ARMY MIL-DTL-3628 133-1996 BADGE IDENTIFICATION HONOR GUARD COAST GUARD《徽章 海岸警卫队荣誉卫兵身份识别徽章》.pdf

《ARMY MIL-DTL-3628 133-1996 BADGE IDENTIFICATION HONOR GUARD COAST GUARD《徽章 海岸警卫队荣誉卫兵身份识别徽章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 133-1996 BADGE IDENTIFICATION HONOR GUARD COAST GUARD《徽章 海岸警卫队荣誉卫兵身份识别徽章》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-DTL-362/L33 9999906 2025037 789 m /NOT MEASUREMENT SENSITIVE 1 MIL-DTL-3628/133 15 November i996 SUPERSEDING 21 September 1994 MIL-B-41809/36C DETAIL SPECIFICATION SHEET BADGE, IDENTIFICATION, HONOR GUARD, COAST GUARD This specification is approved for use by all Departments and Agencies of the

2、 Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the issue of MIL-DTL-3628 listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation. MATERIAL: Red Br

3、ass DASH NO. DIMENSIONS: -2: Miniature Size -1: Regular Size I HEIGHT: -1: 1-9/32 inches (3.25 cm) (REF) -2: 23/32 inch (1.83 cm) (REF) -1: 2 inches (5.08 cm) (REF) -2: 1-1/8 inches (2.86 cm) (REF) -1: 0.065 inch k 0.010 inch (0.165 cm f 0.025 cm) -2: 0.050 inch k 0.010 inch (0.127 cm f 0.025 cm) WI

4、DTH : THICKNESS (At Edge) FINISH: Gold Plated, Mirror-like Polished and shall match TIOH Metal Finish Chip Number 6. AMSC N/A FSC 8455 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 of 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without

5、 license from IHS-,-,-flIL-DTL-3628/133 9999906 2025038 615 = MIL-DTL-3628/133 NOTES : Government furnished hub or die. 1. The term (REF) refers to the measurements taken from the 2. The attaching device for Dash No. -1 shall be three prongs with wing type clutches. Two prongs shall be centered on t

6、he reverse of the top ribbon scroll, 1/8 inch i 1/32 inch (0.32 cm i 0.08 cm) from each edge. The third prong shall be centered on the reverse of the bottom ribbon scroll. 3. Theattaching device for Dash No. -2 shall be two prongs .with wing type clutches. equidistant from each end and 5/8 inch k 1/

7、32 inch (1.59 cm i 0.08 cm) apart. The prong shall be located on the horizontal center line, CHANGES FROM PREVIOUS ISSUE: revision to identify changes with respect to the previous issue due to the extent of the changes. Marginal notations are not use in this Custodian: Army - IH Coast Guard - CG Review activities: DLA - CT Preparing activity: Army - IH (Project .No. 8455-0866) 2 of 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-