IEC 61158-3-4-2014 Industrial communication networks - Fieldbus specifications - Part 3-4 Data-link layer service definition - Type 4 elements《工业通讯网络.数据总线规范.第3-4部分 数据联络层设备定义.4型元件》.pdf

《IEC 61158-3-4-2014 Industrial communication networks - Fieldbus specifications - Part 3-4 Data-link layer service definition - Type 4 elements《工业通讯网络.数据总线规范.第3-4部分 数据联络层设备定义.4型元件》.pdf》由会员分享，可在线阅读，更多相关《IEC 61158-3-4-2014 Industrial communication networks - Fieldbus specifications - Part 3-4 Data-link layer service definition - Type 4 elements《工业通讯网络.数据总线规范.第3-4部分 数据联络层设备定义.4型元件》.pdf（56页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61158-3-4 Edition 2.0 2014-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial communication networks Fieldbus specifications Part 3-4: Data-link layer service definition Type 4 elements Rseaux de communication industriels Spcifications des bus de terrain Partie 3-4: Dfinition des service

2、s de la couche liaison de donnes Elments de type 4 IEC 61158-3-4:2014-08(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2014 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec

3、tronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please

4、contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y

5、compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit n

6、ational de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publi

7、shes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published.

8、IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - w

9、ww.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new

10、IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French

11、, with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publicat

12、ions issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec

13、.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publ

14、ications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Sp

15、cifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, com

16、it dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une foi

17、s par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 14 langues additionnelles. Egalement appel Vocabulaire Elect

18、rotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 55 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publicat

19、ions des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61158-3-4 Edition 2.0 2014-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial communica

20、tion networks Fieldbus specifications Part 3-4: Data-link layer service definition Type 4 elements Rseaux de communication industriels Spcifications des bus de terrain Partie 3-4: Dfinition des services de la couche liaison de donnes Elments de type 4 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMIS

21、SION ELECTROTECHNIQUE INTERNATIONALE U ICS 25.040.40; 35.100.20; 35.110 PRICE CODE CODE PRIX ISBN 978-2-8322-1712-2 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publicatio

22、n from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 61158-3-4:2014 IEC 2014 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope . 7 General . 7 1.1Specifications 7 1.2Conformance . 7 1.3 2 Normative references . 8 3 Term

23、s, definitions, symbols, abbreviations and conventions . 8 Reference model terms and definitions 8 3.1Service convention terms and definitions . 9 3.2Data-link service terms and definitions 10 3.3Symbols and abbreviations 12 3.4Conventions 13 3.5 4 Data-link service and concepts . 14 Overview . 14 4

24、.1Types and classes of data-link service 15 4.2Functional classes . 15 4.3Facilities of the connectionless-mode data-link service 15 4.4Model of the connectionless-mode data-link service 15 4.5Sequence of primitives 16 4.6Connectionless-mode data transfer functions 18 4.7 5 DL-management service . 2

25、0 Scope and inheritance . 20 5.1Facilities of the DL-management service . 20 5.2Model of the DL-management service 21 5.3Constraints on sequence of primitives . 21 5.4Set 21 5.5Get 22 5.6Action 23 5.7Event 24 5.8 Bibliography 25 Figure 1 Relationship of PhE, DLE and DLS-users . 14 Figure 2 Confirmed

26、 and unconfirmed UNITDATA request time-sequence diagram 17 Figure 3 Repeated confirmed request time-sequence diagram . 17 Figure 4 State transition diagram for sequences of primitives at one DLSAP 18 Figure 5 Sequence of primitives for the DLM action service . 21 Table 1 Summary of DL-connectionless

27、-mode primitives and parameters 17 Table 2 Unitdata transfer primitives and parameters 18 Table 3 Control-status error codes . 20 Table 4 Summary of DL-management primitives and parameters . 21 Table 5 DLM-Set primitive and parameters 22 IEC 61158-3-4:2014 IEC 2014 3 Table 6 DLM-Get primitive and pa

28、rameters 22 Table 7 DLM-Action primitive and parameters 23 Table 8 DLM-Event primitive and parameters . 24 4 IEC 61158-3-4:2014 IEC 2014 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INDUSTRIAL COMMUNICATION NETWORKS FIELDBUS SPECIFICATIONS Part 3-4: Data-link layer service definition Type 4 elements

29、FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the

30、 electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted t

31、o technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the Internationa

32、l Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each te

33、chnical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Pu

34、blications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their n

35、ational and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment

36、services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees,

37、servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publi

38、cation, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibi

39、lity that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. Attention is drawn to the fact that the use of the associated protocol type is restricted by its intellectual-property-right ho

40、lders. In all cases, the commitment to limited release of intellectual-property-rights made by the holders of those rights permits a layer protocol type to be used with other layer protocols of the same type, or in other type combinations explicitly authorized by its intellectual-property-right hold

41、ers. NOTE Combinations of protocol Types are specified in IEC 61784-1 and IEC 61784-2. International Standard IEC 61158-3-4 has been prepared by subcommittee 65C: Industrial networks, of IEC technical committee 65: Industrial-process measurement, control and automation. This second edition cancels a

42、nd replaces the first edition published in 2007. This edition constitutes an editorial revision with only minor editorial changes. IEC 61158-3-4:2014 IEC 2014 5 This edition includes the following significant changes with respect to the previous edition: a) editorial improvements; b) editorial corre

43、ctions. The text of this standard is based on the following documents: FDIS Report on voting 65C/759/FDIS 65C/769/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance wi

44、th ISO/IEC Directives, Part 2. A list of all the parts of the IEC 61158 series, under the general title Industrial communication networks Fieldbus specifications, can be found on the IEC web site. The committee has decided that the contents of this publication will remain unchanged until the stabili

45、ty date indicated on the IEC web site under http:/webstore.iec.ch in the data related to the specific publication. At this date, the publication will be: reconfirmed; withdrawn; replaced by a revised edition, or amended. 6 IEC 61158-3-4:2014 IEC 2014 INTRODUCTION This part of IEC 61158 is one of a s

46、eries produced to facilitate the interconnection of automation system components. It is related to other standards in the set as defined by the “three-layer” fieldbus reference model described in IEC 61158-1. Throughout the set of fieldbus standards, the term “service” refers to the abstract capabil

47、ity provided by one layer of the OSI Basic Reference Model to the layer immediately above. Thus, the data-link layer service defined in this standard is a conceptual architectural service, independent of administrative and implementation divisions. IEC 61158-3-4:2014 IEC 2014 7 INDUSTRIAL COMMUNICAT

48、ION NETWORKS FIELDBUS SPECIFICATIONS Part 3-4: Data-link layer service definition Type 4 elements 1 Scope General 1.1 This part of IEC 61158 provides common elements for basic time-critical messaging communications between devices in an automation environment. The term “time-critical” is used to rep

49、resent the presence of a time-window, within which one or more specified actions are required to be completed with some defined level of certainty. Failure to complete specified actions within the time window risks failure of the applications requesting the actions, with attendant risk to equipment, plant and possibly human life. This standard defines in an abstract way the ext