TIA-723-1998 High Speed 232 Type DTE DCE Interface《高速232型 DTE DCE接口》.pdf

《TIA-723-1998 High Speed 232 Type DTE DCE Interface《高速232型 DTE DCE接口》.pdf》由会员分享，可在线阅读，更多相关《TIA-723-1998 High Speed 232 Type DTE DCE Interface《高速232型 DTE DCE接口》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA-723-1998 APPROVED: SEPTEMBER 3, 1998 REAFFIRMED: MAY 20, 2003 REAFFIRMED: DECEMBER 7, 2012 TIA-723 September 1998High Speed 232 Type DTE/DCE Interface NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufa

2、cturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member o

3、r non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted

4、 by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all

5、safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Project No. 3-3855-RF2, for

6、mulated under the cognizance of the TIA TR-30.2 Subcommittee on DTE-DCE Interfaces and Protocols.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Technology (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form;

7、(c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TI

8、A makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims a

9、ny obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are re

10、asonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organizati

11、on (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) the

12、n (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and publi

13、shed pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance wi

14、th the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNI

15、NG THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTA

16、TIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DA

17、MAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREA

18、CH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT

19、SUCH LIMITATIONS. STD-EIA TIA-723-ENGL 1978 3234b00 Ob05011 28T m TINEIA-723 HIGH SPEED 232 TYPE DTWDCE INTERFACE (From Standards Proposal No . 3855 formulated under the cognizance of TIA Subcommittee TR-30.2 on Data Transmission Interfaces) Contents Page 1 SCOPE . 1 1 . 1 Section abstracts . 1 1.2

20、Application 1 1.3 Serialization 1 1.4 Synchronoushonsynchronous communication . 1 1.5 Classes of service . 1 2 NORMATIVE REFERENCES . 1 3 SIGNAL CHARACTERISTICS 2 3.1 Electrical characteristics 2 3.2 Protective ground (frame ground) . 2 3.3 Shield (25 and 26-position connectors) . 2 3.4 Circuit grou

21、nding (Signal Common) 2 3.5 “Fail Safe” operation 3 3.6 General signal characteristics . 3 3.6.1 Distortion . 3 3.6.2 Timing . 3 4 INTERFACE MECHANICAL CHARACTERISTICS . 5 4.1 Definition of mechanical interface 5 4.2 25-position interface connector . . 5 4.3 Alt A 26-position interface connector . 5

22、 4.4 Alt B 9-position interface connector . 6 i TINEIA-723 4.5 Connector contact assignments 16 5 FUNCTIONAL DESCRIPTION OF INTERCHANGE CIRCUITS 17 5.1 5.2 5.3 5.3.1 5.3.2 5.3.3 5.3.4 5.3.5 5.3.6 5.3.7 5.3.8 5.3.9 5.3.1 O 5.3.1 1 5.3.12 5.3.1 3 5.3.14 5.3.1 5 5.3.1 6 5.3.1 7 5.3.18 5.3.1 9 5.3.20 5.

23、3.21 5.3.22 General . 17 Classifications of circuits . 17 Definitions of interchange circuits 17 Circuit AB . Signal Common 17 Circuit BA . Transmitted Data 18 Circuit BB . Received Data 19 Circuit CA - Request to Send 19 Circuit CB - Clear to Send . 20 Circuit CC - DCE Ready 20 Circuit CD . DTE Rea

24、dy 21 Circuit CE - Ring Indicator . 22 Circuit CF - Received Line Signal Detector 22 Circuit CJ - Ready for Receiving 22 Circuit CK - Received Energy Present . 23 Circuit LL - Local Loopback . 23 Circuit RL - Remote Loopback . 24 Circuit TM - Test Mode 24 Circuit DA - Transmitter Signal Element Timi

25、ng (DE Source) 24 Circuit DB - Transmitter Signal Element Timing (DCE Source) 25 Circuit DD - Receiver Signal Element Timing (DCE Source) . 25 Circuit SBA - Secondary Transmitted Data 26 Circuit SBB - Secondary Received Data 26 Circuit SCA . Secondary Request to Send 26 Circuit SCB - Secondary Clear

26、 to Send . 26 Circuit SCF - Secondary Received Line Signal Detector . 26 6 RECOMMENDATIONS AND EXPLANATORY NOTES 27 6.1 Line signals . 27 6.2 Use of circuits for testing . 27 6.2.1 Local loopback 28 6.2.2 . Remote loopback 28 6.2.3 Test mode . 29 6.3 Use of Circuit LL for “Busy Out“ 29 L Annex A (in

27、formative) . 30 ii TINEIA-723 FOREWORD (This foreword is not part of this Standard.) This standard was developed to provide a DTE/DCE interface, similar to TINEIA-232, operating at data rates up to 512 kbit/s. It is interoperable with TINEIA-232-F and TINEIA-687 at lower data rates. This interface p

28、rovides three different connectors: the standard 25-pin connector, Alternative A 26-pin full function connector and Alternative B 9-pin for non-synchronous use . 111 STD-EIA TIA”723-ENGL 1998 m 3234b00 Ob05014 T77 W TINEIA-723 I SCOPE I .I Section abstracts This Standard is applicable to the interco

29、nnection of data terminal equipment (DTE) and data circuit-terminating equipment (DCE) employing serial binary data interchange with control information exchanged on separate control circuits. It defines: Section 2 NORMATIVE REFERENCES Section 3 SIGNAL CHARACTERISTICS Section 4 INTERFACE MECHANICAL

30、CHARACTERISTICS Section 5 FUNCTIONAL DESCRIPTION OF INTERCHANGE CIRCUITS Section 6 RECOMMENDATIONS AND EXPLANATORY NOTES I .2 Application This Standard applies where equipment on one side of the DTUDCE interface is intended for connection directly to equipment on the other side without additional te

31、chnical considerations. Applications where cable termination, signal waveshaping, interconnection cable distance, and mechanical configurations of the interface must be tailored to meet specific user needs are not precluded but are beyond the scope of this Standard. I .3 Serialization This Standard

32、applies to data communication systems where the data is bit serialized. No restrictions are placed on the sequence of bits. 1.4 Synchronoushonsynchronous sommunication This Standard applies to both synchronous and nonsynchronous serial binary data communications systems. I .!i Classes of service Thi

33、s Standard applies to switched, nonswitched, dedicated, leased or private line service. Consideration is given to both point-to-point and multipoint operation. 2 NORMATIVE REFERENCES The following standards contain provisions which, through reference in this text, constitute provisions of this Stand

34、ard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions of the standards 1 TINEIA-723 indicated below. ANSI and TIA m

35、aintain registers of currently valid national standards published by them. ANSIKINEIA-334-B Signal Quality at Interface Between Data Terminal Equipment and Synchronous Data Cinuit-Terminating Equipment for Serial Data Transmission ANSITTINEIA-404-B Standard for Statt-Stop Signal Quality for Non-Sync

36、hronous Data Terminal Equipment ANSITTINEIA-694 Electrical Characteristics of Unbalanced Digital lnterface for Signaling Rates up to 512 kbWs 3 SIGNAL CHARACTERISTICS 3.1 Electrical characteristics The electrical characteristic of the interchange circuits are specified in ANSITTINEIA-694. The meanin

37、g of circuit conditions “ON“ and “OFF“ for control and timing circuits, and “O“, “I“, “MARK“, and “SPACE“ for data circuits, shall be as defined in ANSITTINEIA-694. 3.2 Protective ground (frame ground) In DTEs and in DCEs, protective ground is a point that is electrically bonded to the equipment fra

38、me. It may also be connected to external grounds (e.g., through the third wire of the power cord). It should be noted that protective ground (frame ground) is not an interchange circuit in this Standard. If bonding of the equipment frames of the DCE and the DTE is necessary, a separate conductor sho

39、uld be used that conforms to the appropriate national or local regulation applying to wire size and color coding. 3.3 Shield (25 and 2:bposition connectors) In order to facilitate the use of shielded interconnecting cable, interface connector contact number 1 is assigned for this purpose. This will

40、permit the cable associated with the DTE to be composed of tandem connectorized sections with continuity of the shield accomplished by connection through this contact in the connectors. Normally the DCE should make no connection to interface connector contact number 1. It is recognized that for cert

41、ain electromagnetic interference (EMI) suppression situations, additional provisions may be necessary but are beyond the scope of this Standard. 3.4 Circuit grounding (Signal Common) Proper operation of the interchange circuits requires the presence of a path between the DTE circuit common and the D

42、CE circuit common. This path is obtained by means of two interchange Circuits AB, Signal Commons. Both the DCE and the DTE normally should have 2 TINEIA-723 their circuit common connected to their protective ground through a resistance of 100 ohms (k20%) having a power dissipation rating of one-half

43、 watt. Figure 1 illustrates the signal common and grounding arrangement. 3.5 “Fail Safe” operation The receivers of the following interchange circuits: Circuit CC (DCE Ready) Circuit CA (Request to Send) Circuit CD (DTE Ready) shall be used to detect a power-off condition in the equipment connected

44、across the interface and the disconnection of the interconnection cable. Detection of either of these conditions shall be interpreted as an OFF condition of the interchange circuit. 3.6 General signal characteristics 3.6.1 Distortion Interchange circuits transfemng data signals across the interface

45、point shall hold the marking (binary ONE) and spacing (binary ZERO) conditions for the total nominal duration of each signal element. Distortion tolerances for synchronous systems are set forth in TINEIA-334-B. Distortion tolerances for nonsynchronous systems are set forth in TINEIA-404-B. 3.6.2 Tim

46、ing Interchange circuits transferring timing signals across the interface point shall hold ON and OFF conditions for nominally equal periods of time consistent with acceptable tolerances as specified in TINEIA-334-B. Accuracy and stability of the timing information on Circuit DD (Receiver Signal Ele

47、ment Timing) is required only when Circuit CF (Received Line Signal Detector) is in the ON condition. Drift during the OFF condition of Circuit CF is acceptable: however, resynchronization of the timing information on Circuit DD must be accomplished as rapidly as possible following the OFF to ON tra

48、nsition of Circuit CF. It is desirable that the transfer of timing information across the interface be provided during all times that the timing source is capable of generating this information (.e., it should not be restricted only to periods when actual transmission of data is in progress). During

49、 periods when timing information is not provided on a timing interchange circuit, the interchange circuit shall be clamped in the OFF condition. Tolerances on the relationship between data and associated timing signals shall be in accordance with TINEIA-334-B. 3 TINEIA-723 i; Unbalanced common Frame Ground circuit AB i Signal Commons f f i Note 2 Shield i I GWG GWG I (Note 1) (Note 1) Note 1 : GWG is green wire ground of power system Note 2: Normally no connection to shield in DCE (see 2.3) Figure I - Signal Common and Grounding Arrangement 4 4 INTERFACE MECHANICAL CHARACTERISTI