BS PD CEN TS 14758-2-2016 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene with mineral modifiers (PP-MD) Guidance for the assessme.pdf

《BS PD CEN TS 14758-2-2016 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene with mineral modifiers (PP-MD) Guidance for the assessme.pdf》由会员分享，可在线阅读，更多相关《BS PD CEN TS 14758-2-2016 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene with mineral modifiers (PP-MD) Guidance for the assessme.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、PD CEN/TS 14758-2:2016 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene with mineral modifiers (PP-MD) Part 2: Guidance for the assessment of conformity BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06PD CEN/TS 14758-2:2016 PU

2、BLISHED DOCUMENT National foreword This Published Document is the UK implementation of CEN/TS 14758-2:2016. It supersedes DD CEN/TS 14758-2:2007 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/88/1, Plastics piping for non-pressure applications. A

3、 list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Stand

4、ards Limited 2016 ISBN 978 0 580 92491 0 ICS 23.040.01; 93.030 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 July 2016. Amendments issued since publicati

5、on Date Text affectedPD CEN/TS 14758-2:2016TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 14758-2 July 2016 ICS 23.040.01; 93.030 Supersedes CEN/TS 14758-2:2007 English Version Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene

6、with mineral modifiers (PP-MD) - Part 2: Guidance for the assessment of conformity Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement enterrs sans pression - Polypropylne avec modificateurs minraux (PP-MD) - Partie 2 : Guide pour lvaluation de la conformit

7、 Kunststoff-Rohrleitungssysteme fr erdverlegte drucklose Abwasserkanle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 2: Empfehlungen fr die Beurteilung der Konformitt This Technical Specification (CEN/TS) was approved by CEN on 9 June 2016 for provisional application. The

8、period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this

9、CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is rea

10、ched. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

11、Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitat

12、ion in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 14758-2:2016 EPD CEN/TS 14758-2:2016 CEN/TS 14758-2:2016 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Abbreviated terms 8 5 Gener

13、al 9 6 Testing and inspection 9 6.1 Material specification 9 6.2 Grouping . 9 6.2.1 General 9 6.2.2 Size groups . 9 6.2.3 Fitting groups 10 6.3 Type testing 10 6.4 Batch release tests . 13 6.5 Process verification tests 15 6.6 Audit tests . 16 6.7 Indirect tests 18 6.8 Test records . 19 Annex A (inf

14、ormative) Basic test matrix . 20 Bibliography . 21 PD CEN/TS 14758-2:2016 CEN/TS 14758-2:2016 (E) 3 European foreword This document (CEN/TS 14758-2:2016) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. Attent

15、ion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 14758-2:2007. EN 14758 consists of the following parts, under the general t

16、itle Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene with mineral modifiers (PP-MD): Part 1: Specifications for pipes, fittings and the system Part 2: Guidance for the assessment of conformity (the present TS) According to the CEN/CENELEC Internal Regulations

17、, the national standards organisations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Ita

18、ly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. PD CEN/TS 14758-2:2016 CEN/TS 14758-2:2016 (E) 4 Introduction Figures 1 and 2 are intended to provide general information on the co

19、ncept of testing and organization of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type testing (TT), batch release test (BRT), process verification test (PVT), and audit test (AT), this document details the applicable characteristics to be assessed as

20、 well as the frequency and sampling of testing. A typical scheme for the assessment of conformity of materials, pipes, fittings, joints or assemblies by manufacturers is given in Figure 1. Figure 1 Typical scheme for the assessment of conformity by a manufacturer A typical scheme for the assessment

21、of conformity of materials, pipes, fittings, joints or assemblies by manufacturers, including certification, is given in Figure 2. Figure 2 Typical scheme for the assessment of conformity by a manufacturer, including certification PD CEN/TS 14758-2:2016 CEN/TS 14758-2:2016 (E) 5 1 Scope This Technic

22、al Specification gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 14758 intended to be included in the manufacturers quality plan as part of the quality management system and for the establishment of certifi

23、cation procedures. NOTE In order to help the reader, a basic test matrix is given in Annex A. In conjunction with EN 14758-1 this document is applicable to solid wall piping systems made of polypropylene modified with mineral(s) (PP-MD) intended to be used for: non-pressure underground drainage and

24、sewerage outside the building structure (application area code “U”); and non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code “D”) and outside the building structure. This is reflected in the marking of products by “U” and “UD”

25、. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any ame

26、ndments) applies. EN 14758-1:2012, Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system 3 Terms and definitions For the purposes of this document, the terms and definition

27、s given in EN 14758-1 and the following apply. 3.1 certification body impartial body, governmental or non-governmental, possessing the necessary competence and responsibility to carry out certification of conformity according to given rules of procedure and management Note 1 to entry: A certificatio

28、n body is preferably compliant with EN ISO/IEC 17021-1 1. 3.2 inspection body body, that performs inspection Note 1 to entry: A body can be an organization or part of an organization. Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 2. 3.3 testing laboratory laborato

29、ry which measures, tests, calibrates or otherwise determines the characteristics of the performance of materials and products PD CEN/TS 14758-2:2016 CEN/TS 14758-2:2016 (E) 6 Note 1 to entry: In the context of this part of EN 14758, the materials and products can be subjected to type testing, batch

30、release testing, process verification testing, audit testing and witness testing, as applicable. Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 3. 3.4 quality management system management system to direct and control an organization with regard to quality Note 1

31、to entry: Requirements for quality management systems are given in EN ISO 9001 4. 3.5 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.6 type testing TT testing performed to prove that the m

32、aterial, product, joint or assembly is capable of conforming to the requirements given in the relevant standard Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly provided that the process verification tests are done regularly. 3.7 batc

33、h release test BRT test performed by or on behalf of the manufacturer on a batch of materials or products, which has to be satisfactorily completed before the batch can be released 3.8 process verification test PVT test performed by or on behalf of the manufacturer on materials, products or joints a

34、t specific intervals to confirm that the process continues to be capable of producing products which conform to the requirements given in the relevant standard Note 1 to entry: Such tests are not required to release batches of materials or products and are carried out as a measure of process control

35、. 3.9 audit test AT test performed by a test laboratory on behalf of an inspection body or certification body to confirm that the material, product, joint or assembly continues to conform to the requirements given in the relevant standard and to provide information to assess the effectiveness of the

36、 quality management system 3.10 indirect test IT test performed by or on behalf of the manufacturer, different from that specified test for that particular characteristic, having previously verified its correlation with the specified test PD CEN/TS 14758-2:2016 CEN/TS 14758-2:2016 (E) 7 3.11 witness

37、 test WT test accepted by an inspection or a certification body for type testing and/or audit testing, which is carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or certification body, qualified in testing 3.12 material generic term for compositions

38、 of compounds/formulations grouped by families, expressed by generic names, e.g. polypropylene, stainless steel, brass or EPDM Note 1 to entry: Definition from European Commission, Directorate-General for Enterprise and Industry, Sub- group on Product Testing Procedures (EC, DG ENT and IND, SG PTP).

39、 3.13 compound/formulation clearly defined homogenous mixture of base polymer with additives, i.e. antioxidants, pigments, stabilizers and others, at a dosage level necessary for the processing and the intended use of the final product 3.14 material batch clearly identified quantity of a given homog

40、eneous compound/formulation manufactured under uniform conditions and defined and identified by the compound/formulation manufacturer 3.15 product pipe, fitting, or valve of a clearly identified type intended to be a part of a piping system which the manufacturer puts on the market 3.16 product batc

41、h clearly identified collection of products, manufactured consecutively or continuously under the same conditions, using the same compound/formulation conforming to the same specification Note 1 to entry: The production batch is defined and identified by the product manufacturer. 3.17 lot clearly id

42、entifiable sub-division of a batch for inspection purposes 3.18 sample one or more products drawn from the same production batch or lot, selected at random without regard to their quality Note 1 to entry: The number of products in the sample is the sample size. 3.19 group collection of similar produ

43、cts from which samples are selected for testing purposes PD CEN/TS 14758-2:2016 CEN/TS 14758-2:2016 (E) 8 3.20 component product manufactured out of a specific composition compound/formulation, brought to the market as part of another product or as a spare part 3.21 joint connection between two prod

44、ucts 3.22 assembled product assembled final product using two or more single parts 3.23 thermoplastics fabricated fitting fitting produced from pipe and/or from injection-moulded fittings by thermoforming, solvent- cementing or welding 3.24 assembly product that can be dismantled into a set of compo

45、nents EXAMPLE A test piece consisting of various products. 3.25 sampling plan specification of the type of sampling to be used combined with the operational specification of the entities or increments to be taken, the samples to be constituted and the measurements or tests to be made EXAMPLE A speci

46、fic plan which indicates the number of units of products or assemblies to be inspected. 3.26 product type generic description of a product EXAMPLE A pipe or fitting or valve or their main parts, of the same design, from a particular compound. 3.27 cavity (moulding) space within a mould to be filled

47、to form the moulded product EXAMPLE That part of an injection mould which gives the form to the injection-moulded product. 4 Abbreviated terms To avoid misunderstanding, the abbreviations in this clause are defined as being the same in each language. For the same reason, the terms are given in the t

48、hree languages, English, French and German. EN FR DE AT audit test essai daudit berwachungsprfung PD CEN/TS 14758-2:2016 CEN/TS 14758-2:2016 (E) 9 BRT batch release test essai de libration de campagne de fabrication Freigabeprfung einer Charge IT indirect test essai indirect indirekte Prfung PVT pro

49、cess verification test essai de vrification du procd de fabrication Prozessberprfung TT type test essai de type Typprfung WT witness testing essai tmoin Prfung unter Aufsicht 5 General Materials, products, joints and assemblies shall conform to the requirements given in EN 14758-1. Products and assemblies shall be produced by the manufacturer under a quality management system which includes a quality plan. It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO