BS EN 949-1999 Windows and curtain walling doors blinds and shutters - Determination of the resistance to soft and heavy body impact for doors《窗和窗帘墙 门 遮帘和百叶窗 对撞击于门的软和重的物体抗性的测定》.pdf

《BS EN 949-1999 Windows and curtain walling doors blinds and shutters - Determination of the resistance to soft and heavy body impact for doors《窗和窗帘墙 门 遮帘和百叶窗 对撞击于门的软和重的物体抗性的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 949-1999 Windows and curtain walling doors blinds and shutters - Determination of the resistance to soft and heavy body impact for doors《窗和窗帘墙 门 遮帘和百叶窗 对撞击于门的软和重的物体抗性的测定》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 949:1999 The Europe

2、an Standard EN 949:1998 has the status of a British Standard ICS 91.060.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Windows and curtain walling, doors, blinds and shutters Determination of the resistance to soft and heavy body impact for doorsThis British Standard, havi

3、ng been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 May 1999 BSI 05-1999 ISBN 0 580 32280 7 BS EN 949:1999 Amendments issued since publication Amd. No. Date Text affe

4、cted National foreword This British Standard is the English language version of EN 949:1998. The UK participation in its preparation was entrusted to Technical Committee B/538, Doors, windows, shutters, hardware and curtain walling, which has the responsibility to: aid enquirers to understand the te

5、xt; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obta

6、ined on request to its secretary. This British Standard forms part of a package of standards on doors which will not become fully effective until all standards in the package have been published and any superseded standards have been withdrawn. The date of withdrawal for national standards will be a

7、greed within CEN and will be notified. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Fi

8、nd” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from lega

9、l obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: ru

10、e de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 949:1998 E EUROPEAN STANDARD EN 949 NORME EUROPE ENNE EUROPA ISCHE NORM December 1998 ICS 91.060.50 Supersedes EN 162:1985 Descriptors: windows,

11、 doors, blinds, closures, tests, mechanical strength, shock resistance English version Windows and curtain walling, doors, blinds and shutters Determination of the resistance to soft and heavy body impact for doors Fene tres et fac ades-rideaux, portes, stores et fermetures De termination de la re s

12、istance au choc de corps mou et lourd pour les portes Fenster, Tu ren, Dreh- und Rolla den, Vorhangfassaden Ermittlung der Widerstandsfa higkeit von Tu ren gegen Aufprall eines weichen und schweren Stoko rpers This European Standard was approved by CEN on 26 November 1998. CEN members are bound to c

13、omply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central

14、Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the

15、official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 949:1998 BSI 05-1999 Foreword T

16、his European Standard has been prepared by Technical Committee CEN/TC 33, Doors, windows, shutters and building hardware, the Secretariat of which is held by AFNOR. This European Standard replaces EN 162:1985. This European Standard shall be given the status of a national standard, either by publica

17、tion of an identical text or by endorsement, at the latest by June 1999, and conflicting national standards shall be withdrawn at the latest by December 1999. This standard is one of a series of standards for doors. The test method relates to performance requirements to be published in EN 1192, Door

18、s Mechanical strength Requirements and classification. This standard has been prepared taking into account ISO 8270 and EN 162. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, B

19、elgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Page 3 EN 949:1998 BSI 05-1999 Introduction For manufacturers of door leaves whose products are not sold as part of

20、 a known doorset, or where such door leaves can be used in a sliding door assembly, provision is made for claiming compliance with the relevant requirements by the testing of such door leaves in a typical frame. Nevertheless, the fact that a particular door leaf meets with the relevant requirements

21、in this way does not necessarily mean that a door assembly incorporating that door leaf will meet the requirements. 1 Scope This European standard applies to all doors. The standard specifies the method to be used to determine the damage caused by striking with a soft and heavy body, the face of a c

22、losed door leaf fixed in its own door frame as part of a doorset. NOTE Such forces that might reasonably be expected from impacts by human bodies and substantial objects with similar characteristics should neither damage, nor impair the normal performance of, a door. The method may also be used in r

23、espect of a door leaf submitted for test in a frame which the manufacturer considers appropriate to and typical for the intended utilization. 2 Apparatus 2.1 Test surround, a surround in which the specimen is tested, which shall be sufficiently rigid to withstand the test load without deflecting to

24、an extent likely to influence the test result. 2.2 Impact equipment, impact body of total mass (30 0,6 )kg, consisting of a spherical leather bag of diameter approximately 350 mm, containing dry sand of apparent density approximately 1500 kg/m 3 which passes through a sieve of 2 mm mesh. Wires, pull

25、eys, release hook and suitable heightregulating devices. 2.3 Measuring equipment, a dial or digital gauge accurate to 0,01 mm, mounted at the centre of a reference bar capable of spanning the width of the door leaf. 3 Test specimens Test specimens shall be stored and tested in a nondestructive envir

26、onment within the ranges of 158C to 308C and 25 % to 75 % relative humidity. Doors which are designed to be glazed, shall be supplied for testing with all glazing carried out in accordance with the door manufacturers specification. 4 Procedure The door leaf to be tested shall be closed and where app

27、licable secured in accordance with its normal operating mode. NOTE 1 In its normal operating mode a door leaf can be unsecured, or secured by latch, lock, bolt or other means. Identify the impact point. This shall occur at the centre of the door leaf. Where the impact point coincides with the handle

28、, this shall be removed. With the reference bar, measure any deviation in flatness across the width of the door leaf at the height of the impact point, to the nearest 0,1 mm. Suspend the impact body as shown in Figure 1 so that at rest it makes light contact with the surface of the door leaf and so

29、that its centre of gravity is positioned on a line perpendicular to the door leaf at its centre. Raise the impact body so that the drop height h, with a tolerance of 10 mm, corresponds to the required impact energy. Release the impact body such that it strikes the door leaf at the impact point. NOTE

30、 2 Repetition of this operation will necessitate re-shaping of the impact body. Repeat the measurement of deviation in flatness across the width of the door leaf at the height of the impact point, to the nearest 0,1 mm. 5 Expression of results Record: the residual deformation in flatness, across the

31、 width at the height of the impact point. 6 Test report The test report shall contain the following information: a) reference to this European Standard; b) all necessary details to identify the doorset or door leaf; c) all relevant details concerning the type, specified dimensions, materials, form a

32、nd construction of the doorset or door leaf, including the position of hardware; d) full details of the frame and hardware supplied if the assembly is not a doorset; e) the position and size of any glazed or panelled areas; f) laboratory storage and testing conditions; g) the face or faces tested an

33、d number of impacts applied to each face; h) the impact energy in joules; i) the results expressed as in clause 5; j) details of any damage that appeared during the test; k) name of testing laboratory; l) date of test.Page 4 EN 949:1998 BSI 05-1999 1 pulley; 2 wire; 3 drop height, h 10 mm; 4 release

34、 hook; 5 regulating device; 6 impact body; 7 doorset; 8 test rig. Figure 1 Apparatus for soft and heavy body impact test and test principleblankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

35、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europ

36、e and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our produc

37、ts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers mem

38、bers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 700

39、1. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standa

40、rds through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to d

41、ate with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright,

42、 in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise wi

43、thout prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.