IEC 60927 Edition 3.1-2013 Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements《灯附件.起动装置(辉光启动器除外).性能要求》.pdf

《IEC 60927 Edition 3.1-2013 Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements《灯附件.起动装置(辉光启动器除外).性能要求》.pdf》由会员分享，可在线阅读，更多相关《IEC 60927 Edition 3.1-2013 Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements《灯附件.起动装置(辉光启动器除外).性能要求》.pdf（130页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60927 Edition 3.1 2013-09 CONSOLIDATED VERSION VERSION CONSOLIDE Auxiliaries for lamps Starting devices (other than glow starters) Performance requirements Appareils auxiliaires pour lampes Dispositifs damorage (autres que starters lueur) Exigences de performance IEC60927:2007+A1:2013 colourins

2、ideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permissio

3、n in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for fur

4、ther information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Co

5、mit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +

6、41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and relat

7、ed technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The adva

8、nced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just P

9、ublished details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms

10、 in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de l

11、a CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la C

12、EI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (

13、numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Di

14、sponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues addit

15、ionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60927 Edition 3.1 2013-09 CONSOLIDATED VERSION VE

16、RSION CONSOLIDE Auxiliaries for lamps Starting devices (other than glow starters) Performance requirements Appareils auxiliaires pour lampes Dispositifs damorage (autres que starters lueur) Exigences de performance INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE

17、ICS 29.140.30 ISBN 978-2-8322-1105-2 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous ave

18、z obtenu cette publication via un distributeur agr. colourinsideIEC 60927 Edition 3.1 2013-09 REDLINE VERSION VERSION REDLINE Auxiliaries for lamps Starting devices (other than glow starters) Performance requirements Appareils auxiliaires pour lampes Dispositifs damorage (autres que starters lueur)

19、Exigences de performance IEC60927:2007+A1:2013 colourinside 2 60927 IEC:2007 +A1:2013 CONTENTS FOREWORD . 4 1 Scope . 6 2 Normative references . 6 3 Definitions 7 4 General requirements for tests . 8 4.1 Ambient conditions, test quantity and sequence of tests 8 4.2 Supply voltage. 8 4.3 Correspondin

20、g safety requirements . 8 4.4 Immunity . 8 4.5 Relation to lamp standards 8 5 Marking 8 6 Performance requirements for starters (other than glow starters) for fluorescent lamps . 9 6.1 Starting test . 9 6.1.1 Starting test quantity . 9 6.1.2 Conditions of acceptance 9 6.1.3 Conditions of test 9 6.1.

21、4 Starters having a mechanical switching element 10 6.1.5 Starters having an electronic switching element 11 6.1.6 Non-reoperating level 12 6.1.7 Maximum pre-heat current (lamp fails to start) . 13 6.1.8 Interruption of starter function 13 6.2 Endurance test 13 6.2.1 Test quantity 13 6.2.2 Test cond

22、itions 13 6.2.3 Starters replaceable without tools 13 6.2.4 Starters not intended for replacement 13 6.2.5 Conditions of acceptance 13 6.3 Deactivated lamp test 14 6.3.1 Test quantity 14 6.3.2 Test conditions 14 6.3.3 Starters with a mechanical switching element but without cut-out 14 6.3.4 Starters

23、 with an electronic switching element but without cut-out . 14 6.3.5 Starters with a mechanical switching element and with thermal cut-out . 14 6.3.6 Starters with an electronic switching element and electronic cut-out 15 6.3.7 Condition of acceptance 15 7 Performance requirements for ignitors 15 7.

24、1 Starting test . 15 7.1.1 Test quantity 15 7.1.2 Test conditions 15 7.1.3 Conditions of acceptance 15 7.1.4 Switching speed 16 7.1.5 Pulse voltage . 16 7.1.6 Repetition rate, pulse position, width and height of starting pulse for triggered ignitors . 16 60927 IEC:2007 3 +A1:2013 7.1.7 Ignition ener

25、gy for non-triggered ignitors . 16 7.2 Non-reoperating level 16 7.3 Endurance test 17 7.3.1 Test quantity 17 7.3.2 Test conditions 17 7.3.3 Ignitors without replaceable switching elements 17 7.3.4 Ignitors with switching elements replaceable without tools . 17 7.3.5 Ignitors with additional cut-outs

26、 . 18 7.3.6 Conditions of compliance . 18 Annex A (normative) Ballasts to be used for life testing . 21 Annex B (informative) Explanation of starting conditions for electronic starters with an electronic switching element . 22 Annex C (informative) A guide to quoting product life and failure rate 30

27、 Bibliography 31 Figure 1 Pulse voltage measurement for starting devices . 19 Figure 2 Ignition energy measurement for non-triggered starting devices . 20 Figure B.1 Cathode heating current requirements for electronic starters with electronic switching element . 26 Figure B.2 Interpretation of effec

28、tive heating current 27 Figure B.3 Starters which remove pre-heating current when open-circuit voltages are elevated 28 Figure B.4 Starters which have open-circuit voltage transition times higher than 100 ms 29 Table 1 Starting aid requirements 9 4 60927 IEC:2007 +A1:2013 INTERNATIONAL ELECTROTECHNI

29、CAL COMMISSION _ AUXILIARIES FOR LAMPS STARTING DEVICES (OTHER THAN GLOW STARTERS) PERFORMANCE REQUIREMENTS FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). T

30、he object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Speci

31、fications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations

32、 liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters e

33、xpress, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Com

34、mittees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC Nati

35、onal Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no

36、 marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, se

37、rvants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publica

38、tion, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibili

39、ty that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. This Consolidated version of IEC 60927 bears the edition number 3.1. It consists of the third edition (2007) documents 34C/783/FD

40、IS and 34C/797/RVD and its amendment 1 (2013) documents 34C/951/CDV and 34C/977/RVC. The technical content is identical to the base edition and its amendment. In this Redline version, a vertical line in the margin shows where the technical content is modified by amendment 1. Additions and deletions

41、are displayed in red, with deletions being struck through. A separate Final version with all changes accepted is available in this publication. This publication has been prepared for user convenience. 60927 IEC:2007 5 +A1:2013 International standard IEC 60927 has been prepared by subcommittee 34C: A

42、uxiliaries for lamps, of IEC technical committee 34: Lamps and related equipment. This standard is to be used in conjunction with IEC 61347-1 and IEC 61347-2-1. It was established on the basis of the second (2007) edition of IEC 61347-1 and on the basis of the first (2000) edition and Amendment 1 (2

43、005) of IEC 61347-2-1. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of the base publication and its amendment will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“

44、 in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The “colour inside” logo on the cover page of this publication indicates that it contains colours which are considered to be useful for

45、 the correct understanding of its contents. Users should therefore print this publication using a colour printer. 6 60927 IEC:2007 +A1:2013 AUXILIARIES FOR LAMPS STARTING DEVICES (OTHER THAN GLOW STARTERS) PERFORMANCE REQUIREMENTS 1 Scope This International Standard specifies performance requirement

46、s for starting devices (starters and ignitors) for tubular fluorescent and other discharge lamps for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, which produce starting pulses not greater than 5 kV. This standard is used in conjunction with IEC 61347-1 and IEC 61347-2-1. NOTE 1 All glow sta

47、rters for fluorescent and other discharge lamps including thermal relay/cut-outs will be included in IEC 60155. NOTE 2 There are regional standards regarding the regulation of EMC requirements for end-products like luminaires and independent control gear. In a luminaire, the control gear is dominant

48、 in this respect. Control gear, together with other components, should comply with these standards. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the late

49、st edition of the referenced document (including any amendments) applies. IEC 60081, Double-capped fluorescent lamps Performance specifications IEC 60192, Low-pressure sodium vapour lamps Performance specifications IEC 60598-1:2003, Luminaires Part 1: General requirements and tests1)Amendment 1 (2006) IEC 60662, High-pressure sodium vapour lamps IEC 60901, Single-capped fluorescent lamps Performan