BS EN 4593-2011 Aerospace series Paints and varnishes Determination of solar absorptance《航空航天系列 色漆和清漆 太阳能吸收率的测定》.pdf

《BS EN 4593-2011 Aerospace series Paints and varnishes Determination of solar absorptance《航空航天系列 色漆和清漆 太阳能吸收率的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 4593-2011 Aerospace series Paints and varnishes Determination of solar absorptance《航空航天系列 色漆和清漆 太阳能吸收率的测定》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 4593:2011Aerospace series Paints andvarnishes Determination ofsolar absorptanceBS EN 4593:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementati

2、on of EN 4593:2011.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/65, Non-metallic materials for aerospace purposes(excluding textiles).A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport

3、to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 73663 6ICS 49.040Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Poli

4、cy and Strategy Committee on 31 July 2011.Amendments issued since publicationDate Text affectedBS EN 4593:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4593 June 2011 ICS 49.040 English Version Aerospace series - Paints and varnishes - Determination of solar absorptance Srie arospatiale -

5、 Peintures et vernis - Dtermination de labsorption solaire Luft- und Raumfahrt - Beschichtungsstoffe - Bestimmung der Sonnenlichtabsorption This European Standard was approved by CEN on 19 February 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the co

6、nditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exi

7、sts in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national st

8、andards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland an

9、d United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4593:2

10、011: EBS EN 4593:2011EN 4593:2011 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Definitions 4 4 Principle 4 5 Apparatus .4 6 Specimens 5 7 Procedure .5 8 Calculation 5 9 Supplementary information 6 10 Test report 6 11 Designation 6 BS EN 4593:2011EN 4593:2011 (E) 3 Foreword Thi

11、s document (EN 4593:2011) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the

12、 Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2011, and conflicting national standards shall be with

13、drawn at the latest by December 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulation

14、s, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, N

15、etherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 4593:2011EN 4593:2011 (E) 4 1 Scope This European Standard specifies the method of test for determining the solar absorptance of paints and varnishes. The test procedure determ

16、ines the amount of energy reflected by the material in the range of wavelengths at which there is energy from the sun hitting the Earths surface, and with the aid of a standard solar spectrum it allows a calculation to determine the solar absorptance which can then be used to determine the efficienc

17、y of solar heat reflecting paints. The procedure is applicable to products intended for use in aerospace applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated r

18、eferences, the latest edition of the referenced document (including any amendments) applies. EN 23270, Paints and varnishes and their raw materials Temperatures and humidities for conditioning and testing (ISO 3270:1984) EN ISO 15528, Paints, varnishes and raw materials for paints and varnishes Samp

19、ling (ISO 15528:2000) EN ISO 1513, Paints and varnishes Examination and preparation of test samples (ISO 1513:2010) EN ISO 2808, Paints and varnishes Determination of film thickness (ISO 2808:2007) CIE publ No 85, Solar spectral irradiance 3 Definitions For the purposes of this document, the followi

20、ng terms and definitions apply. 3.1 solar absorptance proportion of the energy emitted by the sun which hits the Earths surface which is absorbed by the material under test 4 Principle The reflectance of specimens, comprising of coated test panels is measured and summated over the range of solar ene

21、rgy which hits the Earths surface through two air masses, allows the calculation of solar absorptance. 5 Apparatus A recording spectrophotometer fitted with an integrating sphere which has the specular component included, a 10/diffuse measuring geometry and is capable of meeting the following requir

22、ements. Measuring range: 300 nm to 2 300 nm Wavelength accuracy: 5 nm Measuring accuracy: 2 % BS EN 4593:2011EN 4593:2011 (E) 5 Bandpass: 4 nm Replace (23 2) C and (50 5) % relative humidity with EN 23270, where applicable. 6 Specimens Take a representative sample of the product to be tested or of e

23、ach component in the case of a multi-coat system as described in EN ISO 15528. Examine and prepare each sample for testing as described in EN ISO 1513. The test panels shall be of a size suitable for the performance of the tests identified by this and the product standard. Coat the test panels with

24、the test product as specified by the product standard. Dry/cure the coating for the time and under the conditions specified in the product standard. The coating thickness, when determined using one of the non destructive procedures specified in EN ISO 2808 shall comply with the requirements of the p

25、roduct standard. Condition the test panels at a temperature and at a relative humidity of EN 23270 for a minimum of 16 h and a maximum of 72 h prior to testing. 7 Procedure Measure and record the reflectance spectrum using the reflectance grade barium sulphate as the reflectance standard on the spec

26、trophotometer in the wavelength range 300 nm to 2 300 nm. 8 Calculation Unless specified, use the solar spectral irradiance data (CIE publ No 85) through 2 air masses, 0,2 nm optical depth at 50 nm, 0,3 cm ozone and 2,0 cm precipitable water. Calculate the solar absorptance using the following equat

27、ion: =30023003002300100100m)(sR where (s) is the solar absorptance; Rmis the measured reflectance of paint, as a percentage; is the solar irradiance, in watt per square metre. BS EN 4593:2011EN 4593:2011 (E) 6 9 Supplementary information In the performance of this test standard there is a requiremen

28、t for supplementary information to be provided by the product standard for the material under test. This information consists of: a) substrate type and method of preparation; b) method of application of the coating including, where applicable, the duration and conditions of drying/curing between coa

29、ts in the case of multi-coat systems; c) duration and conditions of drying/curing of the final coat before test; d) thickness of the dry coating or combination of coatings in micrometres; e) properties of the coating to be evaluated following exposure; f) number of air masses to employ for standard

30、solar spectrum. 10 Test report The test report shall contain at least the following information: a) all details necessary to identify the product tested; b) a reference to this test standard; c) a reference to the product standard; d) the items of supplementary information (see clause 9); e) the res

31、ults of the test work in terms of the stated requirements; f) any deviation from the test method specified; g) the date(s) of the test; h) name of the operator. 11 Designation EXAMPLE Description blockDETERMINATION OF SOLAR ABSORPTANCE Identity block EN 4593 Number of this standard This page deliber

32、ately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Ins

33、titution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the

34、constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover

35、.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy v

36、ersions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international st

37、andards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 89

38、96 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substan

39、tial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information ab

40、out BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored

41、in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: