ARMY MIL-STD-644 A CHG NOTICE 5-1992 VISUAL INSPECTION STANDARDS AND INSPECTION PROCEDURES FOR INSPECTION OF PACKAGING PACKING AND MARKING OF SMALL ARMS AMMUNITION《轻武器弹药包装和标志检验的视觉检.pdf

《ARMY MIL-STD-644 A CHG NOTICE 5-1992 VISUAL INSPECTION STANDARDS AND INSPECTION PROCEDURES FOR INSPECTION OF PACKAGING PACKING AND MARKING OF SMALL ARMS AMMUNITION《轻武器弹药包装和标志检验的视觉检.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-STD-644 A CHG NOTICE 5-1992 VISUAL INSPECTION STANDARDS AND INSPECTION PROCEDURES FOR INSPECTION OF PACKAGING PACKING AND MARKING OF SMALL ARMS AMMUNITION《轻武器弹药包装和标志检验的视觉检.pdf（88页珍藏版）》请在麦多课文档分享上搜索。

1、g - io- IL- 3 December 196% SUPERSEDING MIL-STD-644 22 October 1958 NOTICE 2 29 MAR 1974 INSERTED NOTICE 3 83 MAR 1995 INSERTED Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-644A NOTICE 5 1 May 1992 MILITARY SPECIFICATION VISUAL INSPECTION

2、STANDARDS AND INSPECTION PROCEDURES FOR INSPECTION OF PACKAGING, PACKING AND MARKING OF SMALL ARMS AMMUNITION TO ALL HOLDERS OF MIL-STD-644A: 1. The following pages of MIL-STD-644A have been revised and supersede the pages listed: New Page Date Superseded Date 5 1 May 1992 5 10 January 1991 6 3 Dece

3、mber 1962 6 Reprinted without change 2. Retain this notice page and insert before the table of contents. 3. Holders of MIL-STD-644A will verify that page changes and additions indicated above have been entered. This notice page will be retained as a check sheet-. This issuance, together with appende

4、d pages, is a separate publication. Each notice is to be retained by stocking points until the military standard is completely revised or canceled. Custodians: Army-AR Navy-OS Air Force-70 Preparing activity: (Project 1305-0312) Army-AR AMSC N/A FSC 1305 DISTRIBUTION STATEMENT A. 0 Approved for publ

5、ic release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-LINCH - POUND I MIL-STD-644A NOTICE 4 10 January 1991 MILITARY STANDARD VISUAL INSPECTION STANDARDS AND INSPECTION PROCEDURES FOR INSPECTION OF PACKAGING, PACKING

6、AND MARKING OF SMALL ARMS AMMUNITION TO ALL HOLDERS OF MIL-STD-644A: 1. THE FOLLOWING PAGES OF MIL-STD-644A HAVE BEEN REVISED AND SUPERSEDE THE PAGES LISTED: NEW PAGE DATE SUPERSEDED DATE PAGE 3 10 January 1991 3 3 March 1975 4 3 December 1962 4 REPRINTED WITHOUT CHANGE 5 10 January 1991 5 3 Decembe

7、r 1962 6 3 December 1962 6 REPRINTED WITHOUT CHANGE 2. RETAIN THIS NOTICE PAGE AND INSERT BEFORE THE TABLE OF CONTENTS. 3. Holders of MIL-STD-644A will verify that page changes and additions indicated above have been entered. This notice page will be retained as a check sheet. This issuance, togethe

8、r with appended pages, is a separate publication. Each notice is to be retained by stocking points until the military standard is completely revised or canceled. Custodians: Army - AR Navy - OS Air Force - 70 Preparing activity: (Project 1305-OD57) Army - AR AMSCNA FSC 1305 RBI!l%R Approved for publ

9、ic release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. .- :. i . . . _. -_ . %. -. -. =-. .i . *. I-. - t4 I L-STD-644A NOT I CE-3 3 March 1975 MILITARY STANDARD VISUAL INSPECTION STANDARDS AND NSPECTIBN PROCEDURES -

10、 FOR INSPECTION OF PACWG ING, PACKING AND MARKING OF: SMALL ARMS AMMUN TION _- TO ALL- HOLDERS OF Ml b-STB-644A. 1. THE FOLLOWING PAGE IS 00 BE ADDED: . NEW PAGE P DATE SUPERSEDED PAGE 3 ,. . . i -3 * 3 MPC iws 2. 3. RETAIN THIS NOTICE PAGE AND INSERT BEFORE THE TAabE OF CONTENTS. Holders of MI b-ST

11、D-644W wi 11 ver i fy that the page addi tion indicated above has been entePed. This issuance, together with the appended page, is a separate publication. Each notice is to be retained by stocking points until the Military Standard is completely revised OP cancelled. The notice page Will be WhiRed a

12、% B check sheet. CUStOdian5: Army - HU c Navy - QS Air Force - 70 Review activities: Army - MU Air QPCE? - 78 . ., - Navy - OS - - . . ._ . _. . -. .- . . FSC 1305 -I ._ ._ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIb-STD-644A NOTICE 3 13 9997

13、111 0030337 T rn-Srn-ii.toii contents (type, caliber, etc.). .3.1.2,3.1 Visual standards for defects 5 through i3 are illustrated in the appendix (figs. 3-14), .5.1.3.1 Prior to envelope sealing, examina- tion shall be performed to assure that mark- ings on the envelope corresponds with the markings

14、 on the envelope contents. The oc- currerice of this defect will be brought to the attention of the manufacturer and he will be requested to correct his process. Continued occurrence of this defect will be cause for discontinuance of Government acceptance. .5.1.3.2 The acceptable quality levels for

15、envelope package defects shall be as follows : Major -. . -. . _ - . . . . . . 1.00 Minor . - -. _. ._ 2.5 Perce ri 1 5.1.3.3 Classification of defects. Etiveloie puclcage defects Major hfi?ro? 1. Torn, ripped or improperly sealed X - _ - 2. Iniproper packaging of envelopes in X envelope. container.

16、 ra tor s. envelope contents (type, caliber, etc.). 3. Missing OP improper fillers or sepa- _ X 4. Incorrect or illegible identification of _ X 5. Incorrect, illegible or missing ainniuni- -_ X tioii lot number. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

17、rom IHS-,-,-MIL-STD-644A CHG NOTICE 4 33 = 9999933 0097724 4 i 5.1.3.3.1 Visual standards for defects 1.4 and 5 are illustrated in the appendix (figs. 15 and a 16). .- 5.1.4 Bulk package. 5.1.4.1 the acceptable quality levels for bulk . package defects shall be as follows: Percent 2.5 Minor _._- 5.1

18、.4.2 classification of defects. 1. Missing or improper fillers, tubes or- X 2. Improper packaging of cartridges in- X 3. Missing cartridge(s) - X Bulk package defects Minor separators. container. 5.1.4.2.1 There are no visual standard illustrated in the appendix for bulk package. 5.1.5 Clip package.

19、 5.1.5.1 The acceptable quality levels for clip package defects shall be as follows: Percent 1.00 2.5 5.1.5.2 Classification of defects. Major or Clip, package defects Minor Minor 1. Missing cartridge(s) x .- 2. Rusty, excessively oiled or otherwise -_- X 3. Missing or torn carton (when required) x

20、.- 4. Missing or improper fillers or separators. x .-.- 5. improper packaging of clipped x _ defective clips* ammunition container. *Defect is major if clip will not function as intended: otherwise minor. If questionable, functioning test shali be made in appropriate service weapon or magazine, whic

21、hever is applicable. 5.1.5.2.1 Visual standards for defects 3 and 4 are illustrated in the appendix (figs. 17-26). 5.1.6 Metallic linked belt package. 5.1.6.1 In some instances, metallic links show in the appendix are of a predecessor design but the visual standard is applicable to the present desig

22、n. 5.1.6.2 The twist test (fiw.1) and the ull test shall be performed to detect broken or soft links in the belt of linked cartridges. 3 Supersedes page 3 of Notice 3 MIL-STD-644A NOTICE 4 Links that fail as a result of these tests shall be dismantled and scrapped and the cartridges visually inspect

23、ed prior to rebelting. 5.1.6.2.1 With the belt extended full length on a table, grasp one end and flip it 180 degrees to its other side. The twisting action which progressively moves along the belt to the free end has enough snap to cause failure of weak links. After the test, the belt shall be insp

24、ected for any fractured or broken links that may be present. 5.1.6.2.2 One end of the belt shall be attached to a suitable hook on a horizontal table and the load indicated below applied to the other end; the belt being in contact with the table during the application of the load. I2iuEEB LQBP Ma 5.

25、56mm 19 lbs. 30 lbs. 1.62mm 25 lbs. 35 lbs. .30 25 lbs. 35 lbs. .50 100 lbs. 115 lbs. 20mm 115 Ibs. 135 lbs. In lieu of a ked load application, a testing device may be used which stretches the belts to predetermined lengths correlated with the loads prescribed above. The length of these belts shall

26、be verified frequently: however, ali M17 type linked belts shall be verified for a length of not greater than thirteen (13) feet, eight point five (8.5) inches when measured from center to center of the end primers with an applied load of 10 plus one minus O pounds. Subsequent to the test, inspectio

27、n of the belts for broken and stretched links shail be performed. 5.1.6.2.3 When 20mm cartridges are belted using the M17 link a “frozen“ link shall be detected by means of a flexibility test: 5.1.6.2.3.1 The belt shall hinge freely and fold over smoothly without kinking when the belt is pulled over

28、 itself until belt is completely reversed. This procedure shall then be repeated after the belt has been reversed to assure full motion of the belt when flexed from either side and in either direction. 5.1.6.2.3.2 A minimum of twenty five (25) cartridges per belt shall be used for this test. If pack

29、ing instructions require belts of greater length, the connecting links used to lengthen the belts shall be flexed after assembling in both directions to assure free hinging. 5.1.6.2.3.3 A “frozen“ M17 link detected by means of this flexibility test is critical and shall be cause for rejection of lot

30、, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-644A CHG NOTICE 4 33 l e- MIL-STD-644A 3 December 1962 .5.1.6,3 The iiccept;ible qiiality level foi. nietallic link belt package defects shall be as follows : 31 ajo r . ._ 1.00 M iiior . - .

31、- - 2.5 PL!ri r .lliijor !ur ,11i11irr 2, Iiicurrwt. ill1yik)Ic or iilissill s- 3. Torii, rippctl or otierwise de- s. 4. Missing cartridge(s) or cIipi,si s .- 5. Rusty, excessively oiled or otlier- X 6. 3Iissii1g ur torii ciirtui1 i. JIissiiip 01 iiilllroper fillers or x _ 8. Iiiiproper packipiiig o

32、f clipped s _ 9. Improper pac;ik;tgiiiK of batido- 10. Missiiig iiiegaziiie filler (heii . X -_ 11. Missing safety pin (whcii . x _. aiiiniiiiiitioii lot iiiiiiiber. fective hiidoleer. vise defectivc clips.: s se p:i Ia to r s. a ni ni ii ti it i oii i ti I ia II dol iw I. leer (s) in coiitniiier. x

33、 requiiwl). required). Iefeci is mejur if clip will nut function as intended; other- wise minor. If qiiestionnblc. functiuiiiiip test shall be made in apirroiirintc scivice veaiuir or rnignzine. whichever is niipli- cnble. 5.1.7.2.1 VisUil standards for defects 2 through 4 are illustrated in the app

34、endix (figs. 57-66). Defects G and 7 (figs. 17-26). Defects 8 ant1 O (figs. 67-69), 5.1.7.3 in h!?t.ion to the above irispection, when linked ammunition is packaged in car- tons in bandoleers, the inspection procedures shall also incliitle lhose listed Linder 5.1.6, hletallic linked belt package. .

35、5.2 Packaged and sealed container. Pliase II. .j.2.1 Wate)*pj*oof envelopes. 5.2.1.1 The acceptable quality levels for envelope defects shall be as follows : Pcrcettf Major _ -. . _ 1.0 Minor . _ 2.5 5.2.1.2 Classification of defects. Envelope defects hlajr Minor 1. Torn, ripped, or improperly seale

36、d X _ 2. Incorrect, illegible or niissing am- X _ 3. Other niarkings incorrect, missing or - X :,2,2 Gasket sealecl ammunition boxes. .5.2.2,1 Box leak test. envelope. munition lot number. illegible. I 1 i 1 I 1 1 I I 1 e; I I i 1 I I l I I I I I l I 1 1 Provided by IHSNot for ResaleNo reproduction

37、or networking permitted without license from IHS-,-,-M%E=SI!l3-644A 3 June I965 i 5.i.6.5. Classification of defects Ela 10% Minor X 4a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-b44A CHG NOTICE 5 13 m 9999931 0108300 i m 5.2.2.1.1 Tap w

38、ater at ambient temperature shall be used in the bell jar for the box leak test (fig.2). 5.2.2.1.2 Each box of the inspection sample shall be submerged under water in the bell jar with the cover of the box toward the inspector. The bell jar shall be closed and a pressure differential, as specified f

39、or the particular box packed, established. The cable attached to the lid shall be snapped to release trapped air bubbles on the box. When turbulence in the water has ceased, the box shall be observed for a period of 15 seconds. 5.2.2.1.3 Any escape of air from the interior of a box under the conditi

40、ons of paragraph 5.2.2.1.2 constitutes a leaker. However, for the purpose of acceptance inspection, a leaker is one which permits the escape of a total of five or more bubbles from one or more leaking areas during the observation time of 15 seconds. 5.2.2.1.4 The location of the leak(s) (cover. bott

41、om, side, side seam, or gasket), shall be reported. 5.2.2.2 The acceptable quality levels for gasket sealed ammunition box defects shall be as fol1 ow s : Physical characteristics, paint and markings: Percent 1.00 2.5 1.0 Major _- Minor _- Gasket sealing: 5.2.2.3 Classification of defects. Gasket Ph

42、ysical characteristics Major-Minor Major _- sealed ammunition box defects. 1. Incorrectly closed and secured box x _ 2. Severe dents, buckles, or other damage - X 3. Scratches or abrasions exposing bare _ X 4. Incorrect, illegible, or missing x 5. Other markings, incorrect, missing, - X 6. Incorrect

43、 pain op ink-.- _._ .- X 7. baker 89 defied _._._._._. x .- metal. Markings ammunition lot number. or illegible. Gasket sealing MIGSTD-644A NOTICE 5 5.3 Overpacks and overpack contents. Phase III. 5.3.1 Wireboundwooden boxes. 5.3.1.1 Bar coding shall be applied to the wireboundwooden box in accordan

44、ce with MIL- STD-129 or the applicable marking drawing. The bar code must be machine readable. 5.3.1.2 The acceptable quality levels for wireboundwooden box defects shall be as follows: Assembly and Sed 1. Unfastened outside binding wire 2. Unfastened inside binding wire 3. Missing end 4. Side, top

45、or bottom extending beyond end cleat more than V8 in. End cleat extending beyond side, top or bottom more than Y8 in. 6. Gap larger than V4 in. between end of batten and cleat. 7.Gap larger than Y4 in. between side of batten and cleat. and the fact that the Government may have formulated, furnished,

46、 or in any way supplied the said drawings, specifications, or other. data, is not to be regarded by implication or other- wise as in any manner licensing the holder or any other person or corporation, or con- veying iiiiy rights or permission to niiintfac- tiire, use. or sell any patented invent ion

47、 that niay iii any way be related thereto. Copy :vailahiliy Notice. Copics of spccitic:iiioiis, standards, drawinm, and pul)licatioiis requiretl by contractors in connection with specific- procurenient functions should be obtained from the procuring agency or as directed by the contractinc oicer. Co

48、pies of this stantlard for Military use niay be obtained as indicated in the Foreword to the Indes of Military Specifications and Staiidards. Copies of this standard niay be obtained for other than official use by individuals. Ariiis, and ron- tractors. from the Superintendent of Docunients, U. S. Government Printing Office. Wastiiiigton 25, D. C. Both the titlc and the identifying synibol nuniber should be stipulated when requ