IEC 60317-27-2013 Specifications for particular types of winding wires - Part 27 Paper tape covered rectangular copper wire《特种绕组线规格.第27部分 纸包扁铜线》.pdf

《IEC 60317-27-2013 Specifications for particular types of winding wires - Part 27 Paper tape covered rectangular copper wire《特种绕组线规格.第27部分 纸包扁铜线》.pdf》由会员分享，可在线阅读，更多相关《IEC 60317-27-2013 Specifications for particular types of winding wires - Part 27 Paper tape covered rectangular copper wire《特种绕组线规格.第27部分 纸包扁铜线》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60317-27 Edition 4.0 2013-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires Part 27: Paper tape covered rectangular copper wire Spcifications pour types particuliers de fils de bobinage Partie 27: Fil de section rectangulaire en cuivre recouvert

2、 de ruban papier IEC60317-27:2013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying a

3、nd microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC me

4、mber National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans

5、laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rside

6、nce. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all e

7、lectrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search

8、- www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on a

9、ll new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English an

10、d French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service C

11、entre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu tec

12、hnique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI e

13、n utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les no

14、uvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes qu

15、ivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60317-27 Edition 4

16、.0 2013-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires Part 27: Paper tape covered rectangular copper wire Spcifications pour types particuliers de fils de bobinage Partie 27: Fil de section rectangulaire en cuivre recouvert de ruban papier INTERN

17、ATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE M ICS 29.060.10 PRICE CODE CODE PRIX ISBN 978-2-8322-1154-0 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you o

18、btained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60317-27 IEC:2013 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms, definitions, general notes and appearan

19、ce 6 3.1 Terms and definitions 6 3.2 General notes 6 3.2.1 Methods of test 6 3.2.2 Winding wire 7 3.3 Appearance . 7 4 Dimensions 7 4.1 Conductor dimensions . 7 4.2 Tolerance on conductor dimensions 7 4.3 Rounding of corners 7 4.4 Increase in dimensions due to paper tape covering . 7 4.5 Maximum ove

20、rall dimensions . 8 5 Electrical resistance . 8 6 Elongation 8 7 Springiness 8 8 Flexibility and adherence 8 9 Heat shock . 8 10 Cut-through 8 11 Resistance to abrasion . 9 12 Resistance to solvents 9 13 Breakdown voltage . 9 14 Continuity of insulation . 9 15 Temperature index . 9 16 Resistance to

21、refrigerants . 9 17 Solderability . 9 18 Heat or solvent bonding 9 19 Dielectric dissipation factor . 9 20 Resistance to hydrolysis and to transformer oil . 9 21 Loss of mass 9 23 Pin hole test . 9 30 Packaging 10 Annex A (informative) Method of determination of x % proof stress: Rpx 11 Bibliography

22、 12 Figure A.1 Load-elongation diagram 11 Table 1 Increase in dimensions 8 60317-27 IEC:2013 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 27: Paper tape covered rectangular copper wire FOREWORD 1) The International Electrotechnical Commissio

23、n (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in ad

24、dition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee inter

25、ested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance wi

26、th conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested

27、IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible fo

28、r the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between

29、 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of confo

30、rmity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and membe

31、rs of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or

32、 any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication ma

33、y be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60317-27 has been prepared by IEC technical committee 55: Winding wires. This fourth edition cancels and replaces the third edition published in 1998, Amendm

34、ent 1: 1999. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: new subclause containing general notes on winding wire, formerly a part of the scope; revision to references to IEC 60317-0-2:2013 to cl

35、arify that their application is normative; new 3.3, Appearance; modification to 4.4, Increase in dimensions due to paper tape covering; deletion of Clause 22, High temperature failure; 4 60317-27 IEC:2013 new Clause 23, Pin hole test. The text of this standard is based on the following documents: FD

36、IS Report on voting 55/1414/FDIS 55/1435/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This International standard is to be r

37、ead in conjunction with the IEC 60317-0-2:2013. The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. A list of all parts in the IEC 60317 series, published under the gener

38、al title Specifications for particular types of winding wires, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specif

39、ic publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 60317-27 IEC:2013 5 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups

40、describing: 1) Winding wires Test methods (IEC 60851); 2) Specifications for particular types of winding wires (IEC 60317); 3) Packaging of winding wires (IEC 60264). 6 60317-27 IEC:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 27: Paper tape covered rectangular copper wire 1 Scope

41、This part of IEC 60317 specifies the requirements of paper tape covered rectangular copper winding wires. This covering consists of two or more layers of paper tape, all in the same direction and is primarily intended for winding coils for oil immersed transformers. The range of nominal conductor di

42、mensions covered by this standard is: width: min. 2,0 mm max. 16,0 mm; thickness: min. 0,80 mm max. 5,60 mm. The paper tapes covered by this standard are restricted to those specified in IEC 60554-1 having thicknesses in the range 25 m to 125 m inclusive. 2 Normative references The following documen

43、ts, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60317-0-2:2013, Specific

44、ations for particular types of winding wires Part 0-2: General requirements Enamelled rectangular copper wire IEC 60554-1, Specification for cellulosic papers for electrical purposes Part 1: Definitions and general requirements 3 Terms, definitions, general notes and appearance 3.1 Terms and definit

45、ions For the purposes of this document, the terms and definitions given in IEC 60317-0-2 and the following apply. 3.1.1 covering material which is wound, wrapped or braided around a bare or insulated conductor 3.2 General notes 3.2.1 Methods of test Subclause 3.2.1 of IEC 60317-0-2:2013 applies. In

46、case of inconsistency between IEC 60317-0-2:2013 and this standard, IEC 60317-27 shall prevail. 60317-27 IEC:2013 7 3.2.2 Winding wire The number of paper tapes, type of paper, paper tape thickness, and the degree of overlap shall be agreed upon between the purchaser and supplier. When a reference i

47、s made to winding wire according to this standard, the following information shall be given in the description: reference to IEC 60317-27; nominal conductor dimensions in millimetres (width thickness); nominal increase in dimensions due to paper. EXAMPLE: IEC 60317-27 4,00 1,00 + 0,20 proof stress m

48、inimum (and maximum) value EXAMPLES: IEC 60317-27 4,00 1,00 + 0,20 IEC 60317-27 7,00 2,50 + 1,00 Rp0,2 = 150 MPa 3.3 Appearance The conductor shall be essentially free from copper dust and other extraneous matter when examined with normal vision, as wound on the original spool or reel. The paper cov

49、ering shall be of one or more tapes wrapped firmly, closely, evenly, and continuously around the conductor. No bonding or adhesive material shall be used except to anchor the ends of paper tapes. 4 Dimensions 4.1 Conductor dimensions Subclause 4.1 of IEC 60317-0-2: 2013 applies. 4.2 Tolerance on conductor dimensions Subclause 4.2 of IEC 60317-0-2: 2013 applies. 4.3 Rounding of corners Subclause 4.3 of IEC