BS 341-4-2004 Transportable gas container valves - Pressure relief devices《可运输气体容器的阀门 减压装置》.pdf

《BS 341-4-2004 Transportable gas container valves - Pressure relief devices《可运输气体容器的阀门 减压装置》.pdf》由会员分享，可在线阅读，更多相关《BS 341-4-2004 Transportable gas container valves - Pressure relief devices《可运输气体容器的阀门 减压装置》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 341-4:2004 Transportable gas container valves Part 4: Pressure relief devices ICS 23.060.40 BS 341-4:2004 This British Standard, having been prepared under the direction of the Standards Policy and Strategy Committee, was published on 15 January 2004 BSI 15 January 2004 The follo

2、wing BSI references relate to the work on this British Standard Committee reference PVE/3/1 Draft for comment 00/716619 DC ISBN 0 580 43113 4 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee, PVE/3, Gas containers, to Subc

3、ommittee PVE/3/1, Valve fittings for gas cylinders, upon which the following bodies were represented: British Compressed Gases Association DoH Medical Devices Agency Health and Safety Executive Home Office L P Gas Association Ministry of Defence Personal Safety Manufacturers Association Scuba Indust

4、ries Trade Association Ltd. Amendments issued since publication Text Amd No. CommentsBS 341-4:2004 BSI 15 January 2004 i Contents Committees responsible Inside front cover Foreword ii 1S c o p e 1 2 Normative references 1 3T e r m s a n d d e f i n i t i o n s 1 4 Design of pressure relief devices 2

5、 5R e l i e f p r e s s u r e 3 6 Bursting disc test 3 7 Installation and application of pressure relief devices 3BS 341-4:2004 ii BSI 15 January 2004 Foreword This part of BS 341 has been prepared by Subcommittee PVE/3/1 on behalf of Technical Committee PVE/3 and partially supersedes BS 341-1:1991,

6、 which is obsolescent. BS 341-1:1991 detailed all aspects of the design, manufacture and testing of valves fitted to containers used for the conveyance of permanent, liquefiable and dissolved gases, except those for liquefied petroleum gas (LPG) applications. The scope of the 1991 version has been p

7、rogressively superseded by a series of standards originating in the European Committee for Standardization (CEN). This part of BS 341 has been issued to cover requirements for pressure relief devices. However, it is anticipated that it will be withdrawn on the publication of a future CEN standard on

8、 this subject. BS 341, Transportable gas container valves, is published in four parts: Part 1: Specification for industrial valves for working pressures up to and including 300 bar (obsolescent); Part 2: Valves with taper stems for use with breathing apparatus (obsolescent); Part 3: Valve outlet con

9、nections; Part 4: Pressure relief devices. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This d

10、ocument comprises of a front cover, an inside front cover, pages i and ii, pages 1 to 3 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.BS 341-4:2004 BSI 15 January 2004 1 1 Scope This part of BS 341 specifies requirements for the des

11、ign and application of pressure relief devices for use with transportable gas cylinders manufactured for conveyance and storage of compressed, liquefied and dissolved gases for industrial and medical applications. This part of BS 341 does not include requirements for pressure relief devices for liqu

12、efied petroleum gas (LPG). This part of BS 341 applies to pressure relief devices for containers limited to a charging pressure of 300 bar) 1)gauge. (Developed pressures for particular gases may exceed this pressure.) 2 Normative references The following referenced documents are indispensable for th

13、e application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. BS 2915:1990, Specification for bursting discs and bursting disc devices. BS EN 1802, Transportable gas cyli

14、nders Periodic inspection and testing of seamless aluminium gas cylinders. BS EN 1803, Transportable gas cylinders Periodic inspection and testing of welded carbon steel gas cylinders. BS EN 1968, Transportable gas cylinders Periodic inspection and testing of seamless steel gas cylinders. BS EN 1286

15、3, Transportable gas cylinders Periodic inspection and maintenance of dissolved acetylene cylinders. BS EN ISO 11114-1, Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials. BS EN ISO 11114-2, Transportable gas cylinders Compatibility

16、 of cylinder and valve materials with gas contents Part 2: Non-metallic materials. BS EN ISO 14246, Transportable gas cylinders Gas cylinder valves Manufacturing tests and inspections. 3 Terms and definitions For the purposes of this part of BS 341, the following terms and definitions apply. 3.1 pre

17、ssure relief device device designed to reduce the possibility of failure of a charged container from excessive pressure particularly when the container is exposed to heat 3.2 pressure relief valve pressure relief device that is in direct contact with the gas, and is designed to open and close within

18、 predetermined pressure limits 3.3 bursting disc pressure relief device consisting of a disc that is in direct contact with the gas and is designed to rupture between predetermined pressure limits 3.4 fusible plug device containing a material of low melting point which is intended to yield or melt w

19、ithin predetermined limits of temperature and permit the discharge of the contained gas 1) 1 bar = 10 5N/m 2= 100 kPa.BS 341-4:2004 2 BSI 15 January 2004 3.5 flow rating pressure pressure at the inlet of a pressure relief device which is used for establishing its rated flow capacity 3.6 rated flow c

20、apacity capacity of a pressure relief device measured in cubic metres per minute of free air at the designed flow rating pressure 3.7 specified bursting pressure nominal pressure at which a bursting disc is designed to rupture 3.8 maximum bursting pressure specified bursting pressure plus the upper

21、permitted design tolerance 3.9 leakage unintended flow of gas or liquid in excess of 5 mbar l/h 2)4 Design of pressure relief devices 4.1 There shall be no significant change in the function of the device and no detrimental corrosion or deterioration of the materials due to normal service conditions

22、 of the container to which it is fitted within the following period. For valves fitted to seamless steel containers (excluding dissolved acetylene containers) of water capacity 0.5 l and above, the inspection periods shall be as specified in BS EN 1968. For valves fitted to welded steel containers (

23、excluding dissolved acetylene containers) of water capacity 0.5 l up to 150 l, the inspection periods shall be as specified in BS EN 1803. For valves fitted to seamless aluminium alloy containers (excluding dissolved acetylene containers) of water capacity 0.5 l and above, the inspection periods sha

24、ll be as specified in BS EN 1802. For valves fitted to dissolved acetylene containers, the inspection periods shall be as specified in BS EN 12863. 4.2 The breakage or failure of any internal component shall not obstruct free and full discharge of the gas through the pressure relief device. 4.3 The

25、materials of construction shall be mutually compatible and compatible with the gas(es) to be conveyed (see BS EN ISO 11114-1 and BS EN ISO 11114-2) and other service conditions, e.g. to prevent room temperature bonding of relief valve seat pads to relief valve seats. 4.4 The design shall be such as

26、to deter tampering. 4.5 The outlets from all pressure relief devices shall be so designed and constructed as to minimize the collection of moisture or other foreign matter that could adversely affect the performance of the device. The outlets from all pressure relief devices shall be so sited that f

27、ree discharge from the devices is not impaired, and the jet thrust effect of such discharges does not impose destabilizing forces on the container. 4.6 All pressure relief devices shall be designed and fitted so as to ensure that the cooling effect of the discharge does not prevent the effective ope

28、ration of the devices. 4.7 Pressure relief devices shall be sized to be capable, under the most severe design requirements (e.g. exposure to fire), of a discharge rate that prevents the pressure of the container contents exceeding the test pressure of the container. The minimum rated flow capacity f

29、or pressure relief devices fitted to non-insulated containers having water capacities of 11 l or more shall be as follows. 2) 5 mbarl/h . 10 3torrl/s = 133.3 10 6Nm/s. An approximate indication of this leakage rate would be the formation of four 3.5 mm diameter or ten 2.5 mm diameter bubbles per min

30、ute.BS 341-4:2004 BSI 15 January 2004 3 a) For compressed gases: Q 1= 0.00967W c where Q 1is the rated flow capacity in cubic metres per minute of free air at 7 bar absolute; W c is the water capacity of the container in litres. b) For liquefied gases: the rated flow capacity of the pressure device

31、shall be twice that given by the equation in item a). For containers having water capacities of less than 11 l, the rated flow capacity shall be as given in items a) and b), except that the value of W cshall be 11, i.e. the rated flow capacity shall be 0.106 37 m 3 /min. 4.8 The yield temperature fo

32、r fusible plugs used with acetylene containers shall be (100 2) C. 4.9 The methods of manufacture, inspection and test shall conform to those of the valve, as specified in BS EN ISO 14246. 4.10 Bursting discs shall conform to BS 2915:1990, except that flat discs may be used, and shall be designed so

33、 as to ensure that rupture occurs at a pressure not greater than the test pressure of the container. If a container is liable to be subject to vacuum conditions during service, the bursting disc shall be fitted with vacuum supports. NOTE Where flat discs are used, special measures should be taken in

34、 valve production to ensure it is not possible for more than one disc to be fitted to a valve. 4.11 Where practicable, fusible plugs shall be externally marked to indicate the temperature at which they are designed to operate. 5 Relief pressure Where the pressure relief device is a bursting disc fit

35、ted to the valve of a seamless or welded container, the maximum bursting pressure shall not exceed the test pressure of the container. Container valves are designed to operate between 20 C and + 60 C and relief devices shall therefore be specified to operate within this temperature range. For contai

36、ners used in carbon dioxide service, the minimum burst pressure shall be no less than 180 bar g. 6 Bursting disc test A number of bursting discs shall be subjected to a burst test in accordance with BS 2915:1990 to check that disc rupture occurs within its prescribed range (see Clause 5). The number

37、 of bursting discs to undergo this test shall be subject to agreement between purchaser and manufacturer. NOTE These burst tests should be carried out with the disc in the valve body. 7 Installation and application of pressure relief devices Valves to be fitted to containers filled with a toxic gas

38、shall not be fitted with a pressure relief device. The design and location of a pressure relief device shall be compatible with the intended duty. Containers of 3.5 l water capacity and above which are filled with CO 2for industrial purposes shall be fitted with pressure relief devices. Bursting dis

39、cs may be fitted to any container intended for the conveyance of non-toxic and non-flammable gases. Where pressure relief devices are fitted to dissolved acetylene containers, they shall have either one or more fusible plugs set to operate at (100 2) C or other such pressure relief devices as approv

40、ed by the Health and Safety Executive. NOTE The Health and Safety Executive should be consulted if it is proposed to fit containers, other than dissolved acetylene containers, with fusible plugs.BS 341-4:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the indep

41、endent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that the

42、y possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the i

43、dentity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, inter

44、national and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to sup

45、ply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various

46、BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive subs

47、tantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be fou

48、nd at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyrigh

49、t, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designati