SAE AS 5135-1997 Desiccant Port and Desiccant Holder《干燥剂通道和干燥剂容器》.pdf

《SAE AS 5135-1997 Desiccant Port and Desiccant Holder《干燥剂通道和干燥剂容器》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 5135-1997 Desiccant Port and Desiccant Holder《干燥剂通道和干燥剂容器》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDAS5135Issued 1997-07D esiccant P ort and D esiccant H older1. SCOPE:This SAE Aerospace Standard (AS) describes the characteristics of a desiccant port installed through the flat wall of a shipping and storage container. With the cover removed, the desiccant port shall provide acces

2、s to the interior of the container for installation and removal of desiccant.2. APPLICABLE DOCUMENTS:The following publications form a part of this specification to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue of other publications shall be the

3、issue in effect on the date of the purchase order. In the event of conflict between the text of this specification and references cited herein, the text of this specification takes precedence. Nothing in this specification, however, supersedes applicable laws and regulations unless a specific exempt

4、ion has been obtained.2.1 ASTM Publications :Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.ASTM B 633 Electrodeposited Coatings of Zinc on Iron and SteelASTM B 841 Class 1 Type B - Zinc Nickel Electro PlatingASTM D 2000 Rubber Products in Automotive Applications2.2 ANS

5、I Publications :Available from ANSI, 11 West 42nd Street, New York, NY 10036-8002.ANSI/ASQC Z1.4 Sampling Procedures and Tables for Inspection by AttributesReaffirmed 2005-10SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engin

6、eering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may

7、be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2005 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying

8、, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this T

9、echnical Report, please visit http:/www.sae.org/technical/standards/AS5135 SAE AS5135 - 2 -3. CLASSIFICATION :This description covers desiccant ports as follows:Type I: Desiccant Port, aluminum alloy body with 300 series stainless steel cover with tabsType II: Desiccant Port, aluminum alloy body wit

10、h 300 series stainless steel cover without tabsType III: Desiccant Port, aluminum alloy body with zinc-nickel plated steel cover with tabsType IV: Desiccant Port, aluminum alloy body with zinc-nickel plated steel cover without tabsType V: Desiccant Port, aluminum alloy body with zinc plated steel co

11、ver with tabsType VI: Desiccant Port, aluminum alloy body with zinc plated steel cover without tabsStyle A: Cover with small hole, 26 mm (1.050 in) diameterStyle B: Cover with large hole, 52 mm (2.015 in) diameterStyle C: Cover with no holeClass 1: Without desiccant holderClass 2: With desiccant hol

12、derSize A: 178 mm (7 in), long desiccant holder (holds two 8 unit bags)Size B: 305 mm (12 in), long desiccant holder (holds four 8 unit bags)Size C: 432 mm (17 in) long desiccant holder (holds six 8 unit bags)4. SALIENT CHARACTERISTICS:Tolerances on all parts shall be the same as those identified by

13、 the industry for that product. The desiccant port assembly shall have an expected service life of 20 years. The desiccant port shall be capable of functioning properly between -54 and +71 C (-65 and +160 F), when installed through a 102 mm (4.015 in) diameter hole in the wall of a reusable shipping

14、 and storage container, with a wall thickness up to 7 mm (0.30 in). The desiccant port shall be capable of maintaining the container environmental seal at 34 kPa (5 psig) pressure or 34 kPa (5 psig) vacuum. The desiccant port cover shall be capable of being removed by hand, requiring no tools to ope

15、rate. With the cover removed, the desiccant port shall provide access to the interior volume of the desiccant holder for installation and removal of desiccant.SAE AS5135 - 3 -4.1 Interface Requirements :The desiccant port shall be designed such that it will fit a 102 mm (4.015 in) diameter hole in a

16、 flat surface in the container wall. Figure 1 shows one possible configuration of an acceptable desiccant port. Other designs are acceptable provided they meet the basic functional and dimensional requirements specified herein.4.2 Desiccant Port Body:The opening through the desiccant port body shall

17、 have a minimum diameter of 87 mm (3.44 in). The overall length of the desiccant port body shall not exceed 51 mm (2.00 in). The desiccant port outside the container including the flange shall not exceed 26 mm (1.00 in). The desiccant port body shall prevent over compression of the gasket and retain

18、 the gasket in position when installed. The port body or components shall not cause galvanic corrosion with steel or aluminum containers over the expected life span of 20 years.4.3 Cover Assembly:The desiccant port cover assembly shall be capable of maintaining pressure or vacuum without any leakage

19、 when installed. The desiccant port cover shall be capable of being installed or removed with no more than one half turn of the cover, by hand, without the use of tools. The Type III and IV StyleB cover assembly made from steel shall have a zinc-nickel electroplating applied 0.08 mm (0.003 in) thick

20、 in accordance with ASTM B 841 Class 1 Type B. The Type V and VI cover assembly made from steel shall have a zinc plate per ASTM B 633, Type II, Sc 3. The holes provided in Style A and B are for the installation of a pressure relief valve. A flat recessed area in the desiccant port cover assembly sh

21、all be provided for the holes. The recessed area shall be 15 mm (0.62 in) deep when measured from the outside surface of the desiccant port cover and 70 mm (2.75 in) in diameter. A minimum of three tabs to ease the removal/installation of the cover are required on TypeI, III, and V . The tabs shall

22、be approximately 12 mm (0.50 in) high and shall not interfere with the desiccant port functionality or environmental seal. The desiccant port cover shall provide for venting of internal pressure, while opening, before complete removal is possible.4.4 Gasket:The gaskets, when installed in accordance

23、with the manufacturers instructions, shall prevent air leakage. Gasket material used shall be ethylene propylene diene material (EPDM) or silicone in accordance with ASTM D 2000.4.5 Washer:The washer shall be used as a buffer between the surface of the container wall and the nut used to secure the d

24、esiccant port body. The washer shall be aluminum. SAE AS5135 - 4 -FIGURE 1 - Shows One Possible Configuration of an Acceptable Desiccant PortSAE AS5135 - 5 -4.6 Nut :The nut shall secure the desiccant port body through the container wall so that there is no loosening during container testing or loss

25、 of environmental seal. The nut shall be capable of withstanding a torque of 17 Nm (150 in-lb). The nut shall be the same material as the desiccant port body.4.7 Retaining Cable/Lanyard:The desiccant port cover assembly shall be tethered to the desiccant port body with a stainless steel braided cabl

26、e/lanyard. The cable shall be long enough to allow for installation and removal of the cover assembly without interference and short enough that it does not interfere with other operations, or pose a safety hazard, i.e., entanglement. The attachment point on the main body shall utilize 300 series st

27、ainless steel screws. A provision for replacement of the cover shall be provided without adversely effecting the security seal requirements.4.8 Security Seal Provision:A security seal provision shall be provided to reveal unauthorized entry into the container cavity. A hole may be drilled through th

28、e desiccant port body flange for security seal attachment.4.9 Desiccant Holder:The desiccant holder shall be aluminum, not less than 85 mm (3.35 in) inside diameter, and permanently attached to the desiccant port and retain the desiccant unit bags as required. The desiccant holder shall have holes i

29、n it that will allow for the free passage of air from the container to the desiccant. Three different length desiccant holders are available. All other characteristics of the desiccant port, desiccant port assembly, nut, and washer shall be as specified. A provision for attachment of desiccant holde

30、r may be provided for securing support of holder opposite opening end.4.10 Product Marking:The cover assembly shall be marked with manufacturers name and part number, as well as instructional marking on opening and closing using best commercial practice.SAE AS5135 - 6 -5. TEST REQUIREMENTS :5.1 Leak

31、 Testing:Desiccant Port assembly shall show no evidence of leaking in either direction when submerged under water for a minimum of 1 min and pressurized to 28.0 +7.0 -0.0 kPa (4.0 +1.0 -0.0 psig). Sample lot size shall be selected in accordance with ANSI/ASQC Z1.4 1993, Table I, General Inspection L

32、evel II, Single Sample Plan 1.5 AQL. A recommended test procedure is to seal the hole in the cover assembly, if applicable, install the desiccant port into a small test fixture that can be pressurized on one side while the opposite side is submerged under water a minimum of 6 mm (0.25in). Release of

33、 any air bubble from the submerged surface within a 1 min period shall be cause for rejection. Reverse the desiccant port assembly in the test fixture and repeat the above test so the opposite surface can be submerged and examined for leakage.5.2 Cover Assembly Test:The desiccant port cover assembly

34、 shall be capable of being removed by hand.6. QUALITY ASSURANCE PROVISIONS:The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of the document. The product shall conform to the producers own drawings, specifications, standards,

35、 and quality assurance practices. If port has not been previously supplied by vendor, a first article shall be required. A sample shall be subjected to first article inspection and a copy of relevant test reports shall be provided.PREPARED BY SAE SUBCOMMITTEE EG-1D, PROPULSION TRANSPORTATION EQUIPMENT OF COMMITTEE EG-1, AEROSPACE PROPULSION SYSTEMS SUPPORT EQUIPMENT