ASTM C1063-2018b Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster.pdf
《ASTM C1063-2018b Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster.pdf》由会员分享,可在线阅读,更多相关《ASTM C1063-2018b Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster.pdf(11页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C1063 18bStandard Specification forInstallation of Lathing and Furring to Receive Interior andExterior Portland Cement-Based Plaster1This standard is issued under the fixed designation C1063; the number immediately following the designation indicates the year oforiginal adoption or, in
2、the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1
3、.1 This specification covers the minimum technical re-quirements for lathing and furring for the application ofexterior and interior portland cement-based plaster, as inSpecifications C841 or C926. These requirements do not bydefault define a unit of work or assign responsibility forcontractual purp
4、oses, which is the purview of a contract orcontracts made between contracting entities.1.2 Where a fire resistance rating is required for plasteredassemblies and constructions, details of construction shall be inaccordance with reports of fire tests of assemblies that havemet the requirements of the
5、 fire rating imposed.1.3 Where a specific degree of sound control is required forplastered assemblies and constructions, details of constructionshall be in accordance with official reports of tests conducted inrecognized testing laboratories in accordance with the appli-cable requirements of Test Me
6、thod E90.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This international standard was developed in accor-dance with internatio
7、nally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A653/A653M
8、 Specification for Steel Sheet, Zinc-Coated(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)by the Hot-Dip ProcessC11 Terminology Relating to Gypsum and Related BuildingMaterials and SystemsC841 Specification for Installation of Interior Lathing andFurringC847 Specification for Metal LathC926 Sp
9、ecification for Application of Portland Cement-Based PlasterC933 Specification for Welded Wire LathC1032 Specification for Woven Wire Plaster BaseC1280 Specification for Application of Exterior GypsumPanel Products for Use as SheathingC1861 Specification for Lathing and Furring Accessories,and Faste
10、ners, for Interior and Exterior Portland Cement-Based PlasterE90 Test Method for Laboratory Measurement of AirborneSound Transmission Loss of Building Partitions andElements2.2 US Department of Commerce (DOC) StandardsPS 1 Voluntary Product Standard PS 1, Structural PlywoodPS 2 Voluntary Product Sta
11、ndard PS 2, Performance Stan-dard for Wood-Based Structural Use Panels3. Terminology3.1 Definitions:3.1.1 For definitions relating to ceilings and walls, seeTerminology C11.3.1.2 For definitions relating to lathing accessories. furringaccessories and fasteners, see Specification C1861.3.2 Definition
12、s of Terms Specific to This Standard:3.2.1 building enclosure, nsystem of building assembliesand materials designed and installed in such a manner as toprovide a barrier between different environments.1This specification is under the jurisdiction of ASTM Committee C11 onGypsum and Related Building M
13、aterials and Systems and is the direct responsibilityof Subcommittee C11.03 on Specifications for theApplication of Gypsum and OtherProducts in Assemblies.Current edition approved June 1, 2018. Published July 2018. Originally approvedin 1986. Last previous edition approved in 2018 as C1063 18a. DOI:
14、 10.1520/C1063-18B.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at t
15、he end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for
16、theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.13.2.2 control joint, na joint that accommodates movementof plaster shrinkage and curing along predetermined, usuallystraight, lines.3.2.3 expansio
17、n joint, na joint that accommodates move-ment beyond plaster shrinkage and curing.NOTE 1For design consideration of control and expansion joints, seeAnnex A2.3.1.2 of Specification C926.3.2.4 framing member, nstuds, joist, runners (track),bridging, bracing, and related accessories manufactured orsup
18、plied in wood or light gauge steel.3.2.5 hangers, nwires or steel rods or straps used tosupport main runners for suspended ceilings beneath floor orroof constructions.3.2.6 inserts, ndevices embedded in concrete framingmembers to provide a loop or opening for attachment ofhangers.3.2.7 saddle tie, n
19、see Figs. 1 and 2.3.2.8 self-furring, adja metal plaster base manufacturedwith evenly-spaced indentations that hold the body of the lathapproximately14 in. (6 mm) away from solid surfaces towhich it is installed.3.2.9 water resistive barrier, na material that resists theinfiltration of liquid moistu
20、re through the building enclosuresystem.4. Delivery and Storage of Materials4.1 Delivery of Materials:4.1.1 All materials shall be delivered in the originalpackages, containers, or bundles bearing the brand-name andmanufacturers (or suppliers) identification.4.2 Storage of Materials:4.2.1 All materi
21、als shall be kept dry. Materials shall bestacked off the ground, supported on a level platform, andprotected from the weather and surface contamination.4.2.2 Materials shall be neatly stacked with care taken toavoid damage to edges, ends, or surfaces.4.2.3 Paper backed metal plaster bases shall be h
22、andledcarefully in delivery, storage, and erection to prevent punctur-ing or removal of paper.5. Materials5.1 Metallic materials including lathing, lathing accessories,furring, furring accessories, and fasteners shall be selected forcompatibility to minimize galvanic corrosion between adjacentmetall
23、ic materials installed in the cement plaster claddingassembly.5.2 Metal Plaster Bases:5.2.1 Expanded Metal LathSpecification C847, galva-nized.5.2.2 Wire Laths:5.2.2.1 Welded Wire LathSpecification C933.5.2.2.2 Woven Wire LathSpecification C1032.5.2.2.3 Paper Backed Plaster BasesSpecification C847.5
24、.3 Lathing Accessories, Furring Accessories and Fasten-ers:5.3.1 Lathing Accessories, Furring Accessories andFastenersSpecification C1861.5.3.2 The selection of an appropriate type of material forlathing accessories shall be based upon applicable surroundingclimatic and environmental conditions spec
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC10632018BSTANDARDSPECIFICATIONFORINSTALLATIONOFLATHINGANDFURRINGTORECEIVEINTERIORANDEXTERIORPORTLANDCEMENTBASEDPLASTERPDF

链接地址:http://www.mydoc123.com/p-463209.html