ASTM B369-2009(2016) Standard Specification for Copper-Nickel Alloy Castings《铜镍合金铸件的标准规格》.pdf

《ASTM B369-2009(2016) Standard Specification for Copper-Nickel Alloy Castings《铜镍合金铸件的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B369-2009(2016) Standard Specification for Copper-Nickel Alloy Castings《铜镍合金铸件的标准规格》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B369 09 (Reapproved 2016)Standard Specification forCopper-Nickel Alloy Castings1This standard is issued under the fixed designation B369; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A num

2、ber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification establishes the requirements for

3、copper-nickel alloy castings with nominal compositions shownin Table 1. These are as follows:2Copper Alloy UNS No.2Previous DesignationC96200 Alloy AC96400 Alloy B1.2 Castings of these alloys are used primarily forcorrosion-resistance applications such as in construction andfor pressure vessels, par

4、ticularly in marine pumps, valves, andfittings.1.3 These alloys are considered weldable, but they may beordered with a weld test to ensure weldability. When extensivewelding is to be performed on the casting, weldability testsshould be specified in the ordering information (5.2.6)toensure proper wel

5、ding characteristics.1.4 UnitsThe values stated in inch-pound units are to beregarded as standard. The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard.1.5 The following hazard statement applies only to Section8

6、, Weldability Test, of this specification. This standard does notpurport to address all of the safety concerns, if any, associatedwith its use. It is the responsibility of the user of this standardto establish appropriate safety and health practices anddetermine the applicability of regulatory limit

7、ations prior touse.2. Referenced Documents2.1 ASTM Standards:3B208 Practice for Preparing Tension Test Specimens forCopper Alloy Sand, Permanent Mold, Centrifugal, andContinuous CastingsB824 Specification for General Requirements for CopperAlloy CastingsB846 Terminology for Copper and Copper AlloysE

8、527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)2.2 ASME Code:4ASME Boiler and Pressure Vessel Code2.3 AWS Standard:5AWS A5.6 Specification for Copper and Copper-Alloy Arc-Welding Electrodes3. General Requirements3.1 The following sections of Specification B824 form

9、apart of this specification. In the event of a conflict between thisspecification and Specification B824, the requirements of thisspecification shall take precedence.3.1.1 Terminology (Section 3),3.1.2 Other Requirements (Section 7),3.1.3 Dimensions, Mass, and Permissible Variations (Sec-tion 8),3.1

10、.4 Workmanship, Finish, and Appearance (Section 9),3.1.5 Sampling (Section 10),3.1.6 Number of Tests and Retests (Section 11),3.1.7 Specimen Preparation (Section 12),3.1.8 Test Methods (Section 13),3.1.9 Significance of Numerical Limits (Section 14),1This specification is under the jurisdiction ofAS

11、TM Committee B05 on Copperand Copper Alloys and is the direct responsibility of Subcommittee B05.05 onCastings and Ingots for Remelting.Current edition approved April 1, 2016. Published May 2016. Originallyapproved in 1961. Last previous edition approved in 2009 as B369 09. DOI:10.1520/B0369-09R16.2

12、The UNS system for copper and copper alloys (see Practice E527) is a simpleexpansion of the former standard designation system accomplished by the additionof a prefix “C” and a suffix “00”. The suffix can be used to accommodatecomposition variations of the base alloy.3For referenced ASTM standards,

13、visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarte

14、rs, Two Park Ave., New York, NY 10016-5990, http:/www.asme.org.5Available from American Welding Society (AWS), 8669 NW 36 St., #130,Miami, FL 33166-6672, http:/www.aws.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C70

15、0, West Conshohocken, PA 19428-2959. United States13.1.10 Inspection (Section 15),3.1.11 Rejection and Rehearing (Section 16),3.1.12 Certification (Section 17),3.1.13 Test Report (Section 18),3.1.14 Product Marking (Section 19), and3.1.15 Packaging and Package Marking (Section 20).4. Terminology4.1

16、For definitions of terms relating to copper alloys, refer toTerminology B846.5. Ordering Information5.1 Orders for castings under this specification shouldinclude the following information:5.1.1 Specification title, number, and year of issue;5.1.2 Quantity of castings;5.1.3 Copper Alloy UNS Number (

17、Table 2);5.1.4 Pattern or drawing number and condition (as-cast,machined, and so forth);5.1.5 ASME Boiler and Pressure Vessel Code Requirements(Section 12); and5.1.6 When material is purchased for agencies of the U.S.Government, the Supplementary Requirements of this specifi-cation may be specified.

18、5.2 The following are optional and should be specified inthe purchase order when required:5.2.1 Pressure test or soundness requirements (SpecificationB824);5.2.2 Witness inspection (Specification B824);5.2.3 Certification (Specification B824);5.2.4 Foundry test report (Specification B824);5.2.5 Prod

19、uct marking (Specification B824);5.2.6 Weldability test (1.3, Section 8, and Table 2); and5.2.7 Approval of weld procedure and records of repairs(Section 9).6. Chemical Composition6.1 The castings shall conform to the chemical requirementsshown in Table 2 for the copper alloy UNS numbers specifiedin

20、 the purchase order.6.2 These specification limits do not preclude the presenceof other elements. Limits may be established and analysisrequired for unnamed elements agreed upon between themanufacturer or supplier and the purchaser. Copper may begiven as remainder and may be taken as the difference

21、betweenthe sum of all elements analyzed and 100 %. When all theelements in the table are analyzed, their sum shall be 99.5 %minimum.7. Mechanical Properties7.1 Mechanical properties shall be determined from sepa-rately cast test bar castings, and shall meet the requirementsshown in Table 3.8. Weldab

22、ility Test8.1 When specified in the purchase order at least one testcast as shown in Fig. 1 shall be prepared for each lot of weldinggrade castings (5.2.6).8.2 The block shall be molded, gated, and risered in such amanner to produce a sound casting without defects that mightinterfere with welding or

23、 the interpretation of the results of thetest.8.3 The groove in the test block shall be completely filledwith weld deposit metal, using the manual metallic-arc processwith18-in. (12.7-mm) or532-in. (3.97-mm) diameter copper-nickel (70-30) coated electrodes conforming to classificationAWS ECuNi of AW

24、S Specification A5.6. The interpass tem-perature need not be controlled, unless it is to be controlled infabrication.8.4 One38-in. (9.52-mm) minimum thick bend coupon (seeFig. 2), shall be removed longitudinally from the center of thewelded block by machining, sawing, abrasive cutting, or othersuita

25、ble means. Cut surfaces and edges should be sandedsmooth if necessary. The side bend specimen then shall be bent180 in a guided bend jig around a mandrel 112 in. (38.1 mm)in diameter with the weld located at the center of the bend.TABLE 1 Nominal CompositionsCopper Alloy UNS No.Composition, %Copper

26、Nickel Iron Silicon Manganese NiobiumC96200C9640087.567.010.030.01.50.70.10.50.90.8.1.0TABLE 2 Chemical RequirementsCopper Alloy UNS No.C96200Copper Alloy UNS No.C96400Min, % Max, % Min, % Max, %Copper balance balanceLead . 0.01 . 0.01Iron 1.0 1.8 0.25 1.5Nickel, incl cobalt 9.0 11.0 28.0 32.0Mangan

27、ese . 1.5 . 1.5Silicon . 0.50 . 0.50Niobium . 1.0A0.50 1.5Phosphorus . 0.02 . 0.02Sulfur . 0.02 . 0.02Carbon . 0.10 . 0.15AWhen product or casting is intended for subsequent welding applications, and sospecified by the purchaser, the niobium content shall be 0.40 % max.TABLE 3 Mechanical Requirement

28、sCopper AlloyUNS No. C96200Copper AlloyUNS No. C96400Tensile strength, min, ksiA(MPa) 45 (310) 60 (415)Yield strength,Bmin, ksiA(MPa) 25 (170) 32 (220)Elongation in 2 in. (50.8 mm), % 20 20Aksi = 1000 psi.BYield strength shall be determined as the stress producing an elongation underload of 0.5 %, t

29、hat is 0.01 in. (0.254 mm) in a gage length of 2 in. (50.8 mm).B369 09 (2016)28.5 Cracks or other open defects exceeding18 in. (3.2 mm)measured in any direction in the fusion zone or heat-affectedzone on the convex surface of the specimen after bending shallbe cause for rejection. Cracks originating

30、 at weld-beadundercuts, at weld-slag inclusions, or at casting defects shallnot be cause for rejection.9. Casting Repair9.1 Alloys included in this specification are generally weld-able. Weld repairs may be made at the manufacturers discre-tion provided each excavation does not exceed 20 % of thecas

31、ting section or wall thickness or 4 % of the casting surfacearea.9.2 Excavations that exceed those described in 9.1 may bemade at the manufacturers discretion except that when speci-fied in the purchase order (5.2.7) the weld procedure shall beapproved by the purchaser and the following record shall

32、 bemaintained:9.2.1 A sketch or drawing showing the dimensions, depth,and location of excavations;9.2.2 Post weld heat treatment, when applicable;9.2.3 Weld repair inspection results;9.2.4 Casting identification number;9.2.5 Weld procedure identification number;9.2.6 Welder identification; and9.2.7

33、Name of inspector.9.3 The castings shall not be impregnated without approvalof the purchaser.10. Sampling10.1 Test bar castings for tension testing of the copper alloyUNS numbers in this specification shall be cast to the form anddimensions shown in Fig. 1 or Fig. 2 of Practice B208.11. Test Methods

34、11.1 Analytical chemical methods are given in SpecificationB824.11.1.1 Test methods to be followed for the determination ofelements resulting from contractual or purchase order agree-ment shall be as agreed upon between the manufacturer orsupplier and the purchaser.12. ASME Requirements12.1 When spe

35、cified in the purchase order to meet ASMEBoiler and Pressure Vessel Code requirements, castings ofCopper Alloy UNS No. C96200 shall comply with the follow-ing:12.1.1 Certification requirements of Specification B824.12.1.2 Foundry test report requirements of SpecificationB824.12.1.3 Castings shall be

36、 marked with the manufacturersname, the copper alloy UNS number, and the casting qualityfactor. In addition, heat numbers or serial numbers that aretraceable to heat numbers shall be marked on all pressure-containing castings individually weighing 50 lb (22.7 kg) ormore. Pressure-containing castings

37、 weighing less than 50 lb(22.7 kg) shall be marked with either the heat number or aserial number that will identify the casting as to the month inwhich it was poured. Marking shall be in such a position as tonot injure the usefulness of the casting.13. Keywords13.1 copper-alloy castings; copper-nick

38、el castings; UNSNo. C96200; UNS No. C96400TABLE 4 Metric Conversion Values for Figs. 1 and 2in. (mm) in. (mm)18 (3.18) 134 (44.4)38 (9.52) 234 (69.8)34 (19.0) 3 (76.2)1 (25.4) 312 (88.9)118 (28.6) 6 (152)NOTE 1For metric equivalents see Table 4.FIG. 1 Cast Block for Weldability TestNOTE 1For metric

39、equivalents see Table 4.FIG. 2 Weldability Test BlockB369 09 (2016)3SUPPLEMENTARY REQUIREMENTSThe following supplementary requirements shall apply only when specified by the purchaser in theinquiry, contract, or order, for agencies of the U.S. government.S1. Referenced DocumentsS1.1 The following do

40、cuments of the issue in effect on dateof material purchase form a part of this specification to theextent referenced herein:S1.1.1 ASTM Standard:B900 Practice for Packaging of Copper and Copper AlloyMill Products for U.S. Government AgenciesS1.1.12 Federal Standards:6Fed. Std. No. 102 Preservation,

41、Packaging, and PackingLevelsFed. Std. No. 123 Marking for Shipment (Civil Agencies)Fed. Std. No. 185 Identification Marking of Copper andCopper-Base Alloy Mill ProductsS1.1.3 Military Standards:6MIL-STD-129 Marking for Shipment and StorageMIL-STD-248 Welded and Brazing Procedure in Perfor-mance Qual

42、ificationMIL-STD-278 Welding and Casting StandardS2. SoundnessS2.1 Castings shall meet the soundness requirements ofMIL-STD-278 for the category, sub-category, and criticalitylevel specified in the purchase order.S3. Pressure TestS3.1 Castings shall meet the pressure test requirements ofMIL-STD-278.

43、S4. Weld RepairS4.1 All repair welding shall be in accordance with MIL-STD-278 using welders and welding procedures qualified inaccordance with MIL-STD-248.S5. Quality AssuranceS5.1 Responsibility for Inspection:S5.1.1 Unless otherwise specified in the contract or pur-chase order, the manufacturer i

44、s responsible for the perfor-mance of all inspection and test requirements specified. Exceptas otherwise specified in the contract or purchase order, themanufacturer may use his own or any other suitable facilitiesfor the performance of the inspection and test requirementsunless disapproved by the p

45、urchaser at the time the order isplaced. The purchaser shall have the right to perform any of theinspections or tests set forth when such inspections and testsare deemed necessary to ensure that the material conforms toprescribed requirements.S6. Product MarkingS6.1 The castings shall be permanently

46、 marked in accor-dance with MIL-STD-792 and include specification and alloynumber, pattern or drawing number, lot number, and manufac-turers name or trademark.S7. Preparation for DeliveryS7.1 Preservation, Packaging, and Packing:S7.1.1 Military AgenciesThe material shall be separatedby size, composi

47、tion, grade, or class and shall be preserved andpackaged, Level A or C, packed, Level A, B, or C as specifiedin the contract or purchase order, in accordance with therequirements of Practice B900.S7.1.2 Civil AgenciesThe requirements of Fed. Std. No.102 shall be referenced for definitions of the var

48、ious levels ofpackaging protection.S7.2 Marking:S7.2.1 Military AgenciesIn addition to any special mark-ing required by the contract or purchase order, marking forshipment shall be in accordance with MIL-STD-129.S7.2.2 Civil AgenciesIn addition to any special markingrequired by the contract or purch

49、ase order, marking forshipment shall be in accordance with Fed. Std. No. 123.SUMMARY OF CHANGESCommittee B05 has identified the location of selected changes to this standard since the last issue (B369 06)that may impact the use of this standard. (Approved April 1, 2009.)(1) Revised the document to re-order the position of theGeneral Requirements Section. This permits a more expedientreference to tensile testing requirements and methods, andreference to Specification B824 General Requirements.(2) Made some minor editorial modifications.6Available from DL