IEC 62343-3-2-2016 Dynamic modules - Part 3-2 Performance specification templates - Optical channel monitor《动态模块 第3-2部分 性能规格模板 光通道监测仪》.pdf

《IEC 62343-3-2-2016 Dynamic modules - Part 3-2 Performance specification templates - Optical channel monitor《动态模块 第3-2部分 性能规格模板 光通道监测仪》.pdf》由会员分享，可在线阅读，更多相关《IEC 62343-3-2-2016 Dynamic modules - Part 3-2 Performance specification templates - Optical channel monitor《动态模块 第3-2部分 性能规格模板 光通道监测仪》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62343-3-2 Edition 1.0 2016-05 INTERNATIONAL STANDARD Dynamic modules Part 3-2: Performance specification templates Optical channel monitor IEC 62343-3-2:2016-05(en) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2016 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, n

2、o part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC c

3、opyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switz

4、erland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept

5、 under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Te

6、chnical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also give

7、s information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org T

8、he worlds leading online dictionary of electronic and electrical terms containing 20 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary 65 000

9、electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish t

10、o give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 62343-3-2 Edition 1.0 2016-05 INTERNATIONAL STANDARD Dynamic modules Part 3-2: Performance specification templates Optical channel monitor INTERNATIONAL ELECTROTECHNICAL

11、 COMMISSION ICS 33.180.99, 33.180.01 ISBN 978-2-8322-3364-1 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. 2 IEC 62343-3-2:2016 IEC 2016 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Nor

12、mative references. 6 3 Terms and definitions 6 4 Performance specification template 6 Annex A (informative) Background and additional information on this specification template . 9 A.1 Background information on the structure of this specification template . 9 A.1.1 Selecting “directionally correct”

13、terminology 9 A.1.2 Logical sequence of parameters in Table 1 . 9 A.1.3 Performance parameters hierarchical structure . 10 A.2 Additional information about reference measurement bandwidth . 10 Bibliography . 12 Table 1 Optical channel monitor specification template . 7 IEC 62343-3-2:2016 IEC 2016 3

14、INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DYNAMIC MODULES Part 3-2: Performance specification templates Optical channel monitor FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC N

15、ational Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Pu

16、blicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- gov

17、ernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC

18、 on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accep

19、ted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote internation

20、al uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the lat

21、ter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users shou

22、ld ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other dama

23、ge of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of

24、the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent right

25、s. International Standard IEC 62343-3-2 has been prepared by subcommittee 86C: Fibre optic systems and active devices, of IEC technical committee 86: Fibre optics. The text of this document is based on the following documents: CDV Report on voting 86C/1324/CDV 86C/1371/RVC Full information on the vo

26、ting for the approval of this document can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62343 series, published under the general title Dynamic modules, can be found

27、on the IEC website. 4 IEC 62343-3-2:2016 IEC 2016 The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication w

28、ill be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IEC 62343-3-2:2016 IEC 2016 5 INTRODUCTION An optical channel monitor (OCM) is a dynamic module that measures the optical characteristics, mainly power and

29、 frequency, of each channel present in a dense wavelength division multiplexing (DWDM) transmission line. The OCM is typically connected to an optical tap coupler which directs to the OCM anywhere between 1 % and 5 % of the optical signal in the fibre-optic transmission line. The data reported by th

30、e OCM are used in a reconfigurable optical add/drop multiplexer (ROADM) to dynamically equalize the power in the optical channels and to monitor the performance of the channels continuously over the lifetime of the system. 6 IEC 62343-3-2:2016 IEC 2016 DYNAMIC MODULES Part 3-2: Performance specifica

31、tion templates Optical channel monitor 1 Scope This part of IEC 62343 provides a performance specification template for optical channel monitors. The objective of this performance specification template is to provide a framework for the performance specification of the optical channel monitor. Addit

32、ional specification parameters may be included for detailed product specifications or performance specifications. However, specification parameters specified in this document should not be removed from the detail product specifications or performance specifications. This document outlines the parame

33、ters that are used to specify the performance of the optical channel monitor. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated

34、references, the latest edition of the referenced document (including any amendments) applies. IEC 61280-2-9, Fibre optic communication subsystem test procedures Part 2-9: Digital systems Optical signal-to-noise ratio measurement for dense wavelength-division multiplexed systems IEC 61300-3-21, Fibre

35、 optic interconnecting devices and passive components Basic test and measurement procedures Part 3-21: Examinations and measurements Switching time IEC 61300-3-29, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-29: Examinations and measurement

36、s Spectral transfer characteristics of DWDM devices IEC 62074-1, Fibre optic interconnecting devices and passive components Fibre optic WDM devices Part 1: Generic specification IEC 62343, Dynamic modules General and guidance 3 Terms and definitions For the purposes of this document, the terms and d

37、efinitions given in IEC 62343 and IEC 61280-2-9 apply. 4 Performance specification template This specification template is a comprehensive compilation of all the performance parameters that may be relevant to optical channel monitors. Table 1 includes a column that indicates if a parameter is requir

38、ed or optional. The required parameters include the performance IEC 62343-3-2:2016 IEC 2016 7 parameters that are deemed necessary to form a minimal specification. The optional parameters can be specified in addition to the required parameters depending on the specific requirements of the transmissi

39、on system for which it is designed. The product specification template is given in Table 1. The R/O column refers to whether that particular specification item could be considered required or optional. The notation of “na” signifies that no specification is provided in that cell. All Min. and Max. c

40、ells left blank shall be filled in with a specification. Table 1 Optical channel monitor specification template No . Parameter name R/ O Min. Max. Unit Test method Notes 1 Input channel plan R THz a 2 Channel frequency range O THz IEC 62074-1 b 3 Input channels frequency spacing tolerance R n/a val.

41、 THz Under consideration c, f 4 Input channels power dynamic range R dB Under consideration 5 Input channels non-uniformity R n/a dB Under consideration 6 Input adjacent channels non-uniformity O n/a dB Under consideration 7 Input channels non-uniformity for channel identification O n/a dB Under con

42、sideration c 8 Input adjacent channels non-uniformity for channel identification O n/a dB Under consideration c 9 Input total band power dynamic range for channel measurements O dBm Under consideration 10 Input total band power dynamic range for total band power measurements O dBm Under consideratio

43、n 11 Input OSNR dynamic range R dBm Under consideration 12 Input channels bit rates O Gb/s d 13 Reference measurement bandwidth R nominal value IEC 61300-3-29, IEC 62074-1 e 14 Noise equivalent bandwidth O nominal value Under consideration e 15 Channel power absolute error R n/a val. dB Under consid

44、eration 16 Channel power relative error R n/a dB Under consideration 17 Channel power variability R n/a dB Under consideration 18 Channel power resolution interval O n/a dB Under consideration 19 Channel power polarization dependent error O n/a dB Under consideration 20 Total band power absolute err

45、or O n/a val. dB Under consideration 21 Total band power relative error O n/a dB Under consideration 22 Total band power variability O n/a dB Under consideration 23 Total band power resolution interval O n/a dB Under consideration 24 Frequency absolute error O n/a val. GHz Under consideration f 25 F

46、requency relative error O n/a GHz Under consideration 26 Frequency variability O n/a GHz Under consideration 27 Frequency resolution interval O n/a GHz Under consideration 28 Frequency polarization dependent error O n/a dB Under consideration 29 OSNR absolute error O n/a val. dB Under consideration

47、f 30 OSNR relative error O n/a dB Under consideration 8 IEC 62343-3-2:2016 IEC 2016 No . Parameter name R/ O Min. Max. Unit Test method Notes 31 OSNR variability O n/a dB Under consideration 32 OSNR resolution interval O n/a dB Under consideration 33 OSNR polarization dependent error O n/a dB Under

48、consideration 34 Back reflection R n/a dB Under consideration 35 Operating temperature R C - 36 Storage temperature R C - 37 Operating relative humidity R % - 38 Storage relative humidity R % - 39 Response time R n/a ms IEC 61300-3-21 40 Repeatability time interval R n/a ms Under consideration a Inp

49、ut channel plan is a parameter that is well suited in the context of DWDM transmission systems operating on fixed ITU grids, as defined in ITU-T G.694.1, of equal channel spacing. In such applications, the frequency band parameter is considered optional, as it can be derived using its definition and the input channel plan specification. However in the context of DWDM transmission systems operating on flexible ITU grids of varying channel spacing, the input channel p