IEC 60512-25-9-2008 Connectors for electrical equipment - Tests and measurements - Part 25-9 Signal integrity tests - Test 25i Alien crosstalk《电气设备用连接器.试验和测量.第25-9部分 信号完整性试验.试验25i 不同串音干扰》.pdf

《IEC 60512-25-9-2008 Connectors for electrical equipment - Tests and measurements - Part 25-9 Signal integrity tests - Test 25i Alien crosstalk《电气设备用连接器.试验和测量.第25-9部分 信号完整性试验.试验25i 不同串音干扰》.pdf》由会员分享，可在线阅读，更多相关《IEC 60512-25-9-2008 Connectors for electrical equipment - Tests and measurements - Part 25-9 Signal integrity tests - Test 25i Alien crosstalk《电气设备用连接器.试验和测量.第25-9部分 信号完整性试验.试验25i 不同串音干扰》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60512-25-9 Edition 1.0 2008-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Connectors for electronic equipment Tests and measurements Part 25-9: Signal integrity tests Test 25i: Alien crosstalk Connecteurs pour quipements lectroniques Essais et mesures Partie 25-9: Essais dintgrit des signaux E

2、ssai 25i: Diaphonie exogne IEC 60512-25-9:2008 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including p

3、hotocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your

4、 local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les micr

5、ofilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre

6、pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electro

7、nic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The

8、IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Publis

9、hed details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in a

10、dditional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: cscie

11、c.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des

12、 publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la

13、 CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publication

14、s de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en angl

15、ais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous ave

16、z des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60512-25-9 Edition 1.0 2008-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Connectors for electronic equipment Tests and measurements Part 25-9: Signal integrity tes

17、ts Test 25i: Alien crosstalk Connecteurs pour quipements lectroniques Essais et mesures Partie 25-9: Essais dintgrit des signaux Essai 25i: Diaphonie exogne INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE R ICS 31.220.10 PRICE CODE CODE PRIX ISBN 2-8318-9971-0 Re

18、gistered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 60512-25-9 IEC:2008 CONTENTS FOREWORD.3 1 Scope and object5 2 Normative references5 3 Terms and definitions .5 4 Overview 6 4.1 Procedure6 4.2 Resources.7 5 Overall tes

19、t arrangement.7 5.1 General .7 5.2 Terminations .8 5.3 Pairs of connectors to test .8 6 Procedure to test alien crosstalk from one connector to another connector10 6.1 Calibration.10 6.2 Measurement (noise) floor .10 6.3 Alien crosstalk measurement .10 7 Procedure for determining significance11 8 De

20、tails to be specified in the detail specification12 9 Power sum calculation, report and documentation.12 Annex A (informative) Flow chart for obtaining alien crosstalk performance data.13 Annex B (informative) Illustrations of alien crosstalk testing using coaxial switching14 Bibliography18 Figure 1

21、 Schematic for testing without a switch.8 Figure 2 Schematic for terminations .8 Figure 3 Connector array9 Figure 4 Test directions11 Figure A.1 Flowchart for the test procedure 13 Figure B.1 Schematic for testing with a switch 14 Figure B.2 Example network analyzer, switch, and fixture with 8 balun

22、s in 2 clusters.15 Figure B.3 Example of fixture, in which balun clusters can slide left and right16 Figure B.4 Post can rotate three different directions17 60512-25-9 IEC:2008 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 25-9: Signal

23、integrity tests Test 25i: Alien crosstalk FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all q

24、uestions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publicat

25、ion(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC

26、collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opin

27、ion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to e

28、nsure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently

29、 to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendere

30、d responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its

31、technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other

32、 IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the s

33、ubject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60512-25-9 has been prepared by subcommittee 48B: Connectors, of IEC technical committee 48: Electromechanical components and mechanical structures for electronic equi

34、pment. The text of this standard is based on the following documents: FDIS Report on voting 48B/1915/FDIS 48B/1930/RVD This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of IEC 60512 series, under the general title Connectors for electronic equip

35、ment Tests and measurements, can be found on the IEC website. 4 60512-25-9 IEC:2008 The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific

36、publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 60512-25-9 IEC:2008 5 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 25-9: Signal integrity tests Test 25i: Alien crosstalk 1 Scope and object This part of IEC 60512

37、 defines a test method which is intended to assess the near-end alien crosstalk (ANEXT) and the far-end alien crosstalk (AFEXT) between connectors in close proximity, when mounted in their mounting systems. Both discrete modular connectors and multi-port panel connectors may be tested using this met

38、hod. This method provides a means to test the alien (exogenous) crosstalk between any two ports, as well as a means to assess the overall alien crosstalk from all other ports. This test procedure is generally applicable to any electrical connector, and is particularly suitable to connectors describe

39、d in IEC 60603-7 series, IEC 61076-3-104, and other types of connectors for data transmission. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest ed

40、ition of the referenced document (including any amendments) applies. IEC 60050-581, International Electrotechnical Vocabulary (IEV) Chapter 581: Electromechanical components for electronic equipment IEC 60512-26-100, Connectors for electronic equipment Tests and measurement Part 26-100: Measurement

41、setup, test and reference arrangements and measurements for connectors according to IEC 60603-7 (tests 26a to 26g) IEC 60603-7-4:2005, Connectors for electronic equipment Part 7-4: Detail specification for 8- way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 2

42、50 MHz IEC 60603-7 (all parts), Connectors for electronic equipment Part 7: Detail specifications for 8-way, (un)shielded, free and fixed connectors, for data transmissions IEC 61076-3-104:2006, Connectors for electronic equipment Part 3-104: Detail specification for 8-way, shielded, free and fixed

43、connectors, for data transmissions with frequencies up to 1000 MHz IEC 61156, Multicore and symmetrical pair/quad cable for digital communications 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 60050-581 apply as well as the following. 3.1 alien (ex

44、ogenous) crosstalk (AXT) signal coupling from disturbing conductor pairs into a disturbed pair of another connector 6 60512-25-9 IEC:2008 3.2 alien (exogenous) near-end crosstalk (ANEXT) loss signal coupling from a near-end disturbing conductor pair into a disturbed pair of another connector, measur

45、ed at the near-end 3.3 alien (exogenous) far-end crosstalk (AFEXT) loss signal coupling from a near-end disturbing conductor pair into a disturbed pair of another connector, measured at the far-end 3.4 power sum alien (exogenous) near-end crosstalk (PSANEXT) loss a computation of signal coupling fro

46、m multiple near-end disturbing conductor pairs, in one or more connectors, into a disturbed pair of another connector, measured at the near-end 3.5 power sum alien (exogenous) far-end crosstalk (PSAFEXT) loss a computation of signal coupling from multiple near-end disturbing conductor pairs, in one

47、or more connectors, into a disturbed pair of another connector, measured at the far-end 4 Overview 4.1 Procedure Alien crosstalk is a property that exists between connectors. It is affected by the properties of the connectors themselves, as well as the arrangement of the connectors in their mounting

48、 system, and the mounting systems themselves. Examples of mounting systems include faceplates, mounting boxes, frame-mounted panels, frames containing multiple panels, etc. Where necessary, connectors in other frame-mounted panels, etc., in close proximity shall be included as disturbing connectors.

49、 Alien crosstalk of the connector should be tested for all mounting systems in which the connector is intended to be mounted, or a sub-set thereof, as defined by the detail specification. Manufacturers may define a worst case mounting system, and test in either or both. This procedure may also be applied to multi-port connector panels, in which case each port of the panel s