BS ISO 1173-2001 Assembly tools for screws and nuts - Drive ends for hand and machine-operated screwdriver bits and connecting parts - Dimensions torque testing《螺钉和螺母用装配工具 机动和手动旋具类.pdf

《BS ISO 1173-2001 Assembly tools for screws and nuts - Drive ends for hand and machine-operated screwdriver bits and connecting parts - Dimensions torque testing《螺钉和螺母用装配工具 机动和手动旋具类.pdf》由会员分享，可在线阅读，更多相关《BS ISO 1173-2001 Assembly tools for screws and nuts - Drive ends for hand and machine-operated screwdriver bits and connecting parts - Dimensions torque testing《螺钉和螺母用装配工具 机动和手动旋具类.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 1173:2001 Assembly tools for screws and nuts Drive ends for hand and machine-operated screwdriver bits and connecting parts Dimensions, torque testing ICS 25.140.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 1173:2001 This British Standard, h

2、aving been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 July 2001 BSI 07-2001 ISBN 0 580 37710 5 National foreword This British Standard reproduces verbatim ISO 1173:2001 and implements it a

3、s the UK national standard. The UK participation in its preparation was entrusted to Technical Committee MTE/15/13, Assembly tools for screws and nuts, pliers and nippers, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secreta

4、ry. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Ca

5、talogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the

6、text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front

7、cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 8, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsReference nu

8、mber ISO 1173:2001(E) INTERNATIONAL STANDARD ISO 1173 Third edition 2001-04-01 Assembly tools for screws and nuts Drive ends for hand- and machine-operated screwdriver bits and connecting parts Dimensions, torque testing Outils de manuvre pour vis et crous Entranements des embouts tournevis main et

9、machine et lments de connexion Dimensions, couple dessaiISO 1173:2001(E) ii ISO 1173:2001(E)iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carr

10、ied out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

11、ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical commi

12、ttees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. I

13、SO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 1173 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pliers and nippers. This third edition cancels and replaces the second e

14、dition (ISO 1173:1988), which has been technically revised. Annex A of this International Standard is for information only.INTERNATIONAL STANDARD ISO 1173:2001(E)1 Assembly tools for screws and nuts Drive ends for hand- and machine-operated screwdriver bits and connecting parts Dimensions, torque te

15、sting 1 Scope This International Standard specifies the dimensions and torque testing of drive ends for hand- and machine-operated screwdriver bits as well as to driving spindles of screw driving machines. It ensures the interchangeability of tool bits and tool holders. This International Standard d

16、efines only the distinctive features of individual drive ends. Details of design, e.g. of fixing devices, are left to the user of this International Standard. 2 Dimensions See Figures 1 to 8 and Tables 1 to 8. Details not given shall be chosen appropriately.ISO 1173:2001(E) 2 a Retaining system of t

17、he manufacturers choice Figure 1 Male hexagon form A Figure 2 Female hexagon form B Table 1 Male hexagon form A Dimensions in millimetres s 1 d 1 d 3 e 1 l 1 l 3 l 5 r Form Nominal dimension max. min. h9 h12 max. min. min. 0 0,2 0,4 0 min. 3 3 2,96 3,6 3 3,39 3,34 19,5 11,9 7,4 1,00 A 5,5 5,50 5,45

18、6,7 5,7 6,21 6,16 24 16 10,9 1,25 Table 2 Female hexagon form B Dimensions in millimetres s 2 d 2 e 2 l 2 l 4 l 6 Form Nominal dimension max. min. D10 min. 0,1 0,2 0 0 0,4 3 3,06 3,02 3,6 3,41 16,5 11,9 7,2 B 5,5 5,58 5,53 6,7 6,25 21 16 10,7ISO 1173:2001(E)3 Nominal dimension 4 Nominal dimensions 6

19、,3, 8 and 12,5 a 40u u 60 b 80u u 120 a Retaining system of the manufacturers choice. Figure 3 Male hexagon form C Figure 4 Female hexagon form DISO 1173:2001(E) 4 Table 3 Male hexagon form C Dimensions in millimetres s 1 d 3 e 1 l 1 l 3 r Form Nominal dimension max. min. h12 max. min. min. 0 0,2 mi

20、n. 4 3,96 3,91 4,48 4,42 9 4 6,3 6,35 6,29 6,7 7,18 7,11 11 8,2 8 7,93 7,87 8,2 8,96 8,90 13,5 10,2 C 12,5 12,70 12,63 13,5 14,35 14,27 15,9 12,7 0,3 Table 4 Female hexagon form D Dimensions in millimetres s 2 e 2 l 2 l 4 Form Nominal dimension max. min. min. 0,1 0,2 0 4 4,04 3,99 4,51 8 4 6,3 6,45

21、6,39 7,22 10 8,2 8 8,03 7,97 9 12,5 10,2 D 12,5 12,80 12,75 14,4 14,9 12,7 a Retaining system of the manufacturers choice. Figure 5 Male hexagon form E Figure 6 Female hexagon form F Table 5 Male hexagon form E Dimensions in millimetres s 1 d 3 e 1 l 1 l 3 l 7 r Form Nominal dimension max. min. h12

22、max. min. min. 0 0,1 min. 6,3 6,35 6,29 4,7 7,18 7,11 25 9,5 1 2,4 (8) a 7,93 7,87 6,3 8,96 8,90 27 5,4 1,2 2,4 E 11,2 11,11 11,04 8,7 12,56 12,48 31,5 6,7 1,2 2,8 a Non-preferred dimension.ISO 1173:2001(E)5 Table 6 Female hexagon form F Dimensions in millimetres s 2 e 2 l 2 l 4 Form Nominal dimensi

23、on max. min. min. max. 0,1 0 6,3 6,45 6,39 7,22 24 9,5 (8) a 8,03 7,97 9 25,5 5,4 F 11,2 11,23 11,16 12,61 30 6,7 a Non-preferred dimension. a Arrangement with test role for the determination of t hegr o ov ede pt h. a Retaining system of the manufacturers choice. Figure 7 Male flat end form G Figur

24、e 8 Female flat end form H Table 7 Male flat end form G Dimensions in millimetres d 1 d 3 e 1 l 1 l 3 l 5 r Form Nominal dimension f8 h12 max. min. min. 0,2 0,2 min. G 7 7 5,8 3,86 3,74 26 20 14 1,5 Table 8 Female flat end form H Dimensions in millimetres d 2 e 2 l 2 l 4 l 6 Form Nominal dimension H

25、10 0,1 0 max. min. 0,2 H 7 7 4,1 26 20,5 14ISO 1173:2001(E) 6 3 Design Form D Magnetic types for hand-operated screwdriver bits may be manufactured without a bore for a ball or without a groove for a retaining (snap) ring. Form G Male flat ends may also have a V-shaped ring groove instead of a circu

26、lar arc shape ring groove (of the manufacturers choice), which shall comply with the pictorial representation. 4 Designation A drive end conforming to this International Standard shall be designated by a) “Male hexagon“ or “Female hexagon“ in the case of a design with a male or a female hexagon driv

27、e respectively; b) “Male flat end“ or “Female flat end“ in the case of a design with a male or female flat end respectively; c) reference to this International Standard, i.e. ISO 1173; d) capital letter for the respective form (A, B, C, D, E, F, G or H); e) nominal dimension. EXAMPLE 1 A male hexago

28、n Form A of nominal dimension 3 is designated as follows: Male hexagon ISO 1173 - A 3 EXAMPLE 2 A female hexagon Form B of nominal dimension 3 is designated as follows: Female hexagon ISO 1173 - B 3 EXAMPLE 3 A male hexagon Form C of nominal dimension 8 is designated as follows: Male hexagon ISO 117

29、3 - C 8 EXAMPLE 4 A female hexagon Form D of nominal dimension 8 is designated as follows: Female hexagon ISO 1173 - D 8 EXAMPLE 5 A male hexagon Form E of nominal dimension 11,2 is designated as follows: Male hexagon ISO 1173 - E 11,2 EXAMPLE 6 A female hexagon Form F of nominal dimension 11,2 is d

30、esignated as follows: Female hexagon ISO 1173 - F 11,2 EXAMPLE 7 A male flat end Form G of nominal dimension 7 is designated as follows: Male flat end ISO 1173 - G 7 EXAMPLE 8 A female hexagon Form H of nominal dimension 7 is designated as follows: Female flat end ISO 1173 - H 7ISO 1173:2001(E)7 5 T

31、orque testing 5.1 Test piece For torque testing, test devices shall be used which correspond in their dimensions to the respective “counterbodies“ of the connecting parts to be tested. The same dimensional specifications apply to the test pieces as to the connection parts, however, they do not have

32、to be equipped with a retaining system. The torque test device and the test pieces shall have a hardness of at least HRC 62. 5.2 Test values The test torque values for torque testing are given in Table 9. Following the application of the test torque the connecting parts shall show no permanent defor

33、mation or any other damage, such as e.g. cracks or fractures, which might affect the usability of the tool. Table 9 Test torque values Nominal dimension Test torque a min. Form mm N m 37 , 6 A, B 5,5 47 41 8 6,3 71 8 144 C, D 12,5 478 6,3 71 8 144 E, F 11,2 396 G, H 7 25 a The values for the test to

34、rque apply only to connecting parts made of alloyed steel for hardening and tempering or tool steel, heat treated over its whole length, having a hardness of at least HRC 53. When testing with the test torque it shall be ensured that the connecting parts to be tested are engaged under load over thei

35、r whole lengths l 1 and l 2 . The test torque shall be applied smoothly and steadily. Following the application of the minimum test torque, any resulting damage or deformation shall not affect the usability of the tool.ISO 1173:2001(E) 8 Annex A (informative) Explanatory notes In the case of screwdr

36、iver bits and driving spindles of electric and pneumatic screwdrivers driving is performed by hexagon connection or a flat end connection. The interchangeability of tool bits and tool holders is ensured by the standardization of the drive ends. To emphasize the relation between the matching dimensio

37、ns of male and female hexagons or male and female flat ends respectively, this International Standard has been editorially designed such that dimensional letters for male parts have only uneven subscripts (1, 3, 5 .) and for female parts even subscripts (2, 4, 6 .). In order to coordinate the corner

38、 dimensions of the hexagon ends they were calculated according to following formulae: e 1ma x =1,13s 1ma x e 1min =1,13s 1min e 2min =1,13s 2minBS ISO 1173:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing B

39、ritish Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It

40、is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside fron

41、t cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addres

42、sed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless o

43、therwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its produc

44、ts and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Adminis

45、tration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as

46、permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the co

47、urse of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.