ASTM F1333-1991(2013) Standard Specification for Construction of Fire and Foam Station Cabinets《消防和泡沫灭火站操纵室结构的标准规范》.pdf

《ASTM F1333-1991(2013) Standard Specification for Construction of Fire and Foam Station Cabinets《消防和泡沫灭火站操纵室结构的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1333-1991(2013) Standard Specification for Construction of Fire and Foam Station Cabinets《消防和泡沫灭火站操纵室结构的标准规范》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1333 91 (Reapproved 2013) An American National StandardStandard Specification forConstruction of Fire and Foam Station Cabinets1This standard is issued under the fixed designation F1333; the number immediately following the designation indicates the year oforiginal adoption or, in the

2、case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification provides design and constructioncriteria for double and single fire a

3、nd foam station cabinets.See Fig. 1 and Fig. 2. Valves, hose, and fittings are notincluded.1.2 Optional back and legs may be provided.1.3 The values stated in inch-pound units are to be regardedas the standard. The values in parentheses are for informationonly.2. Referenced Documents2.1 ASTM Standar

4、ds:2A36/A36M Specification for Carbon Structural SteelA53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and SeamlessA167 Specification for Stainless and Heat-ResistingChromium-Nickel Steel Plate, Sheet, and StripA312/A312M Specification for Seamless, Welded, andHeavil

5、y Cold Worked Austenitic Stainless Steel PipesA569/A569M Specification for Steel, Carbon (0.15Maximum, Percent), Hot-Rolled Sheet and Strip Commer-cial (Withdrawn 2000)3B209 Specification for Aluminum and Aluminum-AlloySheet and PlateB221 Specification for Aluminum and Aluminum-Alloy Ex-truded Bars,

6、 Rods, Wire, Profiles, and TubesF593 Specification for Stainless Steel Bolts, Hex CapScrews, and StudsF594 Specification for Stainless Steel NutsF783 Specification for Staple, Handgrab, Handle, and Stir-rup Rung2.2 American National Standards:4ANSI B18.21.1 Lock WasherANSI B18.22.1 Plain Washer2.3 O

7、ther Standards:American Bureau of Shipping Rules for Building andClassing of Steel Vessels5American Welding Society Publication, AWS D 1.1 Struc-tural Welding Code63. Classification3.1 Type I, Single Cabinet (see Fig. 1 and Figs. 3-9):3.1.1 Grade 1Right-hand door active leaf.3.1.1.1 Class A, Mild St

8、eelSpecification A36/A36M.3.1.1.2 Class B, Stainless SteelSpecification A167.3.1.1.3 Class C, AluminumSpecification B209.3.1.2 Grade 2Left-hand door.3.1.2.1 Class A, Mild SteelSpecification A36/A36M.3.1.2.2 Class B, Stainless SteelSpecification A167.3.1.2.3 Class C, AluminumSpecification B209.3.2 Ty

9、pe II, Double Cabinet (see Fig. 2 and Fig. 8):3.2.1 Grade 1Right-hand doors active leaf.3.2.1.1 Class A, Mild SteelSpecification A36/A36M.3.2.1.2 Class B, Stainless SteelSpecification A167.3.2.1.3 Class C, AluminumSpecification B209.4. Ordering Information4.1 Fire and foam cabinets ordered in accord

10、ance with thisspecification shall include the following:4.1.1 ASTM title, designation, and year of issue,4.1.2 Quantity (number of cabinets),4.1.3 Type, grade, and class, and4.1.4 Optional features.5. Materials and Manufacture5.1 Materials:5.1.1 See Table 1.5.1.2 Class materials.1This specification

11、is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved Oct. 1, 2013. Published October 2013. Originallyapproved in 1991. Last previous edition approved in 2007 as F1

12、333 - 91(2007).DOI: 10.1520/F1333-91R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved ve

13、rsion of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.5Available from American Bureau of Shipping (ABS), ABS Plaza, 16855Northchase Dr., Houston, TX 77060, http:/ww

14、w.eagle.org.6Available from American Welding Society (AWS), 550 NW LeJeune Rd.,Miami, FL 33126, http:/www.aws.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.2.1 All materials for Class A cabinets shall meet therequirements of

15、 Specifications A53/A53M and A36/A36M orSpecification A569/A569M, except as specified in Table 1.5.1.2.2 All materials for Class B cabinets shall meet therequirements of Specifications A167 and A312/A312M, exceptas specified in Table 1.5.1.2.3 All materials for Class C cabinets shall meet therequire

16、ments of Specifications B209 and B221 except asspecified in Table 1.5.2 Manufacture:5.2.1 Welding shall be in accordance with the AmericanBureau of Shipping Rules for Building and Classing of Vesselsor American Welding Society Structural Welding Code AWSD1.1.5.2.2 Punchout shall have a 3-in. (approx

17、imately 76-mm)diameter hole with three evenly spaced116-in. (approximately1.5-mm) tabs for both sides of cabinet (see Fig. 3).6. Workmanship, Finish, and Appearance6.1 Fire and foam cabinets shall be free of weld spatter,burrs, and sharp corners, rough edges, and other defects whichmight be hazardou

18、s to personnel and equipment.6.2 Surface Requirements:6.2.1 Class A CabinetsCoat with 1.0-mil dry filmthickness, inorganic zinc silicate, including options.6.2.2 Class B CabinetsUncoated. Optional legs coatedwith 1.0-mil dry film thickness, inorganic zinc silicate.6.2.3 Class C CabinetsUncoated.NOTE

19、 11 in. = 25.4 mm.FIG. 1 Fire and Foam CabinetType IFIG. 2 Fire and Foam CabinetType IITABLE 1 Parts ListItem NumberADescriptionB1 Frame plate, 12 gage2 Hinge pad flatbar, 112 in. by 412 in. by 12 gage3 Hinge undrilled butt, 4 in. long by 2 in. wide, commercialstainless steel4 Brace angle,34 by34 by

20、18 in.5 Door plate, 12 gage6 Staple round bar,38-in. dimensions in accordance withSpecification F7837 Hook round bar,14 in.8 Latch flat bar,316 by1in.9 Keeper flat bar,31 by1in.10 Rivet button monel or aluminum,14 in.11 Clip wrench/nozzle, plate 12 gage12 Snubber rubber, commercial13 Retainer plate,

21、 12 gage14 Saddle pipe 6 NPS Schedule 40, Specification A53/A53M15 Strap hose securing, quick disconnect, commercial16 Clip hook securing, commercial, Specification A16717 Washer TFE-fluorocarbonOptions18 Back plate,316 in.19 Leg angle, 4 by 3 by38 in., Specification A36/A36M20 Brace angle, 4 by 3 b

22、y38 in., Specification A36/A36M21 Bolt hex head,38 16 UNC2A by 114-in. long,stainless steel Type 316, Specification F59322 Washer flat, stainless steel Type 316 for38-in. diameter bolt,ANSI B18.22.1, Type B23 Nut heavy hex38 16 UNC2B, stainless steel Type316, Specification F59424 Washer lock, stainl

23、ess steel Type 316 for38-in. diameterbolt, ANSI B18.21.1A36/A36M, RegularType II Double Cabinet Only25 Back bar flat bar, 112 in. by 30 in. by 12 gageAItems 18 to 24 (inclusive) are optional.B1 in. = 25.4 mm.F1333 91 (2013)27. Packaging and Package Marking7.1 Loose fasteners and hardware shall be pa

24、ckaged andsecurely attached inside each cabinet.7.2 ShippingEach cabinet shall bear a weathertight tagshowing the purchase order number, ASTM standarddesignation, type, and name of manufacturer.7.3 The cabinets shall be crated or attached to a pallet in amanner acceptable for shipment by commercial

25、carrier. Thecabinets shall be crated individually.8. Keywords8.1 fire; foam; foam station cabinet; marine technology;shipsFIG. 3 Section “B-B”FIG. 4 Section “C-C”FIG. 5 Wrench/Nozzle Clip Detail “A”FIG. 6 Latch Assembly, Type II, Grade 1 Cabinet Shown, OthersSimilar, Detail “B”F1333 91 (2013)3FIG. 7

26、 Hook Assembly Detail “C”FIG. 8 Hose Rack Detail “D”F1333 91 (2013)4ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any

27、 such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are in

28、vited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not receive

29、d a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of t

30、his standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).FIG. 9 Front View of Back Leg and Back Option Detail “E”F1333 91 (2013)5