ASTM B591-2015 Standard Specification for Copper-Zinc-Tin and Copper-Zinc-Tin-Iron-Nickel Alloys Plate Sheet Strip and Rolled Bar《铜-镍-锌以及铜-镍-锌-铁-镍合金厚板 薄板 带材和轧制棒材的标准规格》.pdf

《ASTM B591-2015 Standard Specification for Copper-Zinc-Tin and Copper-Zinc-Tin-Iron-Nickel Alloys Plate Sheet Strip and Rolled Bar《铜-镍-锌以及铜-镍-锌-铁-镍合金厚板 薄板 带材和轧制棒材的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B591-2015 Standard Specification for Copper-Zinc-Tin and Copper-Zinc-Tin-Iron-Nickel Alloys Plate Sheet Strip and Rolled Bar《铜-镍-锌以及铜-镍-锌-铁-镍合金厚板 薄板 带材和轧制棒材的标准规格》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B591 15Standard Specification forCopper-Zinc-Tin and Copper-Zinc-Tin-Iron-Nickel AlloysPlate, Sheet, Strip, and Rolled Bar1This standard is issued under the fixed designation B591; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This spe

3、cification covers the requirements for specifiedcopper-zinc-tin alloys and copper-zinc-tin-iron-nickel alloysplate, sheet, strip, and rolled bar. The alloys and nominalcompositions are as follows:Copper AlloyUNS No.Copper,%Tin,%Zinc,%Phos.,%Iron,%Nickel,%C40500 95 1 4C40810 95.5 2.0 2.2 0.03 0.1 0.1

4、5C40850 95.5 3.0 1.3 0.1 0.1 0.1C40860 94.8 2.0 3 0.03 0.03 0.1C41100 91 0.5 8.5C41300 91 1 8C41500 91 2 7C42200 87 1 12C42500 88 2 10C42520 89.8 2.0 8 0.1 0.1 0.1C43000 85 2 13C43400 85 0.7 14.31.2 UnitsThe values stated in inch-pound units are to beregarded as standard. The values given in parenth

5、eses aremathematical conversions to SI units which are provided forinformation only and are not considered standard.2. Referenced Documents2.1 The following documents in the current issue of theAnnual Book of ASTM Standards form a part of this specifi-cation to the extent referenced herein:2.2 ASTM

6、Standards:2B248 Specification for General Requirements for WroughtCopper and Copper-Alloy Plate, Sheet, Strip, and RolledBarB601 Classification for Temper Designations for Copper andCopper AlloysWrought and CastB846 Terminology for Copper and Copper AlloysE8/E8M Test Methods for Tension Testing of M

7、etallic Ma-terialsE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE62 Test Methods for Chemical Analysis of Copper andCopperAlloys (Photometric Methods) (Withdrawn 2010)3E112 Test Methods for Determining Average Grain SizeE478 Test Methods for Chemical Analysis of Copper Alloys3. Genera

8、l Requirements3.1 The following sections of Specification B248 constitutea part of this specification:3.1.1 TerminologyDefinitions,3.1.2 Workmanship, Finish, and Appearance,3.1.3 Sampling,3.1.4 Number of Tests and Retests,3.1.5 Specimen Preparation,3.1.6 Test Methodsexcept for chemical analysis,3.1.

9、7 Significance of Numerical Limits,3.1.8 Inspection,3.1.9 Rejection and Rehearing,3.1.10 Certification,3.1.11 Test Reports (Mill),3.1.12 Packaging and Package Marking,3.1.13 Supplementary Requirements.3.2 In addition, when a section with a title identical to thatreferenced in 3.1 appears in this spe

10、cification, it containsadditional requirements, which supplement those appearing inSpecification B248.4. Terminology4.1 For definitions of terms related to copper and copperalloys, refer to Terminology B846.1This specification is under the jurisdiction ofASTM Committee B05 on Copperand Copper Alloys

11、 and is the direct responsibility of Subcommittee B05.01 onPlate, Sheet, and Strip.Current edition approved Feb. 15, 2015. Published March 2015. Originallyapproved in 1973. Last previous edition approved in 2009 as B591 09. DOI:10.1520/B0591-15.2For referenced ASTM standards, visit the ASTM website,

12、 www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section ap

13、pears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15. Ordering Information5.1 Include the following specified choices when placingorders for product under this specification, as applicable:5.1.1 ASTM desi

14、gnation and year of issue (for example,B591 XX),5.1.2 Copper Alloy UNS No. Designation (for example,C42500),5.1.3 Temper (see Section 8),5.1.4 Dimensions, that is, thickness, width, length, and soforth (see Section 12),5.1.5 Form: plate, sheet, strip, or rolled bar,5.1.6 How furnished: coils, specif

15、ic or stock lengths, with orwithout ends,5.1.7 Quantity: total weight each form, temper, and size, and5.1.8 Intended application.5.2 The following options are available but may not beincluded unless specified at the time of placing of the orderwhen required:5.2.1 Type of edge: slit, sheared, sawed,

16、square corners,round corners, rounded edges, or full rounded edges,5.2.2 Width and straightness tolerances (see Section 12),5.2.3 Heat Identification or traceability details (see 6.1.2),5.2.4 Certification,5.2.5 Mill Test Report.5.2.6 If product is purchased for agencies of the U.S.Government, see S

17、ection 11 of this specification and theSupplementary Requirements section of Specification B248 foradditional requirements, if specified.6. Materials and Manufacture6.1 Material:6.1.1 The material of manufacture shall be a form (cast bar,cake, or slab) of Copper Alloy UNS No. C40500, C40810,C40850,

18、C40860, C41100, C41300, C41500, C42200, C42500,C42520, C43000, or C43400 of such purity and soundness asto be suitable for processing into products prescribed herein.6.1.2 When specified in the contract or purchase order, thatheat identification or traceability is required, the purchasershall specif

19、y the details desired.NOTE 1Due to the discontinuous nature of the processing of castingsinto wrought products, it is not always practical to identify a specificcasting analysis with a specific quantity of finished material.6.2 Manufacture:6.2.1 The product shall be manufactured by such hotworking,

20、cold working, and annealing processes as to producea uniform wrought structure in the finished product.6.2.2 The product shall be hot or cold worked to the finishedsize and subsequently annealed, when required, to meet thetemper properties specified.6.2.3 EdgesSlit edges shall be furnished unless ot

21、herwisespecified in the contract or purchase order.7. Chemical Composition7.1 The material shall conform to the chemical composi-tional requirements specified in Table 1 for the copper alloyUNS No. designation specified in the ordering information.7.1.1 These composition limits do not preclude the p

22、resenceof other elements. By agreement between manufacturer andpurchaser, limits may be established and analysis required forunnamed elements.7.2 For alloys in which zinc is listed as “remainder,” eithercopper or zinc may be taken as the difference between the sumof the results for all elements dete

23、rmined and 100 %. When allelements in Table 1 are determined, the sum of the results shallbe 99.7 % min.8. Temper8.1 The standard tempers for products described in thisspecification are given in Table 2 and Table 3.8.1.1 Hot Rolled Temper (M20).8.1.2 Cold Rolled Tempers H01 to H10Special tempersnot

24、listed in this specification are subject to agreement betweenthe manufacturer and the purchaser.8.1.3 Annealed Tempers OS015 to OS035Special tempersnot listed in this specification are subject to agreement betweenthe manufacturer and the purchaser.8.1.4 Temper designations are defined in Classificat

25、ionB601.9. Grain Size for Annealed Tempers9.1 Grain size shall be the standard requirement for allproducts in the annealed tempers.9.2 Acceptance or rejection based upon grain size shalldepend only on the average grain size of test specimen takenfrom each of two sampling portions and each specimen s

26、hall beTABLE 1 Chemical RequirementsCopper AlloyUNS No.Composition, % max (Unless Shown as a Range)Copper Tin Lead Iron Phosphorus Nickel ZincC40500 94.0-96.0 0.7-1.3 0.05 0.05 . . . . . . remainderC40810 94.5-96.5 1.8-2.2 0.05 0.08-0.12 0.028-0.04 0.11-0.20 remainderC40850 94.5-96.5 2.6-4.0 0.05 0.

27、05-0.20 0.01-0.20 0.05-0.20 remainderC40860 94.0-96.0 1.7-2.3 0.05 0.01-0.05 0.02-0.04 0.05-0.20 remainderC41100 89.0-92.0 0.30-0.7 0.09 0.05 . . . . . . remainderC41300 89.0-93.0 0.7-1.3 0.09 0.05 . . . . . . remainderC41500 89.0-93.0 1.5-2.2 0.09 0.05 . . . . . . remainderC42200 86.0-89.0 0.8-1.4

28、0.05 0.05 0.35 . . . remainderC42500 87.0-90.0 1.5-3.0 0.05 0.05 0.35 . . . remainderC42520 88.0-91.0 1.5-3.0 0.05 0.05-0.20 0.01-0.20 0.05-0.20 remainderC43000 84.0-87.0 1.7-2.7 0.09 0.05 . . . . . . remainderC43400 84.0-87.0 0.40-1.0 0.05 0.05 . . . . . . remainderB591 152TABLE 2 Tensile Strength

29、Requirements and Approximate Rockwell Hardness Values for Rolled TempersNOTE 1Plate is generally available in only the as hot-rolled (M20) temper. Required properties for other tempers shall be agreed upon between themanufacturer and the purchaser at the time of placing the order.Temper DesignationT

30、ensile Strength,ksiA(MPa)BApproximate Rockwell HardnessB-Scale Superficial 30TCodeCName Min Max0.020 to 0.036 in. (0.51to 0.91 mm), inclOver 0.036 in.(0.91 mm)0.012 to 0.028 in. (0.30to 0.71 mm), inclOver 0.028 in.(0.711 mm)Copper Alloy UNS No. C40500M20 As hot-rolled 35 (240) 50 (345) . . . . . . .

31、 . . . . .H01 Quarter hard 41 (280) 53 (365) 30-54 34-62 36-56 38-58H02 Half hard 46 (315) 58 (400) 50-66 52-69 49-60 51-62H03 Three-quarter hard 52 (360) 64 (440) 60-72 62-74 56-66 58-68H04 Hard 58 (400) 70 (485) 66-76 68-78 60-68 62-70H06 Extra hard 63 (435) 75 (515) 71-78 72-80 65-71 66-73H08 Spr

32、ing 68 (470) 80 (550) 75-81 76-83 67-72 68-74H10 Extra spring 73 (505) 84 (580) 78-83 79-85 69-73 70-75Copper Alloy UNS No. C40810H02 Half hard 57 (395) 73 (505) 65-80 66-81 60-70 62-72H04 Hard 76 (525) 88 (605) 78-89 80-90 67-74 69-75H06 Extra hard 90 (620) 100 (690) 82-90 83-92 69-75 70-76H08 Spri

33、ng 94 (650) 102 (705) 85-92 86-94 71-77 72-78Copper Alloy UNS No. C40850H02 Half hard 57 (395) 73 (505) 65-80 67-81 60-69 62-72H04 Hard 76 (525) 89 (615) 78-88 80-90 67-74 69-75H06 Extra hard 90 (620) 100 (690) 82-91 83-93 69-75 70-76H08 Spring 94 (650) 106 (730) 85-92 87-94 72-77 73-78Copper Alloy

34、UNS No. C40860H02 Half hard 56 (385) 72 (495) 64-80 65-80 60-70 61-72H04 Hard 74 (510) 87 (600) 77-89 79-90 66-74 68-75H06 Extra hard 88 (605) 98 (675) 81-90 82-91 68-75 69-76H08 Spring 92 (635) 105 (725) 84-92 85-94 70-77 71-78Copper Alloy UNS No. C41100M20 As hot-rolled 34 (235) 50 (345) . . . . .

35、 . . . . . . .H01 Quarter hard 42 (290) 54 (370) 32-60 34-63 37-57 38-64H02 Half hard 49 (340) 60 (415) 51-68 52-70 50-62 51-67H03 Three-quarter hard 55 (380) 66 (455) 62-75 63-77 58-66 59-70H04 Hard 61 (420) 72 (495) 68-79 69-81 62-70 64-71H06 Extra hard 67 (460) 78 (540) 74-82 76-84 66-73 67-72H08

36、 Spring 73 (505) 83 (570) 78-84 77-86 69-74 70-73H10 Extra spring 78 (540) . . . 80 and over 80 and over 70 and over 71 and overCopper Alloy UNS No. C41300M20 As hot-rolled 37 (255) 50 (345) . . . . . . . . . . . .H01 Quarter hard 45 (310) 55 (380) 34-62 35-64 40-58 39-60H02 Half hard 50 (345) 62 (4

37、30) 52-70 53-72 51-63 51-64H03 Three-quarter hard 58 (400) 68 (470) 64-77 66-78 59-68 60-69H04 Hard 65 (450) 75 (515) 71-80 72-81 63-70 64-70H06 Extra hard 70 (485) 82 (565) 77-83 78-84 67-71 68-72H08 Spring 76 (525) 86 (595) 81-86 82-87 70-73 70-74H10 Extra spring 81 (560) . . . 85 and over 86 and

38、over 72 and over 73 and overCopper Alloy UNS No. C41500M20 As hot rolled 38 (260) 50 (345) . . . . . . . . . . . .H01 Quarter hard 46 (315) 56 (385) 48-73 49-75 48-65 49-67H02 Half hard 53 (365) 63 (435) 68-78 70-80 62-68 63-70H03 Three-quarter hard 57 (395) 68 (470) 73-80 75-82 65-70 66-71H04 Hard

39、64 (440) 75 (515) 78-85 79-87 69-72 69-74H06 Extra hard 70 (485) 82 (565) 81-87 82-90 70-73 70-75H08 Spring 78 (540) 89 (615) 86-92 87-93 73-76 73-77H10 Extra spring 85 (585) . . . 89 and over 90 and over 74 and over 75 and overCopper Alloy UNS No. C42200M20 As hot-rolled 40 (275) 53 (365) . . . . .

40、 . . . . . . .H01 Quarter hard 47 (325) 57 (395) 42-68 44-70 43-62 46-65H02 Half hard 54 (370) 65 (450) 64-74 66-76 58-68 61-70H03 Three-quarter hard 60 (415) 72 (495) 71-80 73-82 64-69 66-71H04 Hard 67 (460) 79 (545) 76-83 78-85 67-71 69-73H06 Extra hard 75 (515) 85 (585) 80-85 82-87 69-73 70-74H08

41、 Spring 82 (565) 92 (635) 83-88 85-90 70-74 71-75H10 Extra spring 88 (605) . . . 86 and over 86 and over 74 and over 74 and overCopper Alloy UNS No. C42500M20 As hot-rolled 40 (275) 54 (370) . . . . . . . . . . . .H01 Quarter hard 49 (340) 59 (405) 46-71 48-73 45-65 47-67H02 Half hard 57 (395) 69 (4

42、85) 67-81 69-83 63-69 65-72H03 Three-quarter hard 62 (430) 74 (510) 74-84 76-86 66-71 68-73H04 Hard 70 (485) 82 (565) 81-88 83-90 70-74 72-76H06 Extra hard 76 (525) 88 (605) 86-92 88-94 71-75 73-77H08 Spring 84 (580) 94 (650) 89-93 91-95 73-77 74-78B591 153within the limits prescribed in Table 3 whe

43、n determined inaccordance with Test Methods E112.9.3 Grain size shall be determined on a plane parallel to theflat surfaces of the product.10. Mechanical Property Requirements10.1 Tensile Strength Requirements of Rolled Tempers:10.1.1 Product furnished under this specification shall con-form to the

44、tensile requirements prescribed in Table 2 for thetemper and UNS Alloy Number specified in the orderinginformation when tested in accordance with Test MethodsE8/E8M.10.1.2 Test specimens shall be taken so that the longitudinalaxis is parallel to the direction of rolling.10.1.3 Acceptance or rejectio

45、n based upon mechanicalproperties shall depend only on tensile strength.10.2 Rockwell HardnessThe approximate Rockwell val-ues given in Table 2 and Table 4 are for general informationand assistance in testing and shall not be used as a basis forrejection.10.2.1 When performed, the hardness values sh

46、all be deter-mined using Test Methods E18.NOTE 2The Rockwell hardness test offers a quick and convenientmethod of checking for general conformity to the specification require-ments for temper, tensile strength, and grain size.11. Other Requirements11.1 Purchases for U.S. Government AgenciesWhenspeci

47、fied in the contract or purchase order, product purchasedfor an agency of the U.S. Government shall conform to thespecial government requirements specified in the supplementalrequirements given in Specification B248.12. Dimensions, Mass, and Permissible Variations12.1 The dimensions and tolerances f

48、or product describedby this specification shall be as specified in Specification B248,with particular reference to the following tables and relatedparagraphs in that specification:12.1.1 ThicknessTolerances as in Table 1.12.1.2 Width:12.1.2.1 Width Tolerances for Slit Metal and Slit Metal withRolled

49、 Edges as in Table 4.12.1.2.2 Width Tolerances for Square-Sheared Metal as inTable 5.12.1.2.3 Width Tolerances for Sawed Metal as in Table 6.TABLE 2 ContinuedTemper DesignationTensile Strength,ksiA(MPa)BApproximate Rockwell HardnessB-Scale Superficial 30TCodeCName Min Max0.020 to 0.036 in. (0.51to 0.91 mm), inclOver 0.036 in.(0.91 mm)0.012 to 0.028 in. (0.30to 0.71 mm), inclOver 0.028 in.(0.711 mm)H10 Extra spring 92 (635) . . . 92 and over 92 and over 76 and over 77 and overCopper Alloy UNS No. C42520H02 Half hard 67 (460) 82 (565) 68-83 70-85 64-71 67-73H04 Har