ASTM D5172-1991(2004) Standard Guide for Documenting the Standard Operating Procedures Used for the Analysis of Water《为水质分析操作程序提供资料》.pdf

《ASTM D5172-1991(2004) Standard Guide for Documenting the Standard Operating Procedures Used for the Analysis of Water《为水质分析操作程序提供资料》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5172-1991(2004) Standard Guide for Documenting the Standard Operating Procedures Used for the Analysis of Water《为水质分析操作程序提供资料》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 5172 91 (Reapproved 2004)Standard Guide forDocumenting the Standard Operating Procedures Used forthe Analysis of Water1This standard is issued under the fixed designation D 5172; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide addresses the need for each laboratoryengaged in the analysis of water and wastewat

3、er to develop andmaintain an up-to-date written manual that clearly and com-pletely delineates the exact steps followed in performing everytest method and procedure used in the laboratory, that is, amanual of their standard operating procedures (SOPs).1.2 This guide details the practices necessary t

4、o provideclear in-house SOPs and a mechanism whereby the normaldevelopment and evolution of an analytical test method orprocedure can be controlled and properly evaluated for incor-poration into the SOP used in that laboratory.1.3 This standard does not purport to address all of thesafety concerns,

5、if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. Specific precau-tionary statements are given in the note.2. Referenced Documents2.1 AST

6、M Standards:2D 1129 Terminology Relating to Water3. Terminology3.1 DefinitionsFor definitions of terms used in this guide,refer to Terminology D 1129.3.2 Definitions of Terms Specific to This Standard:3.2.1 procedure any process involving sequential stepsconducted to achieve a specific objective.4.

7、Summary of Guide4.1 This guide describes suggested practices for developingand maintaining a current compilation of the complete andexact analytical test methods and procedures being used in aparticular laboratory.5. Significance and Use5.1 The exact analytical test methods and procedures usedin any

8、 laboratory may be unique and affect the usability of theiranalytical results. A general reference to a book of standardanalytical test methods, guides, and practices published by areputable organization such as ASTM is not sufficient toguarantee acceptable results. As a point of clarification, apro

9、cedure may be part of a test method or it may be any otherroutine process the laboratory personnel must follow, forexample, glassware cleaning, quality control, routine mainte-nance, or data reporting procedures.5.2 A significant part of the variability of results generatedby different laboratories

10、analyzing the same samples and citingthe same general reference is due to differences in the way theanalytical test methods and procedures are actually performedin each laboratory. These differences are often caused by theslight changes or adjustments allowed by the general reference,but that can af

11、fect the final results.5.3 The manual of SOPs is an important component of anylaboratorys quality assurance program. As with all qualityassurance activities, the importance of this manual lies in itsimpact on maintaining uniformity of test method performanceand the utility of data generated by the l

12、aboratory.5.4 Each laboratory should develop and maintain a loose-leaf manual containing an exact step-by-step description ofhow every test method and procedure is performed in thelaboratory to help guarantee uniform performance amongdifferent analysts using them.5.5 With adequate documentation of a

13、 laboratorys com-plete and exact analytical test methods and procedures, alaboratory will have improved confidence in its ability toreproduce analytical conditions exactly and thereby generalreproducible results. This manual of SOPs is the cornerstone ofa laboratorys creditability.6. Suggested Steps

14、 for Generating a Manual of SOPs6.1 The manual should begin with specification of thepublished references from a standard-setting organization orregulatory agency. An adequate written SOP should then bedrafted in-house for each test method or procedure performedby the laboratory. A standard format s

15、hould be used that isappropriate to the SOP and is similar in scope to the formatsincluded in this guide as Annex A1 and Annex A2. All aspects1This guide is under the jurisdiction of ASTM Committee D19 on Water and isthe direct responsibility of Subcommittee D19.02 on General Specifications,Technica

16、l Resources, and Statistical Methods.Current edition approved Sept. 19, 1991. Published February 1992.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards

17、Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.of the test method or procedure as actually applied in thelaboratory should be addressed in detail.NOTE 1Caution: When a laboratory is performin

18、g an analyticalprocedure in a regulatory or legal environment, it is of vital importancethat the in-house version be maintained within the technical allowances ofthe mandated procedure. Technical departures from the mandated proce-dure may result in a legal liability. One way to demonstrate consiste

19、ncywith the mandated procedure is to copy the standard procedure aspublished and add footnotes to fully document the specific in-houseversion.6.2 The basic structure and elements of a test method aretypically present in consensus standards published by groupssuch as ASTM. But, invariably, these publ

20、ished test methodsand procedures must be interpreted for application in eachlaboratory. Published versions of other test methods andprocedures are often very general or completely unavailable.6.3 In generating a draft SOP, it is often helpful to solicitinput from analysts experienced with a test met

21、hod or proce-dure who are familiar with its vagaries and pitfalls, and canprovide valuable assistance in writing a complete and exactdocument on how the procedure is done in the laboratory. It isoften useful to have all of the analytical staff review the finaldraft.6.4 After an initial draft to iden

22、tify the pertinent details ofan SOP, the laboratory should conduct a study to verify itsapplicability to the sample matrices encountered in that par-ticular laboratory. In addition, the laboratory should verify thatit can, at a minimum, obtain results with precision and biasequivalent to those in pu

23、blished references (if available forsimilar matrices). The precision and bias obtained in the studyshould be recorded for future use relating to evaluation ofquality control (QC) data from the sample matrices studied.6.4.1 This process of verifying the utility of an SOP forgiven sample types is call

24、ed “method validation” and eachlaboratory needs an SOP detailing how this process is done inthat laboratory. It is a process that should be performedwhenever a new SOP is first put into practice or whenever anSOP is to be modified or used on new sample matrices.6.5 When the test method involves the

25、selection of variousoptions depending on the sample matrix, it should be organizedinto subsections dealing with each of the optional paths. Eachoptional approach should be treated as a separate SOP. Mecha-nisms should be established whereby the exact proceduresemployed to generate a result can be id

26、entified at a later time.In cases where subsections of a test method for a single analytereflect substantially different chemical bases, a completelyseparate SOP should be generated from each of these subsec-tions.6.6 The final version should be annotated with an effectivedate, revision number, page

27、 numbers out of total number ofpages, and the author(s). The effective date is the date when itwas first used to produce actual data. The final version and allsubsequent revisions should be approved and signed by thelaboratory manager and the quality assurance officer or theirdesignees, and distribu

28、ted to all analysts for bench use.7. Centralized Files7.1 A master copy of the laboratorys SOPs should be kepton-file under the control of the quality assurance officer.Whenever a procedure is modified, the revised version shouldbe documented and the changes highlighted. Copies of therevised SOP sho

29、uld be distributed to the staff to replace theprevious version, that they should destroy, and a new effectivedate for the revision and a revised copy of the SOP should beadded to the master file along with an explanation of why therevision was necessary. Out-of-date versions of an SOP shouldbe filed

30、 separately by the QA officer for future reference.Through use of such an updating mechanism, the laboratorywill be able to identify the exact procedure being followed atthe time a particular result was generated.8. Suggested Use and Maintenance8.1 While performing an SOP, the analyst should have ac

31、opy of the current documentation readily at-hand and followit to the letter. If the SOP allows for multiple options, theoption employed should be noted with the final results.8.2 When an analyst encounters a situation for which noclear direction is provided in the SOP, possible changes shouldbe disc

32、ussed with a qualified supervisor, and approved anddocumented before use.8.3 Records should be maintained of the distribution of thelaboratorys SOPs and their revisions.9. Procedure Audits9.1 For a variety of reasons, procedures as they are actuallyapplied in the laboratory have a tendency to drift

33、away from theapproved written versions. For this reason, the actual perfor-mance of each analyst while performing a test method orprocedure should be audited by the responsible supervisor orthe quality assurance officer, or both, on a periodic basis,ideally not less than once per year and more frequ

34、ently duringanalysts initial training period. Any deviations from thewritten SOP should be noted and evaluated. The analystsperformance should be corrected or the SOP should be modi-fied to incorporate the deviations. When the deviations aredeemed to be inappropriate, the SOP should be annotated tos

35、pecifically exclude the noted deviation.10. Responsibility for Improvement10.1 Analytical methods and procedures are not static,finished products; they are continually modified in response tochanging demands or to improve performance or efficiency.Every laboratory should emphasize the responsibility

36、 of itsprofessional staff to monitor pertinent scientific publicationsfor new developments relevant to the SOPs under theirjurisdiction.11. Keywords11.1 analysis; documenting; procedure; standard operatingprocedureD 5172 91 (2004)2ANNEXES(Mandatory Information)A1. SUGGESTED FORMAT FOR A TEST METHOD

37、SOPA1.1 Record of Approval and UpdateInclude the follow-ing information:Approvals: Laboratory Manager_ Date _QA Officer _ Date _Revision No. _ by _ Effective Date _Total Pages _ Pages Revised _A1.2 TitleThe property, analyte, or class of compoundsbeing measured. It is also useful to include any labo

38、ratorycodes used to refer to this test method.A1.3 Principal Reference(s)Apublished reference(s) thatdefines the basic analytical method.A1.4 Scope of ApplicationTypes of sample matrices andthe analytical range to which this test method can be applied.A1.5 Summary of Test MethodA short description h

39、igh-lighting the definitive chemical and procedural elements of thetest method.A1.6 InterferencesA general overview of the kinds ofmatrices that cause unacceptable performance and the generalmechanisms for compensating for them. The specific steps fordealing with interferences should be incorporated

40、 in theprocedure portion of the test method as options defining aunique method.A1.7 Sample HandlingItemize any concerns relating toproper handling of samples after they are received for analysis.Specifically indicate holding times, storage procedures, andpreservation procedure (applied at or prior t

41、o receipt).A1.8 Apparatus:A1.8.1 InstrumentsSpecify model and make.A1.8.2 LabwareSpecify preparation and conditioning,class, assembly instructions, diagrams, etc.A1.9 Chemicals and ReagentsA listing of requiredchemicals, purity grade; instructions for reagent makeup;standardizing, storing, and dispo

42、sing of reagents; reagent andchemical shelf life.A1.10 SafetyIdentify at each point in the test methodwhere safety precautions are to be observed; reference thissection or a safety manual.A1.11 ProcedureA detailed description of each stepconsidered essential to the reproducibility and accuracy of th

43、etest method as actually carried out in the laboratory. Includecalibration procedures. Re-analysis sample preparation stepsshould be specified.A1.12 Short Hand ProcedureA condensed version of thetest method that can be used for quick reference.A1.13 CalculationA description of the mathematicalsteps

44、required to complete the analysis. Include sample calcu-lations and the number of significant figures to report. It is alsohelpful to include a sample of the analytical bench form.A1.14 Data ManagementSpecific instructions on howand where data should be reported, and on what, how, andwhere data shou

45、ld be stored.A1.15 Quality Assurance and Quality Control:A1.15.1 Itemize desirable and mandatory quality assuranceprocedures specific to this test method, especially equipmentand reagent checks, recalibrations, and other system checksthat should be done routinely. This section should be refer-enced

46、in the procedure section (see A1.11).A1.15.2 Specify statistical quality control parameters: batchsize, reference materials, frequencies, data handling. Thisshould also be referenced in the procedure section (see A1.11).A1.15.3 Lowest Reporting LevelThe concentration belowwhich all results are repor

47、ted as “less than,” based on thespecified procedure and sample size. The laboratory shouldadopt a uniform system for determining this limit.A1.15.4 Precision and Bias StatementsA tabulation ofthese statistics as determined using this test method in yourlaboratory, by matrix and concentration level.A

48、1.16 ReferencesA listing of published documents sup-porting the specifics of this test method.A1.17 AppendixesCopies of documents, tables, or graphsthat would be useful to have appended to the test method.D 5172 91 (2004)3A2. SUGGESTED FORMAT FOR A NON-TEST METHOD SOPA2.1 Record of Approval and Upda

49、teInclude the follow-ing information:Approvals: Laboratory Manager_ Date _QA Officer _ Date _Revision No. _ by _ Effective Date _Total Pages _ Pages Revised _A2.2 TitleShould be descriptive of the SOP.A2.3 Summary of the SOPShould include a statement ofits purpose.A2.4 ApparatusProvide description.A2.5 SafetyDiscuss any hazards and how they may beminimize