IEC 60927-2007 Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements《灯附件.起动装置(辉光起动器除外).性能要求》.pdf

《IEC 60927-2007 Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements《灯附件.起动装置(辉光起动器除外).性能要求》.pdf》由会员分享，可在线阅读，更多相关《IEC 60927-2007 Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements《灯附件.起动装置(辉光起动器除外).性能要求》.pdf（64页珍藏版）》请在麦多课文档分享上搜索。

1、 INTERNATIONAL STANDARD IECCEINORME INTERNATIONALE60927Third editionTroisime dition2007-06Auxiliaries for lamps Starting devices (other than glow starters) Performance requirements Appareils auxiliaires pour lampes Dispositifs damorage (autres que starters lueur) Exigences de performance Reference n

2、umber Numro de rfrence IEC/CEI 60927:2007 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photoc

3、opying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your loca

4、l IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilm

5、s, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays

6、de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic a

7、nd related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC o

8、n-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published d

9、etails twice a month all new publications released. Available on-line and also by email. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: cscie

10、c.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des

11、 publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la

12、 CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publication

13、s de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visite

14、z le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 INTERNATIONAL STANDARD IECCEINORME INTERNATIONALE60927Third editionTroisime dition2007-06Auxiliaries for lamps Starting devices (other than glow starters) Performance requirements Appareils au

15、xiliaires pour lampes Dispositifs damorage (autres que starters lueur) Exigences de performance V Commission Electrotechnique InternationaleInternational Electrotechnical Commission PRICE CODE CODE PRIX For price, see current cataloguePour prix, voir catalogue en vigueur 2 60927 IEC:2007 CONTENTS FO

16、REWORD.4 1 Scope.6 2 Normative references .6 3 Definitions 7 4 General requirements for tests .8 4.1 Ambient conditions, test quantity and sequence of tests8 4.2 Supply voltage.8 4.3 Corresponding safety requirements .8 4.4 Immunity .8 4.5 Relation to lamp standards8 5 Marking 8 6 Performance requir

17、ements for starters (other than glow starters) for fluorescent lamps .9 6.1 Starting test.9 6.1.1 Starting test quantity .9 6.1.2 Conditions of acceptance 9 6.1.3 Conditions of test 9 6.1.4 Starters having a mechanical switching element10 6.1.5 Starters having an electronic switching element 11 6.1.

18、6 Non-reoperating level 12 6.1.7 Maximum pre-heat current (lamp fails to start).13 6.1.8 Interruption of starter function13 6.2 Endurance test 13 6.2.1 Test quantity13 6.2.2 Test conditions 13 6.2.3 Starters replaceable without tools13 6.2.4 Starters not intended for replacement13 6.2.5 Conditions o

19、f acceptance 13 6.3 Deactivated lamp test14 6.3.1 Test quantity14 6.3.2 Test conditions 14 6.3.3 Starters with a mechanical switching element but without cut-out 14 6.3.4 Starters with an electronic switching element but without cut-out.14 6.3.5 Starters with a mechanical switching element and with

20、thermal cut-out.14 6.3.6 Starters with an electronic switching element and electronic cut-out 15 6.3.7 Condition of acceptance 15 7 Performance requirements for ignitors15 7.1 Starting test.15 7.1.1 Test quantity15 7.1.2 Test conditions 15 7.1.3 Conditions of acceptance 15 7.1.4 Switching speed 16 7

21、.1.5 Pulse voltage.16 7.1.6 Repetition rate, pulse position, width and height of starting pulse for triggered ignitors .16 60927 IEC:2007 3 7.1.7 Ignition energy for non-triggered ignitors .16 7.2 Non-reoperating level 16 7.3 Endurance test 17 7.3.1 Test quantity17 7.3.2 Test conditions 17 7.3.3 Ign

22、itors without replaceable switching elements 17 7.3.4 Ignitors with switching elements replaceable without tools.17 7.3.5 Ignitors with additional cut-outs .18 7.3.6 Conditions of compliance.18 Annex A (normative) Ballasts to be used for life testing .21 Annex B (informative) Explanation of starting

23、 conditions for electronic starters with an electronic switching element .22 Annex C (informative) A guide to quoting product life and failure rate 30 Bibliography31 Figure 1 Pulse voltage measurement for starting devices.19 Figure 2 Ignition energy measurement for non-triggered starting devices.20

24、Figure B.1 Cathode heating current requirements for electronic starters with electronic switching element .26 Figure B.2 Interpretation of effective heating current27 Figure B.3 Starters which remove pre-heating current when open-circuit voltages are elevated28 Figure B.4 Starters which have open-ci

25、rcuit voltage transition times higher than 100 ms29 Table 1 Starting aid requirements 9 4 60927 IEC:2007 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ AUXILIARIES FOR LAMPS STARTING DEVICES (OTHER THAN GLOW STARTERS) PERFORMANCE REQUIREMENTS FOREWORD 1) The International Electrotechnical Commission (I

26、EC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in additi

27、on to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee intereste

28、d in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with c

29、onditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC

30、National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for th

31、e way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any

32、 IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users shou

33、ld ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other dama

34、ge of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of

35、the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent right

36、s. International standard IEC 60927 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical committee 34: Lamps and related equipment. This third edition of IEC 60927 replaces the second edition (1996) and its Amendments 1 (1999) and 2 (2004). Subclause 4.5 has been inserted i

37、n order to install an obligatory link to the relevant lamp standard. This standard is to be used in conjunction with IEC 61347-1 and IEC 61347-2-1. It was established on the basis of the second (2007) edition of IEC 61347-1 and on the basis of the first (2000) edition and Amendment 1 (2005) of IEC 6

38、1347-2-1. 60927 IEC:2007 5 The text of this standard is based on the following documents: FDIS Report on voting 34C/783/FDIS 34C/797/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been draft

39、ed in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the

40、 publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 60927 IEC:2007 AUXILIARIES FOR LAMPS STARTING DEVICES (OTHER THAN GLOW STARTERS) PERFORMANCE REQUIREMENTS 1 Scope This International Standard specifies performance requirements for starting devices (starters an

41、d ignitors) for tubular fluorescent and other discharge lamps for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, which produce starting pulses not greater than 5 kV. This standard is used in conjunction with IEC 61347-1 and IEC 61347-2-1. NOTE 1 All glow starters for fluorescent and other dis

42、charge lamps including thermal relay/cut-outs will be included in IEC 60155. NOTE 2 There are regional standards regarding the regulation of EMC requirements for end-products like luminaires and independent control gear. In a luminaire, the control gear is dominant in this respect. Control gear, tog

43、ether with other components, should comply with these standards. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docume

44、nt (including any amendments) applies. IEC 60081, Double-capped fluorescent lamps Performance specifications IEC 60192, Low-pressure sodium vapour lamps Performance specifications IEC 60598-1:2003, Luminaires Part 1: General requirements and tests1)Amendment 1 (2006) IEC 60662, High-pressure sodium

45、vapour lamps IEC 60901, Single-capped fluorescent lamps Performance specifications IEC 60921, Ballasts for tubular fluorescent lamps Performance requirements IEC 60923, Auxiliaries for lamps Ballasts for discharge lamps (excluding tubular fluorescent lamps) Performance requirements IEC 61167, Metal

46、halide lamps IEC 61347-1, Lamp controlgear - General and safety requirements IEC 61347-2-1, Lamp controlgear Particular requirements for starting devices (other than glow starters) _ 1)A consolidated edition 6.1 exists, including IEC 60598-1 (2003) and its Amendment 1 (2006). 60927 IEC:2007 7 IEC 61

47、347-2-9, Lamp controlgear Particular requirements for ballasts for discharge lamps (excluding fluorescent lamps) IEC 61547, Equipment for general lighting purposes EMC immunity requirements 3 Terms and definitions For the purposes of this document, the terms and definitions of IEC 61347-2-1 together

48、 with the following apply. 3.1 starter with mechanical switching element starter which provides cathode pre-heating current and lamp-starting pulse(s) by mechanical means (e.g. thermal or magnetic) 3.2 starter with electronic switching element starter which provides cathode pre-heating current and l

49、amp-starting voltage(s) or pulse(s) by electronic means and contains no moving parts 3.3 deactivated lamp lamp in which one or both cathodes are deprived of emitting material but neither of which is broken 3.4 non-re-operating level reduced level of voltage and/or current at which a starting device must not re-operate after the completion o