ASTM F442 F442M-2012 Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR&x2013 PR)《氯化聚氯乙烯 (CPVC) 塑料管 (SDR-PR) 的标准规范》.pdf

《ASTM F442 F442M-2012 Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR&x2013 PR)《氯化聚氯乙烯 (CPVC) 塑料管 (SDR-PR) 的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F442 F442M-2012 Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR&x2013 PR)《氯化聚氯乙烯 (CPVC) 塑料管 (SDR-PR) 的标准规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F442/F442M 09 F442/F442M 12 An American National StandardStandard Specification forChlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe(SDRPR)1This standard is issued under the fixed designation F442/F442M; the number immediately following the designation indicates the yearof original a

2、doption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.

3、1. Scope*1.1 This specification covers chlorinated poly(vinyl chloride) (CPVC) pipe made in standard thermoplastic pipe dimensionratios and pressure rated for water (see Appendix). Included are criteria for classifying CPVC plastic pipe materials and CPVCplastic pipe, and requirements and test metho

4、ds for materials, workmanship, dimensions, sustained pressure, burst pressure,flattening, and extrusion quality. Methods of marking are also given.NOTE 1The CPVC pipe covered by this specification was covered previously in Specification D2241.NOTE 2The sustained and burst pressure test requirements

5、and the pressure ratings in the Appendix are calculated from stress values obtained fromtests made on pipe 2 in. (50 mm) and smaller. However, tests on larger pipe have shown these stress values to be valid.1.2 The products covered by this specification are intended for use with the distribution of

6、pressurized liquids only, which arechemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems withcompressed air or other compressed gases some manufacturers do not allow pneumatic testing of their products. Consult withspecific product/co

7、mponent manufacturers for their specific testing procedures prior to pneumatic testing.NOTE 3Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious saftey hazards shoulda system fail for any reason.1.3 The text of this specification refere

8、nces notes, footnotes, and appendixes which provide explanatory material. These notesand footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standa

9、rd. The values stated in eachsystem may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems may result in non-conformance with the standard.Within the text, the SI units are shown in brackets.1.5 The following safety hazards

10、 caveat pertains only to the test methods portion, Section 8, of this specification:This standarddoes not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practices and dete

11、rmine the applicability of regulatory limitations prior touse.A specific precautionary statement is given in Note 6.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal PressureD159

12、9 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and FittingsD1600 Terminology for Abbreviated Terms Relating to PlasticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)CompoundsD2122 Test Method for

13、Determining Dimensions of Thermoplastic Pipe and FittingsD2241 Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)1 This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.25 on Vinyl

14、BasedPipe.Current edition approved Aug. 1, 2009May 1, 2012. Published August 2009August 2012. Originally approved in 1974. Last previous edition approved in 20052009 asF442 99 (2005)F4421 . 09. DOI: 10.1520/F0442_F0442M-09.10.1520/F0442_F0442M-12.2 For referenced ASTM standards, visit the ASTM websi

15、te, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indicatio

16、n of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be consid

17、ered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or P

18、ressure Design Basis forThermoplastic Pipe ProductsF412 Terminology Relating to Plastic Piping Systems2.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)32.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage32.4 NSF Standards:Standard No. 14 for Plastic Piping C

19、omponents and Related Materials4Standard No. 61 for Drinking Water Systems ComponentsHealth Effects43. Terminology3.1 DefinitionsDefinitions are in accordance with Terminology F412, and abbreviations are in accordance with TerminologyD1600, unless otherwise specified. The abbreviation for chlorinate

20、d poly(vinyl chloride) plastic is CPVC.3.2 Definitions of Terms Specific to This Standard:3.2.1 hydrostatic design stress the estimated maximum tensile stress the material is capable of withstanding continuously witha high degree of certainty that failure of the pipe will not occur. This stress is c

21、ircumferential when internal hydrostatic waterpressure is applied.3.2.2 pressure rating (PR)the estimated maximum water pressure the pipe is capable of withstanding continuously with ahigh degree of certainty that failure of the pipe will not occur.3.2.3 relation between standard dimension ratio, hy

22、drostatic design stress, and pressure ratingthe following expression,commonly known as the ISO equation,5 is used in this specification to relate standard dimension ratio, hydrostatic design stress,and pressure rating:2 S/P 5 R 21or 2 S/P 5 D o /t! 21where:S = hydrostatic design stress, psi MPa,P =

23、pressure rating, psi kPa,D o = average outside diameter, in. mmt = minimum wall thickness, in. mm, andR = standard thermoplastic pipe dimension ratio (Do /t for CPVC pipe), also known as SDR.3.2.4 standard thermoplastic pipe dimension ratio (SDR)the standard thermoplastic pipe dimension ratio (SDR)

24、is the ratioof pipe diameter to wall thickness. For CPVC pipe it is calculated by dividing the average outside diameter of the pipe inmillimetres or in inches by the minimum wall thickness in millimetres or in inches. If the wall thickness calculated by this formulais less than 0.060 in. 1.52 mm, it

25、 shall be arbitrarily increased to 0.060 in. 1.52 mm. The SDR values shall be rounded to thenearest 0.5.3.2.5 standard thermoplastic pipe materials designation codethe pipe materials designation code shall consist of theabbreviation CPVC for the type of plastic, followed by the ASTM type and grade i

26、n Arabic numerals and the design stress in unitsof 100 psi 690 kPa with any decimal figures dropped. When the design stress code contains less than two figures, a cipher shallbe used before the number. Thus a complete material code shall consist of four letters and four figures for CPVC plastic pipe

27、materials (see Section 5 and X1.2.1).4. Classification4.1 GeneralThis specification covers CPVC pipe made from one CPVC plastic pipe material in six standard dimension ratiosand water pressure ratings for nonthreaded pipe.4.2 Standard Thermoplastic Pipe Dimension Ratios (SDR)This specification cover

28、s CPVC pipe in six standard dimensionratios, namely, 11, 13.5, 17, 21, 26, and 32.5, which are uniform for all nominal pipe sizes for each material and pressure rating.These are referred to as SDR11, SDR13.5, SDR21, SDR17, SDR26, and SDR32.5, respectively. The pressure rating is uniformfor all nomin

29、al pipe sizes for a given CPVC pipe material and SDR (see Table X1.1).4.3 Hydrostatic Design StressesThis specification covers CPVC pipe made from CPVC plastic as defined by hydrostaticdesign stresses developed on the basis of long-term tests (see Appendix).NOTE 4This standard specification does not

30、 include requirements for pipe and fittings intended to be used to vent combustion gases.3 Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.4 Available from NSF International, P.O. Box 130140, 78

31、9 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http:/www.nsf.org.5 See ISO R161-1960: Pipes of Plastics Materials for the Transport of Fluids (Outside Diameters and Nominal Pressures) Part 1, Metric Series.F442/F442M 1225. Materials5.1 GeneralChlorinated poly(vinyl chloride) plastics used to make pipe

32、meeting the requirements of this specification arecategorized by means of two criteria, namely, (1) short-term strength tests, and (2) long-term hydrostatic strength tests at both 73and 180 F 23 and 82 C.5.2 Basic MaterialsThis specification covers CPVC pipe made from compounds meeting the requireme

33、nts of Class 23447 asdefined in Specification D1784. The materials shall have an established HDS (Hydrostatic Design Stress) equal to or greater than2000 psi 13.80 MPa at 73 F 23 C and 500 psi 3.45 MPa) at 180 F 82 C when evaluated in accordance with Test MethodD2837.5.3 Rework MaterialThe manufactu

34、rers shall use only their own clean rework pipe material and the pipe produced shall meetall the requirements of this specification.6. Requirements6.1 Dimension and Tolerances:6.1.1 Outside DiametersThe outside diameters and tolerances shall be as shown in Table 1 when measured in accordance withTes

35、t Method D2122. The tolerances on out-of-roundness shall apply only to pipe prior to shipment.6.1.2 Wall ThicknessThe wall thicknesses and tolerances shall be as shown in Table 2 when measured in accordance with TestMethod D2122.6.1.3 Wall Thickness RangeThe wall thickness range shall be within 12 %

36、 when measured in accordance with Test MethodD2122.6.2 Sustained PressureThe pipe shall not fail, balloon, burst, or weep as defined in Test Method D1598 at the test pressuresgiven in Table 3 when tested in accordance with 8.4.6.2.1 Accelerated Regression TestAt the option of the manufacturer, the a

37、ccelerated regression test may be used as asubstitute for both pressure testssustained and burst. The test shall be conducted in accordance with 8.4.1. The pipe shalldemonstrate a hydrostatic design basis projection at the 100 000-h intercept that meets the hydrostatic design basis categoryrequireme

38、nt (see Table 1, Test Method D2837) for the CPVC material used in its manufacture. If the lower confidence value at100 000 h differs from the extrapolated LTHS value by more than 15 % of the latter; or M in Appendix X2 (Test Method D2837)is zero or negative; or b in the equation h = a + bf in Append

39、ix X1 (Test Method D2837) is positive, consider the data unsuitable.6.3 Burst PressureThe minimum burst pressures for CPVC plastic pipe shall be as given in Table 4, when determined inaccordance with 8.5.6.4 FlatteningThere shall be no evidence of splitting, cracking, or breaking when the pipe is te

40、sted in accordance with 8.6.TABLE 1 Outside Diameters and Tolerances for CPVC Plastic PipeNominal Pipe SizeAverage OutsideDiameter,in. mmTolerances, in. mmFor AverageMaximum Out-of-Roundness(maximum minus minimum diameter)SDR32.5SDR26SDR21SDR17SDR13.5SDR1114 8 0.540 13.7 0.004 0.10 0.030 (0.76) 0.01

41、6 (0.41)38 10 0.675 17.1 0.004 0.10 0.030 (0.76) 0.016 (0.41)12 15 0.840 21.3 0.004 0.10 0.030 (0.76) 0.016 (0.41)34 20 1.050 26.7 0.004 0.10 0.030 (0.76) 0.020 (0.51)1 25 1.315 33.4 0.005 0.13 0.030 (0.76) 0.020 (0.51)114 32 1.660 42.2 0.005 0.13 0.030 (0.76) 0.024 (0.61)112 40 1.900 48.2 0.006 0.1

42、5 0.060 (1.52) 0.024 (0.61)2 50 2.375 60.3 0.006 0.15 0.060 (1.52) 0.024 (0.61)212 65 2.875 73.0 0.007 0.18 0.060 (1.52) 0.030 (0.76)3 80 3.500 88.9 0.008 0.20 0.060 (1.52) 0.030 (0.76)3 80 3.500 88.9 0.007 0.18 0.060 (1.52) 0.023 (0.58)312 90 4.000 101.6 0.008 0.20 0.100 (2.54) 0.030 (0.76)4 100 4.

43、500 114.3 0.009 0.23 0.100 (2.54) 0.030 (0.76)4 100 4.500 114.3 0.008 0.20 0.100 (2.54) 0.023 (0.58)5 125 5.563 141.3 0.010 0.25 0.100 (2.54) 0.060 (1.52)6 150 6.625 168.3 0.011 0.28 0.100 (2.54) 0.070 (1.78)8 200 8.625 219.1 0.015 0.38 0.150 (3.81) 0.090 (2.29)10 250 10.750 273.1 0.015 0.38 0.150 (

44、3.81) 0.100 (2.54)12 300 12.750 323.9 0.015 0.38 0.150 (3.81) 0.120 (3.05)F442/F442M 123TABLE 2 Wall Thicknesses and Tolerances for CPVC Plastic PipeNominalPipeSize,Wall ThicknessA,B in. mmSDR32.5 SDS26 SDR21 SDR17 SDR13.5 SDR11Min Tolerance Min Tolerance Min Tolerance Min Tolerance Min Tolerance Mi

45、n Tolerance14 8 . . . . . . . . . . . . . . . . . . . . . 0.060 1.52 +0.020 0.51 0.060 1.52 +0.020 0.5138 10 . . . . . . . . . . . . . . . . . . . . . . . . 0.060 1.52 +0.020 0.51 0.061 1.55 +0.020 0.5112 15 . . . . . . . . . . . . . . . . . . . . . . . . 0.062 1.57 +0.020 0.51 0.076 1.93 +0.020 0.5

46、134 20 . . . . . . . . . . . . 0.060 1.52 +0.020 0.51 0.062 1.57 +0.020 0.51 0.078 1.98 +0.020 0.51 0.095 2.41 +0.020 0.511 25 . . . . . . 0.060 1.52 +0.020 0.51 0.063 1.60 +0.020 0.51 0.077 1.96 +0.020 0.51 0.097 2.46 +0.020 0.51 0.119 3.02 +0.020 0.51114 32 . . . . . . 0.064 1.63 +0.020 0.51 0.079

47、 2.01 +0.020 0.51 0.098 2.49 +0.020 0.51 0.123 3.12 +0.020 0.51 0.151 3.84 +0.020 0.51112 40 . . . . . . 0.073 1.85 +0.020 0.51 0.090 2.29 +0.020 0.51 0.112 2.84 +0.020 0.51 0.141 3.58 +0.020 0.51 0.173 4.39 +0.021 0.532 50 . . . . . . 0.091 2.31 +0.020 0.51 0.113 2.87 +0.020 0.51 0.140 3.56 +0.020

48、0.51 0.176 4.47 +0.021 0.53 0.216 5.49 +0.026 0.66212 65 . . . . . . 0.110 2.79 +0.020 0.51 0.137 3.48 +0.020 0.51 0.169 4.29 +0.020 0.51 0.213 5.41 +0.026 0.66 0.261 6.63 +0.031 0.793 80 0.108 2.74 +0.020 0.51 0.135 3.43 +0.020 0.51 0.167 4.24 +0.020 0.51 0.206 5.23 +0.025 0.64 0.259 6.58 +0.031 0.79 0.318 8.08 +0.039 0.99312 90 0.123 3.12 +0.020 0.51 0.154 3.91 +0.020 0.51 0.190 4.83 +0.023 0.58 0.235 5.97 +0.028 0.71 0.296 7.52 +0.036 0.91 0.363 9.22 +0.0