BS 5793-6-1986 Industrial-process control valves - Specificaton for mounting details for attachment of positioners to control valve actuators《工业过程控制阀 定位器控制阀引动器附件安装详细规范》.pdf
《BS 5793-6-1986 Industrial-process control valves - Specificaton for mounting details for attachment of positioners to control valve actuators《工业过程控制阀 定位器控制阀引动器附件安装详细规范》.pdf》由会员分享,可在线阅读,更多相关《BS 5793-6-1986 Industrial-process control valves - Specificaton for mounting details for attachment of positioners to control valve actuators《工业过程控制阀 定位器控制阀引动器附件安装详细规范》.pdf(14页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD CONFIRMED SEPTEMBER 1992 BS 5793-6: 1986 IEC 534-6: 1985 Industrial-process control valves Part 6: Specification for mounting details for attachment of positioners to control valve actuators UDC 66.025:621.646.3:681.533.3BS5793-6:1986 This British Standard, having been prepared unde
2、r the direction of the Industrial-process Measurement and Control Standards Committee, was published under the authority of the Board of BSI and comes into effect on 28November1986 BSI 08-1999 The following BSI references relate to the work on this standard: Committee reference PCL/1 Draft for comme
3、nt 82/32597 DC ISBN 0 580 15529 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Industrial-process Measurement and Control Standards Committee (PCL/-) to Technical Committee PCL/1, upon which the following bodies were represented: Brit
4、ish Coal British Gas Corporation British Pressure Gauge Manufacturers Association Department of Energy (Gas and Oil Measurement Branch) Department of Trade and Industry (National Weights and Measures Laboratory) Energy Industries Council Engineering Equipment and Materials Users Association GAMBICA
5、(BEAMA Ltd.) Health and Safety Executive Institution of Gas Engineers The following bodies were also represented in the drafting of the standard, through subcommittees and panels: British Chemical Engineering Contractors Association British Valve Manufacturers Association Ltd. Electricity Supply Ind
6、ustry in England and Wales Amendments issued since publication Amd. No. Date of issue CommentsBS5793-6:1986 BSI 08-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope and object 1 2 Definitions 1 3 Basic design principles 1 4 Feedback connection 1 5 Mounting p
7、late design 2 6 Actuator mounting 2 7 Mounting accessories 2 Figure 1 3 Figure 2 4 Figure 3 5 Figure 4 5 Figure 5 6 Figure 6 7 Publications referred to Inside back coverBS5793-6:1986 ii BSI 08-1999 National foreword This Part of BS5793 has been prepared under the direction of the Industrial-process
8、Measurement and Control Standards Committee. It is identical with IEC Publication534-6:1985 “Industrial-process control valves. Part6: Mounting details for attachment of positioners to control valve actuators” published by the International Electrotechnical Commission (IEC). Terminology and conventi
9、ons. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. The comma has been used
10、as a decimal marker in Figure 3 to Figure 6. In BritishStandards it is current practice to use a full point on the baseline. Wherever page numbers are quoted, they are IEC page numbers. The reference to “other parts of IEC Publication534” in clause2 should be read as “other Parts of BS5793”. A Briti
11、sh Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front
12、 cover, an inside front cover, pages i and ii, pages1to8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS5793-6:1986 BSI 08-1999 1 1 Scope a
13、nd object This standard is intended to permit a variety of positioning devices which respond to a linear motion to be mounted on the actuator of a control valve, either directly or by employing an intermediate mounting bracket. There is a large variety of types, sizes and designs of actuators. The f
14、ollowing parameters define the intended applicability of this standard for the guidance of manufacturers and users. 1.1 The standardized mounting applies only to positioners which are mounted on the side of the actuator. 1.2 The standardized mounting applies in general only to those actuators which
15、have a travel of100mm or less. 1.3 The standardized mounting is designed to cover three basic types of actuator design (see Figure 1, page3): a) those with some form of cast or fabricated yoke to connect the actuator power unit to the valve; b) those which use some form of central tube yoke to conne
16、ct the actuator power unit to the valve; c) those in which the yoke incorporates two or more columns or pillars to connect the actuator power unit to the valve. 2 Definitions All of the definitions given in other parts of IEC Publication534shall apply, with the addition of the following. 2.1 actuato
17、r a device or mechanism which changes a signal into a corresponding movement controlling the position of the internal regulating mechanism of the control valve NOTE 1The signal or energizing force may be pneumatic, electric, hydraulic, or any combination thereof. NOTE 2The actuator comprises an actu
18、ator power unit and a yoke for attachment to the control valve. The yoke may take the form of a casting, a central tube, two or more pillars, or it may be fabricated from stampings (see Figure 1). 2.2 actuating power unit the part of the actuator which converts fluid, electrical, thermal or mechanic
19、al energy into stem motion to develop thrust or torque 2.3 yoke the structure which rigidly connects the actuator power unit to a valve NOTEThe yoke may be an integral part of the actuator power unit in some actuator designs. 2.4 actuator stem the bar or rod between the actuator and the valve which
20、ultimately operates the internal regulating mechanism 3 Basic design principles The objective is to standardize the attachment of the positioner to the side of the actuator to assure compatibility of products from different manufacturers. 3.1 For this purpose the manufacturer of the actuator shall o
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS579361986INDUSTRIALPROCESSCONTROLVALVESSPECIFICATONFORMOUNTINGDETAILSFORATTACHMENTOFPOSITIONERSTOCONTROLVALVEACTUATORS
链接地址:http://www.mydoc123.com/p-545399.html