AIR FORCE A-A-59513-2004 GENERATOR SIGNAL 10 MHZ TO 26.5 GHZ《信号产生器(10兆赫至26.5吉赫)》.pdf

《AIR FORCE A-A-59513-2004 GENERATOR SIGNAL 10 MHZ TO 26.5 GHZ《信号产生器(10兆赫至26.5吉赫)》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE A-A-59513-2004 GENERATOR SIGNAL 10 MHZ TO 26.5 GHZ《信号产生器(10兆赫至26.5吉赫)》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 A-A-59513 15 March 2004 COMMERCIAL ITEM DESCRIPTION GENERATOR, SIGNAL 10 MHz to 26.5 GHz The General Services Administration has authorized the use of this commercial item description (CID) by all federal agencies. 1. SCOPE. This Commercial Item Description (CID) describes a synthesized sweep/signa

2、l generator capable of generating signals over the frequency range of 10 MHz to 26.5 GHz with analog sweep capabilities with high stability time-base. The This CID is meant as a minimum requirement for a synthesized sweep/signal generator, herein referred to as synthesizer, in which only those manuf

3、acturers that meet or surpass the following requirements are supplied per this CID. 2. SALIENT CHARACTERISTICS 2.1 The equipment shall be capable of operation within the accuracies, limits, and specifications herein. 2.2 The equipment covered by this CID shall be commercially available equipment and

4、 may modified to the extent necessary to meet the following description. The equipment shall be Class 3, in accordance with MIL-PRF-28800. 2.3 Order of Precedence. In the event of a conflict between the text of this CID and the references cited herein (except for associated detail specifications, sp

5、ecification sheets or MS standards) the text of this CID shall take precedence. Nothing in this CID, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. AMSC N/A FSC 6625 Comments, suggestions, or questions on this document should be addressed to W

6、R-ALC/LEEC, Robins AFB, GA 31098-1611. Since contact information can change, you may want to verify the currency of this address information using the ASSIST online database at www.dodssp.daps.mil. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

7、HS-,-,-A-A-59513 22.4 Safety. The equipment shall be UL (underwriters Laboratories) listed and approved and/or shall comply with the safety requirements of MIL-PRF-28800 for the classification stated herein. 2.5 Frequency. The synthesizer shall have a frequency range of 10 MHz to 26.5 GHz with a min

8、imum resolution of 1 Hz. 2.6 Output Power. The synthesizer shall provide the following minimum output power capability: +8 to -100 dBm from 10 MHz to 26.5 GHz. 2.7 Output Level Flatness. Variation of the output levels of the synthesizer shall not exceed the following specifications: +/- 0.7 dB for 1

9、0 MHz to 2.0 GHz +/- 1.0 dB for 2.0 GHz to 6.6 GHz +/- 1.2 dB for 6.6 GHz to 12.3 GHz +/- 1.5 dB for 12.3 GHz to 18.6 GHz +/- 1.8 dB for 18.6 GHz to 26.5 GHz 2.8 Modulation. No modulation capability is required for the synthesizer. 2.9 Time Base. The synthesizer shall have an internal 10 MHz time ba

10、se with an aging rate = 5 X 10-10 parts per day. The synthesizer shall also be capable of utilizing an external time base. The synthesizer shall have a rear panel BNC connector capable of accepting 5 MHz and 10 MHz external time bases. 2.10 Time Base Output. The synthesizer shall have a rear panel 1

11、0 MHz time base output. 2.11 Harmonics. The harmonic content of the output of the synthesizer shall not exceed the following specifications: -30 dBc for 10 MHz to 2 GHz -60 dBc for 2 GHz to 20 GHz -40 dBc for 20 GHz to 26.5 GHz 2.12 Sub-harmonics and Multiples. All sub-harmonics and multiples of sub

12、-harmonics of the output signal of the synthesizer shall not exceed -60 dBc. 2.13 Spurious Outputs. The non-harmonically related spurious emissions shall be -60dBc for RF frequencies from 10 MHz to 26.5 GHz. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

13、S-,-,-A-A-59513 32.14 Single Sideband Phase Noise. At a 1 kHz offset from the carrier, when measured in a 1 Hz bandwidth in the CW mode, single sideband phase noise shall be as follows: Frequency Frequency dBc Range Offset (Hz) (Hz) 10MHz to 1050MHz 100 -95 1050MHz to 26.5GHz 100 -65 10MHz to 1050MH

14、z 1k -119 1050MHz to 26.5GHz 1k -88 10MHz to 1050MHz 10k -122 1050MHz to 26.5GHz 10k -98 10MHz to 1050MHz 100k -119 1050MHz to 26.5GHz 100k -92 2.15 Output Connector. The synthesizers output connector shall be Type K female and two Type K male to Type N(f) adapters shall be supplied. The adapters ar

15、e not to be used when connecting the synthesizer to the down converter as a local oscillator. The Type K male to Type N(f) adapters will only be utilized when using the synthesizer as a stand alone source at frequencies below 18 GHz. 2.16 Radio Frequency (RF) Cable. A Type K male on one end and WSMA

16、 female cable to connect the synthesizer, when it is being used as a local oscillator, to the down converter shall be supplied. When in this configuration the down converter is on top of the synthesizer, and its input is on the left side of the instrument. 2.17 Dimensions and Weight. The synthesizer

17、/local oscillator shall be designed for mounting in a standard 19 inch EIA electronic equipment rack. The depth of the synthesizer/local oscillator, from the back of the front panel shall not exceed 22 inches. No controls or fittings shall project more than 1 1/2 inches from the face of the front pa

18、nel. The height shall be 8.75 inches. The weight of the synthesizer shall not exceed 50 pounds. 2.18 Digital Input/Output Capability. The synthesizer/local oscillator shall include an IEEE-488-1987 standard I/O interface. The Interface Function subset implemented shall have or exceed the following c

19、apabilities: INTERFACE FUNCTION MINIMUM ACCEPTABLE SUBSET Source Handshake SH1 Acceptor Handshake AH1 Talker T6 Listener L4 Remote Local RL1 Parallel Poll PP0 Device Clear DC1 Device Trigger DT1 Service Request SR1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

20、from IHS-,-,-A-A-59513 4The instrument shall use bi-directional data transmission in ASCII coded format. 2.19 Power Consumption. An assembled power cord for 110 to 120 volt operation shall be provided with each AC powered instrument. Each AC powered instrument shall have an AC power switch and a fro

21、nt panel indication when AC power is applied. The power consumption of the synthesizer shall not exceed 500 Watts. 2.20 Rack-mount Capability. The synthesizer shall be furnished with rack mount kit for mounting in a standard 19 inch Electronic Industries Association (EIA) rack. The rack mount kit fo

22、r the synthesizer shall include front handles, rack ears, chassis slides for a 20-inch depth synthesizer rack. 2.20 Manuals. The synthesizer shall be delivered with operator, maintenance, and illustrated parts manuals. Format and quantity shall be as specified in the contract or order. 3. REGULATORY

23、 REQUIREMENTS 3.1 The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE 4.1 Product Conformance. The products provided shall meet the salient character

24、istics of this CID, conform to the producers own drawings, specifications, standards and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 4.2 Metric Products. Products manufactured

25、to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within the specified tolerances using conversion tables contained in the latest revision of Federal Standard No. 376, and all other requirements of this CID are met. If a prod

26、uct manufactured to metric dimensions exceeds the tolerances specified in the inch/pound units, a request should be made to the contracting officer to determine if the product is acceptable. 4.3 The contracting officer has the option of accepting or rejecting the product. 5. PACKING. Preservation, p

27、acking, and marking shall be as specified in the contract or order. 6. NOTES. 6.1 Sources of documents. 6.1.1 Military Specifications, Standards, and Handbooks referenced herein may be obtained from the Standardization Documents Order Desk, 700 Robbins Ave, Bldg 4, Section D, Philadelphia, PA 19111-

28、5094. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59513 56.1.2 The Code of Federal Regulations (CFR) may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC, 20402. 6.1.3 IEEE standards can be obt

29、ained from IEEE Customer Service Center, 445 Hoes Lane, P.O. Box 1331, Piscataway, NJ 08855-1331, and U.S.A. Phone: 1-800-678-4333 (Toll-Free, USA & Canada), 1-732-981-0060 (Worldwide), Fax: 1-732-981-9667. MILITARY INTERESTS Custodian: Preparing Activity: Air Force - 99 Air Force 84 Agent: Air Force 99 Project 6625-0921 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-