ASTM D790-2015e2 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials《未增强和增强塑料与电气绝缘材料的弯曲性能的标准试验方法》.pdf

《ASTM D790-2015e2 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials《未增强和增强塑料与电气绝缘材料的弯曲性能的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D790-2015e2 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials《未增强和增强塑料与电气绝缘材料的弯曲性能的标准试验方法》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D790 152Standard Test Methods forFlexural Properties of Unreinforced and Reinforced Plasticsand Electrical Insulating Materials1This standard is issued under the fixed designation D790; the number immediately following the designation indicates the year oforiginal adoption or, in the ca

2、se of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1NOTEEditorially

3、 corrected 4.3 in January 2016.2NOTEEditorial corrections were made in February 2016.1. Scope*1.1 These test methods are used to determine the flexuralproperties of unreinforced and reinforced plastics, includinghigh modulus composites and electrical insulating materialsutilizing a three-point loadi

4、ng system to apply a load to asimply supported beam (specimen). The method is generallyapplicable to both rigid and semi-rigid materials, but flexuralstrength cannot be determined for those materials that do notbreak or yield in the outer surface of the test specimen withinthe 5.0 % strain limit.1.2

5、 Test specimens of rectangular cross section are injectionmolded or, cut from molded or extruded sheets or plates, or cutfrom molded or extruded shapes. Specimens must be solid anduniformly rectangular. The specimen rests on two supports andis loaded by means of a loading nose midway between thesupp

6、orts.1.3 Measure deflection in one of two ways; using crossheadposition or a deflectometer. Please note that studies have shownthat deflection data obtained with a deflectometer will differfrom data obtained using crosshead position. The method ofdeflection measurement shall be reported.NOTE 1Requir

7、ements for quality control in production environmentsare usually met by measuring deflection using crosshead position.However, more accurate measurement may be obtained by using andeflection indicator such as a deflectometer.NOTE 2Materials that do not rupture by the maximum strain allowedunder this

8、 test method may be more suited to a 4-point bend test. The basicdifference between the two test methods is in the location of the maximumbending moment and maximum axial fiber stresses. The maximum axialfiber stresses occur on a line under the loading nose in 3-point bending andover the area betwee

9、n the loading noses in 4-point bending. A four-pointloading system method can be found in Test Method D6272.1.4 The values stated in SI units are to be regarded as thestandard. The values provided in parentheses are for informa-tion only.1.5 The text of this standard references notes and footnotesth

10、at provide explanatory material. These notes and footnotes(excluding those in tables and figures) shall not be consideredas requirements of the standard.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of th

11、is standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE 3This standard and ISO 178 address the same subject matter,but differ in technical content.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Condi

12、tioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD883 Terminology Relating to PlasticsD4000 Classification System for Specifying Plastic Materi-alsD4101 Specification for Polypropylene Injection and Extru-sion MaterialsD5947 Test Methods for Physical Dimensions of Solid

13、Plastics SpecimensD6272 Test Method for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-als by Four-Point BendingE4 Practices for Force Verification of Testing MachinesE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Tes

14、t MethodE2309 Practices for Verification of Displacement Measuring1These test methods are under the jurisdiction of ASTM Committee D20 onPlastics and are the direct responsibility of Subcommittee D20.10 on MechanicalProperties.Current edition approved Dec. 1, 2015. Published January 2016. Originally

15、approved in 1970. Last previous edition approved in 2010 as D790 10. DOI:10.1520/D0790-15E02.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document

16、Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1Systems and Devices Used in Material Testing Machines2.2 ISO Standard:3ISO 178 PlasticsDe

17、termination of Flexural Properties3. Terminology3.1 DefinitionsDefinitions of terms applying to these testmethods appear in Terminology D883 and Annex A2 of TestMethod D638.4. Summary of Test Method4.1 Atest specimen of rectangular cross section rests on twosupports in a flat-wise position and is lo

18、aded by means of aloading nose located midway between the supports. Unlesstesting certain laminated materials (see 7 for guidance), asupport span-to-depth (of specimen) ratio 16:1 shall be used.The specimen is deflected until rupture occurs in the outersurface of the test specimen or until a maximum

19、 strain (see5.1.6) of 5.0 % is reached, whichever occurs first.4.2 Procedure A is designed principally for materials thatbreak at comparatively small deflections and it shall be used formeasurement of flexural properties, particularly flexuralmodulus, unless the material specification states otherwi

20、se.Procedure A employs a strain rate of 0.01 mm/mm/min (0.01in./in./min) and is the preferred procedure for this test method.4.3 Procedure B is designed principally for those materialsthat do not break or yield in the outer surface of the testspecimen within the 5.0 % strain limit when Procedure Aco

21、nditions are used. Procedure B employs a strain rate of 0.10mm/mm/min (0.10 in./in./min).4.4 Type I tests utilize crosshead position for deflectionmeasurement.4.5 Type II tests utilize an instrument (deflectometer) fordeflection measurement.4.6 The procedure used and test type shall be reportedNOTE

22、4Comparative tests may be run in accordance with eitherprocedure, provided that the procedure is found satisfactory for thematerial being tested. Tangent modulus data obtained by Procedure Atends to exhibit lower standard deviations than comparable resultsobtained by means of Procedure B.5. Signific

23、ance and Use5.1 Flexural properties as determined by this test method areespecially useful for quality control and specification purposes.They include:5.1.1 Flexural Stress (f)When a homogeneous elasticmaterial is tested in flexure as a simple beam supported at twopoints and loaded at the midpoint,

24、the maximum stress in theouter surface of the test specimen occurs at the midpoint.Flexural stress is calculated for any point on the load-deflectioncurve using equation (Eq 3) in Section 12 (see Notes 5 and 6).NOTE 5Eq 3 applies strictly to materials for which stress is linearlyproportional to stra

25、in up to the point of rupture and for which the strainsare small. Since this is not always the case, a slight error will beintroduced if Eq 3 is used to calculate stress for materials that are not trueHookean materials. The equation is valid for obtaining comparison dataand for specification purpose

26、s, but only up to a maximum fiber strain of5 % in the outer surface of the test specimen for specimens tested by theprocedures described herein.NOTE 6When testing highly orthotropic laminates, the maximumstress may not always occur in the outer surface of the test specimen.4Laminated beam theory mus

27、t be applied to determine the maximumtensile stress at failure. If Eq 3 is used to calculate stress, it will yield anapparent strength based on homogeneous beam theory. This apparentstrength is highly dependent on the ply-stacking sequence of highlyorthotropic laminates.5.1.2 Flexural Stress for Bea

28、ms Tested at Large SupportSpans (f)If support span-to-depth ratios greater than 16 to 1are used such that deflections in excess of 10 % of the supportspan occur, the stress in the outer surface of the specimen fora simple beam is reasonably approximated using equation (Eq4)in12.3 (see Note 7).NOTE 7

29、When large support span-to-depth ratios are used, significantend forces are developed at the support noses which will affect themoment in a simple supported beam. Eq 4 includes additional terms thatare an approximate correction factor for the influence of these end forcesin large support span-to-dep

30、th ratio beams where relatively large deflec-tions exist.5.1.3 Flexural Strength (fM)Maximum flexural stresssustained by the test specimen (see Note 6) during a bendingtest. It is calculated according to Eq 3 or Eq 4. Some materialsthat do not break at strains of up to 5 % give a load deflectioncurv

31、e that shows a point at which the load does not increasewith an increase in strain, that is, a yield point (Fig. 1, Curveb), Y. The flexural strength is calculated for these materials byletting P (in Eq 3 or Eq 4) equal this point, Y.5.1.4 Flexural Offset Yield StrengthOffset yield strength isthe st

32、ress at which the stress-strain curve deviates by a givenstrain (offset) from the tangent to the initial straight line portionof the stress-strain curve. The value of the offset must be givenwhenever this property is calculated.NOTE 8Flexural Offset Yield Strength may differ from flexuralstrength de

33、fined in 5.1.3. Both methods of calculation are described in theannex to Test Method D638.5.1.5 Flexural Stress at Break (fB)Flexural stress at breakof the test specimen during a bending test. It is calculatedaccording to Eq 3 or Eq 4. Some materials give a loaddeflection curve that shows a break po

34、int, B, without a yieldpoint (Fig. 1, Curve a) in which case fB= fM. Other materialsgive a yield deflection curve with both a yield and a breakpoint, B (Fig. 1, Curve b). The flexural stress at break iscalculated for these materials by letting P (in Eq 3 or Eq 4)equal this point, B.5.1.6 Stress at a

35、 Given StrainThe stress in the outersurface of a test specimen at a given strain is calculated inaccordance with Eq 3 or Eq 4 by letting P equal the load readfrom the load-deflection curve at the deflection correspondingto the desired strain (for highly orthotropic laminates, see Note6).3Available f

36、rom American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4For a discussion of these effects, see Zweben, C., Smith, W. S., and Wardle, M.W., “Test Methods for Fiber Tensile Strength, Composite Flexural Modulus andProperties of Fabric-Reinforc

37、ed Laminates,” Composite Materials: Testing andDesign (Fifth Conference), ASTM STP 674, 1979, pp. 228262.D790 15225.1.7 Flexural Strain, fNominal fractional change in thelength of an element of the outer surface of the test specimenat midspan, where the maximum strain occurs. Flexural strainis calcu

38、lated for any deflection using Eq 5 in 12.4.5.1.8 Modulus of Elasticity:5.1.8.1 Tangent Modulus of ElasticityThe tangent modu-lus of elasticity, often called the “modulus of elasticity,” is theratio, within the elastic limit, of stress to corresponding strain.It is calculated by drawing a tangent to

39、 the steepest initialstraight-line portion of the load-deflection curve and using Eq6 in 12.5.1 (for highly anisotropic composites, see Note 15).NOTE 9Shear deflections can seriously reduce the apparent modulusof highly anisotropic composites when they are tested at low span-to-depth ratios.4For thi

40、s reason, a span-to-depth ratio of 60 to 1 isrecommended for flexural modulus determinations on these composites.Flexural strength should be determined on a separate set of replicatespecimens at a lower span-to-depth ratio that induces tensile failure in theouter fibers of the beam along its lower f

41、ace. Since the flexural modulusof highly anisotropic laminates is a critical function of ply-stackingsequence, it will not necessarily correlate with tensile modulus, which isnot stacking-sequence dependent.5.1.8.2 Secant ModulusThe secant modulus is the ratio ofstress to corresponding strain at any

42、 selected point on thestress-strain curve, that is, the slope of the straight line thatjoins the origin and a selected point on the actual stress-straincurve. It shall be expressed in megapascals (pounds per squareinch). The selected point is chosen at a pre-specified stress orstrain in accordance w

43、ith the appropriate material specificationor by customer contract. It is calculated in accordance with Eq6 by letting m equal the slope of the secant to the load-deflection curve. The chosen stress or strain point used for thedetermination of the secant shall be reported.5.1.8.3 Chord Modulus (Ef)Th

44、e chord modulus is calcu-lated from two discrete points on the load deflection curve. Theselected points are to be chosen at two pre-specified stress orstrain points in accordance with the appropriate materialspecification or by customer contract. The chosen stress orstrain points used for the deter

45、mination of the chord modulusshall be reported. Calculate the chord modulus, Efusing Eq 7in 12.5.2.5.2 Experience has shown that flexural properties vary withspecimen depth, temperature, atmospheric conditions, andstrain rate as specified in Procedures A and B.5.3 Before proceeding with these test m

46、ethods, refer to theASTM specification of the material being tested. Any testspecimen preparation, conditioning, dimensions, or testingparameters, or combination thereof, covered in the ASTMmaterial specification shall take precedence over those men-tioned in these test methods. Table 1 in Classific

47、ation SystemD4000 lists the ASTM material specifications that currentlyexist for plastics.6. Apparatus6.1 Testing MachineA testing machine capable of beingoperated at constant rates of crosshead motion over the rangeindicated and comprised of the following:6.1.1 Load FrameThe stiffness of the testin

48、g machineshall be such that the total elastic deformation of the systemdoes not exceed 1 % of the total deflection of the test specimenduring testing, or appropriate corrections shall be made.6.1.1.1 Fixed MemberA fixed or essentially stationarymember holding the specimen supports;6.1.1.2 Movable Me

49、mberA movable member carrying theloading nose.6.1.2 Loading Noses and SupportsThe loading nose andsupports shall have cylindrical surfaces.6.1.2.1 The radii of the loading nose and supports shall be5.0 6 0.1 mm (0.197 6 0.004 in.) unless otherwise specified inan ASTM material specification or as agreed upon betweeninterested parties.6.1.2.2 Other Radii for Loading Noses and SupportsAlternative loading noses and supports are permitted to be usedin order to avoid excessive indentation or failure due to stressconcentration directly under the lo