BS EN 50318-2002 Railway applications - Current collection systems - Validation of simulation of the dynamic interaction between pantograph and overhead contact line《轨道交通 集流系统 导电弓和.pdf

《BS EN 50318-2002 Railway applications - Current collection systems - Validation of simulation of the dynamic interaction between pantograph and overhead contact line《轨道交通 集流系统 导电弓和.pdf》由会员分享，可在线阅读，更多相关《BS EN 50318-2002 Railway applications - Current collection systems - Validation of simulation of the dynamic interaction between pantograph and overhead contact line《轨道交通 集流系统 导电弓和.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 50318:2002 Railway applications Current collection systems Validation of simulation of the dynamic interaction between pantograph and overhead contact line The European Standard EN 50318:2002 has the status of a British Standard ICS 29.280 BS EN 50318:2002 This British Standar

2、d, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 11 October 2002 BSI 11 October 2002 ISBN 0 580 40560 5 National foreword This British Standard is the official

3、 English language version of EN 50318:2002. The UK participation in its preparation was entrusted to Technical Committee GEL/9, Railway electrotechnical applications, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. C

4、ross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or

5、of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text;

6、 present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover

7、, an inside front cover, the EN title page, pages 2 to 16, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 50318 NORME EUROPENNE EUROPI

8、SCHE NORM July 2002 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2002 CENELEC - All rights of exploitation in any form and by

9、 any means reserved worldwide for CENELEC members. Ref. No. EN 50318:2002 E ICS 29.280 English version Railway applications - Current collection systems - Validation of simulation of the dynamic interaction between pantograph and overhead contact line Applications ferroviaires - Systmes de captage d

10、e courant - Validation des simulations de linteraction dynamique entre le pantographe et la catnaire Bahnanwendungen - Stromabnahmesysteme - Validierung von Simulationssystemen fr das dynamische Zusammenwirken zwischen Stromabnehmer und Oberleitung This European Standard was approved by CENELEC on 2

11、002-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may b

12、e obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to th

13、e Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovaki

14、a, Spain, Sweden, Switzerland and United Kingdom.EN 50318:2002 2 Foreword This European Standard was prepared by SC 9XC, Electric supply and earthing systems for public transport equipment and ancillary apparatus (fixed installations), of Technical Committee CENELEC TC 9X, Electrical and electronic

15、applications for railways. The text of the draft was submitted to the formal vote and was approved by CENELEC as EN 50318 on 2002-04-01. The following dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endors

16、ement (dop) 2003-04-01 - latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2005-04-01 Annexes designated “normative“ are part of the body of the standard. In this standard, annex A is normative This European Standard has been prepared under a mandate give

17、n to CENELEC by the European Commission and supports the Interoperability Directive, 96/48/EC. _ 3 EN 50318:2002 Contents Page 1 Scope .4 2 Normative references4 3 Definitions .4 4 Symbols 6 5 General .6 6 Modelling of the pantograph 8 6.1 General requirements.8 6.2 Minimum data8 7 Modelling of the

18、overhead contact line8 7.1 General requirements.8 7.2 Minimum data9 8 Parameters of simulation.9 9 Output.10 9.1 Contact force. 10 9.2 Wire displacement 10 9.3 Pantograph displacement10 9.4 Loss of contact 10 10 Validation with measured values 11 10.1 Comparison values. 11 10.2 Limits of validation

19、.11 11 Reference model 12 11.1 Purpose of reference model 12 11.2 Reference model data 12 11.3 Reference model results . 13 Annex A (normative) Reference model specification 14 A.1 Pantograph data. 14 A.2 Overhead contact line data 15 A.3 Parameters of simulation.16 Figure 1 - Steps of evaluation7 F

20、igure A.1 - Pantograph model .14 Figure A.2 - Catenary system15 Table 1 - Deviation of simulated values.11 Table 2 - Ranges of results from reference model .13 Table A.1 - Pantograph data .14 Table A.2 - Position of droppers 15 Table A.3 - Mechanical values of wires15EN 50318:2002 4 1 Scope This Eur

21、opean Standard specifies functional requirements for the validation of simulation methods to ensure mutual acceptance of input and output parameters; a standardized subset of test results for evaluation of simulation methods; comparison with measurements; comparison between simulation methods. This

22、standard applies to the current collection from an overhead contact line by pantographs mounted on railway vehicles. It does not apply to trolley bus systems. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normativ

23、e references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated referen

24、ces the latest edition of the publication referred to applies (including amendments). EN 50206-1 Railway applications Rolling stock Pantographs: Characteristics and tests Part 1: Pantographs for main line vehicles EN 50317 Railway applications Current collection systems Requirements for and validati

25、on of measurements of the dynamic interaction between pantograph and overhead contact line 3 Definitions For the purpose of this standard the following definitions apply: 3.1 contact point point of mechanical contact between a contact strip and a contact wire 3.2 contact force vertical force applied

26、 by the pantograph to the overhead contact line. The contact force is the sum of the forces of all contact points 3.3 static force mean vertical force exerted upward by the collector head on the overhead contact line, and caused by the pantograph raising device, whilst the pantograph is raised and t

27、he vehicle is at standstill EN 50206-1 3.4 aerodynamic force vertical force applied to the pantograph as a result of air flow around the pantograph components 5 EN 50318:2002 3.5 mean value of contact force F M arithmetic mean of contact force 3.6 standard deviation of contact force square root of t

28、he sum of the square errors divided by the number of output values minus 1 3.7 statistical minimum of contact force value of contact force represented by F M 3 3.8 statistical maximum of contact force value of contact force represented by F M+ 3 3.9 minimum of contact force minimum contact force whi

29、le the pantograph passes over the analysis section 3.10 maximum of contact force maximum contact force while the pantograph passes over the ananlysis section 3.11 loss of contact condition when the contact force is zero 3.12 simulation method any numerical method that uses a fixed set of input param

30、eters describing a system (e.g. pantograph/overhead contact line system) to calculate a set of output values representative of the dynamic behaviour of this system 3.13 pantograph model mathematical model describing the dynamic characteristics of the pantograph 3.14 massspringdampermodel method repr

31、esenting a dynamic mechanical system (e.g. pantograph) as a series of discrete concentrated masses connected together by spring and damper elements 3.15 transfer function of a pantograph ratio of an applied force to the response of the pantograph, depending on frequency. For example the apparent mas

32、s function, as ratio of an applied sinusoidal force to the corresponding acceleration 3.16 collector head part of the pantograph supported by the frame, which includes contact strips, horns and may include a suspensionEN 50318:2002 6 3.17 overhead contact line model mathematical model in a two- or t

33、hree-dimensional geometry describing the dynamic characteristics of an overhead contact line 3.18 wave propagation speed of the contact wire speed of a transversal wave, which runs along the contact wire 3.19 maximum uplift at the support maximum value of the vertical uplift at each support within t

34、he analysis section, while the pantograph passes 3.20 analysis section subset of the total overhead contact line model length which consists of those parts over which the passage of the pantographs is not influenced by initial transients and end effects of the model 3.21 frequency range of interest

35、frequency range within which the dynamic performance of the overhead contact line pantograph system is considered 4 Symbols F M mean value of contact force standard deviation of contact force 5 General The theoretical study of the dynamic interaction between pantograph and overhead contact line by c

36、omputer simulation makes it possible, to obtain much information about the system and to minimise the costs of line tests. Depending on the phenomena to be studied, the frequency range of interest shall be defined in advance and shall be consistent with the pantograph model, overhead contact line mo

37、del and simulation method and with the measurement system. The simulation method shall be assessed by the use of comparisons between the results of the simulation and line tests or by comparison with other validated simulation methods. A validation of the method shall be done in accordance with clau

38、se 10. In order to be used with confidence the simulation method shall be evaluated. The evaluation for a simulation method shall be done with the two steps which are shown in Figure 1. 7 EN 50318:2002 Start validation Benchmark with reference model (see clause 11) Unchecked simulation method line t

39、est results conditions X n Step 1 validated simulation method validation acc. to sublause 10.1 for conditions X n step 2 validated simulation method for condition X n usable in ranges acc. to subclause 10.2 further conditions End validation 2 1 1 1 2 simulation input for conditions X nacc. to clause

40、 6,7,8 n n y n y validation step 1 validation step 2 y Figure 1 Steps of evaluation subclauseEN 50318:2002 8 6 Modelling of the pantograph 6.1 General requirements A pantograph model shall describe the dynamic characteristics of a pantograph in the frequency range of interest. NOTE Possible modellin

41、g methods are discrete mass-spring-damper-models, multi-body systems, finite-element-models or the transfer function of the pantograph. The characteristics of control and the dynamic characteristics of active pantographs shall be available for the modelling method. 6.2 Minimum data The following par

42、ameters of the pantograph shall be available for simulation: kinematics; mass distribution; degree of freedom of joints; damping characteristics; spring characteristics; friction values; stiffness; bump stops; location of application of the static force; location of application of the aerodynamic fo

43、rces. NOTE Aerodynamic forces usually depend on the orientation, operation height and position of the pantograph and the type of train. These parameters shall take into account other dependencies (operation height, stagger, non-linearities, frequency), if required. 7 Modelling of the overhead contac

44、t line 7.1 General requirements The model of the overhead contact line shall describe the dynamic characteristics in the frequency range of interest. The overhead contact line may be modelled with two- or three-dimensional geometry, depending on the phenomena to be investigated. If required, the ove

45、rhead contact line model shall be modelled including all tensioning equipment or any discrete components such as section insulators, insulated overlaps or others. 9 EN 50318:2002 7.2 Minimum data The following geometrical and mechanical parameters of an overhead contact line shall be available for s

46、imulation: length of overhead contact line model. The length of the overhead contact line model shall be at least three times the spacing between the first and last pantograph, with a minimum of 10 spans; length of each span; position of droppers; contact wire height (sag, dropper length, wire gradi

47、ents); encumbrance at the supports; geometry and mass distribution of steady arms; stagger; number and characteristics of wires (contact wire, catenary wire, auxiliary wire, stitch wire, droppers, ); mass per unit length of the wires or density and cross-section; mechanical tension of wires. Where t

48、he tension depends on temperature, this relationship shall be specified; mass of links between wires and droppers (clamps); the mechanical characteristics of the supports and structures; the stiffness characteristic of droppers. 8 Parameters of simulation The parameters of the pantograph and overhea

49、d contact line shall be given according to clauses 6 and 7. In addition, the following parameters shall be defined if applicable: train speed; analysis section; number of and distances between pantographs; static force of each pantograph; aerodynamic forces of each pantograph; operation height of the pantograph; wire temperatures; damping of the overhead contact li