, and elongation at break shall comply with the requirements of Table 1.8.6 Ozone resistanceWhen tested in accordance with the method specified in ISO 1431-1, test pieces shall show no cracks after 96 h at 40 C, under 20 % elongat

33、ion, at an ozone concentration of 500 ppb.Table 1 Property requirementsProperty UnitLimitDocument specifying test methodType E Type FHardness Shore A 75 5 85 5 ISO 7619-1Tensile strength, min. MPa 12 12 ISO 37Elongation at break, min. % 175 125 ISO 37Compression set, after 24 h at 100 C, max. % 35 3

34、5 ISO 815-1Ozone resistance 500 ppb; elongation 20 %; duration 96 h at 40 C No cracking No cracking ISO 1431-1Maximum change from unaged values after ageing under conditions specified in Table 2:a) hardnessb) tensile strengthc) elongation at breakShore A%+10 to 01540+10 to 01540ISO 188 and ISO 7619-

35、1ISO 188 and ISO 37ISO 188 and ISO 37Table 2 Accelerated ageing test conditionsWorking temperature rangeTest temperature CTest time dP17014P2100P385P4125 ISO 2013 All rights reserved 3BS ISO 5892:2013ISO 5892:2013(E)9 Specific requirements9.1 GeneralThese requirements are optional. Requirements and

36、corresponding test methods shall be the subject of agreement between the interested parties. Requirements specified in 9.2 to 9.8 are summarized in Table 3.9.2 High-density ozone resistanceWhen tested in accordance with the method specified in ISO 1431-1, test pieces shall show no cracks after 96 h

37、at 40 C, under 20 % elongation, at an ozone concentration of 2 000 g/m3.9.3 Holding forceHolding force should be measured according to the method described in Annex A. This method is given as an example. Details of the procedure and requirements depend on the profile of the gasket and shall be the s

38、ubject of agreement between the interested parties.9.4 WatertightnessA suitable test method is described in ISO 15821.9.5 FlammabilityThe flammability of the material shall comply with the requirements of the national regulations regarding the structure of which it is a part.9.6 Contact and migratio

39、n stainingA suitable test method is described in ISO 3865.9.7 Low-temperature brittlenessWhen tested in accordance with the method specified in ISO 812, procedure C, no failure shall be observed in any one of the test pieces at the lowest temperature in thermal conditions of use.9.8 Low-temperature

40、compression setWhen tested in accordance with the method specified in ISO 815-2, the median value of type E compression set after recovery periods of 30 min shall be 80 % or less after 24 h at 25 C. The median value of type F compression set after recovery periods of 30 min shall be 90 % or less aft

41、er 24 h at 25 C.Table 3 Summary of the specific property requirementsProperty UnitLimit Document specifying test methodType E Type FHigh-density ozone resistance 2 000 g/m3; elongation 20 %; duration 96 h at 40 C No cracking ISO 1431-1Holding force N/m Agreement between interested parties Annex AWat

42、ertightness Agreement between interested parties ISO 15821Flammability Requirements of national regulations National regulationsContact and migration staining Agreement between interested parties ISO 38654 ISO 2013 All rights reservedBS ISO 5892:2013ISO 5892:2013(E)Property UnitLimit Document specif

43、ying test methodType E Type FLow-temperature brittleness C Lowest temperature in thermal conditions of use or belowISO 812, procedure CLow-temperature compression set, after 24 h at 25 CMedian value after recovery period of 30 min% 80 % or less 90 % or less ISO 815-2Table 3 (continued) ISO 2013 All

44、rights reserved 5BS ISO 5892:2013ISO 5892:2013(E)Annex A (informative) Holding force testA.1 PrincipleThis test method determines the force exerted by the gaskets to hold glass, etc. It simulates actual use conditions by applying a load to the pressure plate, which is a simulated glass. In the case

45、of double-channel gaskets, place the test pieces between the pressure plate and support frames with thickness equal to that of the articles. In the case of single-channel gaskets, attach the pressure plate and test pieces to the reglets and support frames. Thus, these measurements reflect the wind p

46、ressure that would be encountered during application.A.2 ApparatusA.2.1 The testing machine shall be a power-driven tensile testing machine of the movable crosshead type, equipped with adjustable crosshead speed control, a suitable dynamometer, and an indicating or recording device for measuring the

47、 applied force with an accuracy of 2 % of the full-scale reading.A.2.2 The pressure plate and support frames to be used with the testing machine shall be of a type similar to those shown in Figures A.1 and A.2. The thickness of the support frames and the groove dimensions of the reglets shall be sub

48、ject to actual use conditions.A.2.3 The pressure plate and support frames shall be made of steel. The reglets shall be made of steel or a material equivalent to that of the actual reglets. Their length shall be at least 100 mm.A.3 Test pieceA.3.1 The extruded test pieces shall be at least 50 mm long

49、 but no longer than the pressure plate, support frames, and reglets.A.3.2 A minimum of eight test pieces from each lot shall be tested.A.4 ProcedureA.4.1 Place the test pieces in the support frames as shown in Figures A.1 or A.2. The clearance at this time shall be the subject of agreement between the interested parties. The test shall be conducted at a standard laboratory temperature.A.4.2 Strain the pressure plate at a straining speed of 10 mm/min un